The calculation of shielding the thickness for plutonium is complicated by the many different energies represented in the gamma radiation emitted during decay of the plutonium isotopes. Dose rate predictions are also frequently confused by gamma from varying content of fission product impurities in the plutonium, as well as other gamma radiation induced through alpha and neutron particle absorption within the source material or its environment. After assumptions are made for these many factors the radiation data for shielding determination is still frequently inadequate because of wide variations in dose rates resulting from self-absorption. The degree if self-shielding is in turn dependent on nature of the plutonium compound, degree of compactness, weight, and over-all geometrical distribution of the source material. By preparing a variety of plutonium samples representing combinations of these varying factors, actual dose rates and gamma spectra, as obtained from them, can then be extrapolated for application to specific situations.

Summary: "Criticality was considered impossible in any contingency encountered in practice under either of the following conditions which include no safety factor: (a) In any isolated cylinder not more than 5 in. in disruptor, if the total amount of U235 present does not exceed 7.5 Eg. (b) In an isolated vessel of any shape and size, if the total amount of U235 present does not exceed 880 g. An "isolated" vessel is one which does not "see" more than 0.1 [...] other vessels containing fissionable material."

A multi-purpose program for processing exponential data has been prepared for the 709 computer. The main purposes of the program is to compute the material buckling from raw data (given counts, time, and counter information) or from previously calculated Athermal's. It is also possible to compute only CeCh (end and harmonic corrections) for a given B11 or series if B11's no counting data being entered. In every case, pile measurements must be submitted as input for corrections.

Water treatment systems for preparing and maintaining high purity water in out-of-reactor or in-reactor test oops are becoming increasingly important. In out0of-reactor experiments the presence of ionic impurities in the water has a marked influence on film formation and corrosion rates. It is therefore , imperative that these impurities be maintained at the lower practical concentration.

The preparation of radioactive metallurgical specimens for microscopic examination is one of the responsibilities of the Radiometallurgy Sub-Unit. An abrasive cut-off machine development program, based upon a previous experimental model, was undertaken to provide a method for sectioning of irradiated materials without undue personnel exposure or spread of contamination and finally to provide data for the design of an abrasive cutting unit for use in the work cells in the Radiometallurgy Building. A horizontal-feed type set-off machine, powered by a 7 1/2 hp motor with V-belt drive, has been developed for the submerged sectioning of irradiated uranium and is currently being used successfully to obtain samples for metallurgical, chemical and physical investigations without excessive personnel exposure or spread of radioactive contaminates.

Abstract: An investigation was conducted to determine the absorption and translocation of fission products by Russian thistle from a localized spot of contaminated soil. The amount and identity of the radioactive elements absorbed and translocated by the Russian thistle is given along with the location of these elements in the plants. Beta radioactivity to the amounts of 10 microcuries per gram caused no visible effects on the growth habits of sectioned material are included.

The following document describes data collected from a 14-month period of analyzing crustaceans containing radioactivity. Provided is information based on the change of radioactivity through seasonal changes.

Abstract: The data obtained from the radioassay of fish collected in vicinity of the Hanford Works between April, 1948 and June, 1950 are presented. Most of the radioactivity in the fish resulted from the concentration of p32 in the scales, bone, and certain visceral organs. The level of activity density in the fish was influenced by size, feeding habits and metabolic rate in addition to the activity density of the water. Changes in operation of nuclear reactors have resulted in progