Report presenting an investigation to determine the spin, recovery, and longitudinal-trim characteristics of a 60 degree delta-wing model through an extensive range of mass loadings. Variations in the relative density, center-of-gravity position, and inertia parameters were included in testing. Results regarding the single-vertical-tail and multiple-vertical-tail configurations are provided.

Memorandum presenting wind tunnel tests to determine the aerodynamic characteristics of a semispan wing with a modified NACA 0012-64 section and a 26.6-percent-chord, plain, trailing-edge aileron. Results are shown for the wing with the 0.229-chord line unswept and swept back 45 degrees and for a Mach number range from 0.40 to 0.925.

Report presenting the vibration characteristics of several symmetrical ball-root-type blades simulating the mass and natural frequency of axial-flow-compressor blades under various mounting conditions by subjecting them to controlled periodic excitation and centrifugal loading. Results regarding loose single ball-root mounting, loose-lubricated, single ball-root mounting, double ball-root mounting, and damping measurements are provided.

An experimental investigation was made at Mach number 1.90 of the performance of a series of perforated convergent-divergent supersonic diffusers operating with initial boundary layer, which was induced and controlled by lengths of cylindrical inlets affixed to the diffusers. Supercritical mass-flow and peak total-pressure recoveries were decreased slightly by use of the longest inlets (4 inlet diameters in length). Combinations of cylindrical inlets, perforated diffusers, and subsonic diffuser were evaluated as simulated wind tunnels having second throats. Comparisons with noncontracted configurations of similar scale indicated conservatively computed power reductions of 25 percent.

Report presenting an investigation in the high speed tunnel to determine the effects of several wing-mounted external-store configurations on the aerodynamic characteristics of a model of a swept wing-fuselage combination for a range of Mach numbers. Some of the configurations explored included inboard underwing installations and wing-tip installations. Results regarding lift-drag ratios, drag characteristics, lift-curve slope, and pitching-moment characteristics are provided.

From Summary: "A flight investigation was made of a supersonic twin-ram-jet test vehicle using short-flame-length burners. The test demonstrated a maximum acceleration of 3.6g and a maximum flight Mach number of 3.02. Data were obtained over a Mach number range from about 1.9 to 3.0, an altitude range from 1,800 to 40,900 feet, and a fuel-air-ratio range from 0.012 to 0.065."

Report discussing tests of an unshrouded axial-flow supersonic compressor rotor. Information about the pressure ratio, efficiency, and flow rate with and without inlet guide vanes is provided. The results are also compared to testing on the original shrouded rotor.

Report presenting the results of static tests conducted for the purpose of determining the lift forces and hinge moments associated with a flat-plate paddle vane, externally hinged near a rocket-nozzle exit and operating on the jet for vane deflection angles ranging from -4 degrees to 25 degrees. Results regarding vane aerodynamic characteristics, performance of rocket motor, and vane erosion

Report presenting an investigation to determine the aerodynamic characteristics of a wing-fuselage configuration with a wing with quarter-chord line swept back 35 degrees, an aspect ratio of 4, a taper ratio of 0.6, and an NACA 65A006 airfoil section. Lift, drag, and pitching-moment characteristics, downwash angles, and wake characteristics for various angles of attack and Mach numbers are provided.

From Introduction: "Results are presented to indicate the effect of altitude, flight Mach number, and exhaust-nozzle-outlet area on the combustion efficiency, the losses in total pressure occurring in the combustion chamber, and the fractional loss in engine cycle efficiency resulting from combustion-chamber pressure losses. The engine cycle efficiency is also presented.These results are shown graphically as a fraction of corrected engine speed and in tabular form."

"Tabulated pressure coefficients and aerodynamic characteristics are presented unanalyzed for six spanwise stations on the right wing of the Douglas D-558-I research airplane (BuAero No. 37972). The data were obtained in a 1 g stall at subcritical Mach numbers, in a speed run to a Mach number of 0.90 and in a wind-up turn at a Mach number of 0.86" (p. 1).

An investigation has been conducted in the Langley 4- by 4-foot supersonic tunnel at Mach numbers 1.40 and 1.59 to determine the effect of aileron profile on the aerodynamic characteristics of a complete model of a supersonic aircraft configuration. The model had a 40 degree sweptback tapered wing with 10-percent-thick circular-arc sections normal to the quarter-chord line. The ailerons were 20-percent chord and were located on the outboard 50 percent of the wing semispans. The various ailerons investigated included the basic circular-arc profile and three flat-sided ailerons having ratios of trailing-edge thickness to hinge-line thickness t of 0, 0.5, and 1.0. Low aileron effectiveness was obtained with the circular-arc and t = 0 profiles. Increasing the trailing-edge thickness (t = 0.5 and 1.0) resulted in increased effectiveness as well as increased hinge moments with only a slight increase in drag.

Report presenting an investigation of the hydrodynamic characteristics of a model of a 130,000-pound transonic flying-boat design with a high length-beam ratio planing-tail hull, sweptback gull wings with wing-tip floats, and wing-root jet-power-plant installation. Results regarding the aerodynamic, hydrostatic, and hydrodynamic qualities are provided.

Report presenting the use of Theodorsen's propeller theory to calculate the performance of a dual-rotating propeller with nonideal load distributions. Results regarding the propeller characteristics were made for several blade-angle settings and flight Mach numbers.

Report presenting the results of a free-flight investigation of two drag research models equipped with canopies for a range of Mach numbers from 0.8 to 1.5. The main difference between the models was the location of the canopy, which was at the 15-percent fuselage station on one model and the 25-percent fuselage station on the other. The additional drag due to the canopies was about 10 to 20 percent of the total configuration drag at supersonic speeds.

Memorandum presenting a description of a method of telemetering skin temperature using a small resistance wire pickup with a time constant of less than 0.003 second to determine boundary-layer heat-transfer coefficients. An evaluation of the accuracy of the method of measuring the heat-transfer coefficient is given for a particular application.

"Flutter tests of sweptback cantilever wing models have been made in a small intermittent two-dimensional supersonic tunnel where the testing technique involved changing the structural parameters so that the models would flutter at the tunnel design Mach number of 1.3. Data for 21 models covering sweep angles from 30 degrees to 60 degrees and with varying parameters are included" (p. 1).

From Introduction: "Altitude-chamber and wind-tunnel investigations of the performance of turbojet engines such as those reported in references 1 to 4 have shown that the conventional correction factors fail to generalize the engine performance variables at high altitudes. An investigation was therefore made at the NACA Lewis laboratory to determine the altitude performance of the J33-A-23 turbojet engine and to demonstrate the magnitude of departure of actual altitude performance from that predicted from sea-level performance."

Report presenting an experimental investigation to determine the combustion properties of several magnesium-hydrocarbon slurry blends and to indicate the feasibility of the application of slurry-type fuels to high-speed aircraft. High-concentration magnesium slurries showed large improvements in combustion stability and tail-pipe-burner net thrust.

Report presenting pressure distributions, wake measurements, and tuft patterns for wings with 30 and 45 degrees of sweepback in conjunction with a midwing fuselage at Mach numbers to 0.96. The wings have an NACA 65-210 section, a taper ratio of 2.6:1, and aspect ratios of 7.5 and 5.2. The study indicated that when the Mach number reached high subsonic values at low angles of attack, the locations of peak negative pressure coefficients on the upper surfaces of the sections near the wing-fuselage junctures shifted rearward.

Report presenting pressure distributions and wake measurements for wings with 30 and 45 degrees of sweepforward, in conjunction with a midwing fuselage, at Mach numbers up to 0.96. The wings had an NACA 65-210 section, a taper ratio of 0.38, and aspect ratios of 7.5 and 5.2. Results regarding pressure distributions, wake measurements, and corrections are provided.

Report discussing the drag and pressure recovery of a model with a nose inlet with a parabolic arc at zero angle of attack. External drag coefficient and total-pressure recovery at the end of the diffuser were measured at a range of Mach numbers and mass-flow ratios.

The effectiveness of molybdenum disulfide MoS2 as a bearing lubricant was determined at high temperature and at high speeds. A 1-inch-bore ball bearing operated at temperatures to 1000 F, a speed of 1725 rpm, and a thrust load of 20 pounds when lubricated only with MoS2-air mist. A 75-millimeter-bore cageless roller bearing, provided with a MoS2-syrup coating before operation, operated at DN values to 1 x 10(exp 6) with a load of 368 pounds.

Report presenting an investigation in the 7- by 10-foot tunnel to determine the transonic aerodynamic characteristics of a wing with a spanwise variation in thickness ratio. The wings investigated had 45 degrees of sweepback, aspect ratio 8, taper ratio 0.45, and airfoil sections tapered from an NACA 63A010 section at the root chord to an NACA 63A006 section at the tip chord. Results regarding lift characteristics, drag characteristics, and pitching-moment characteristics are provided.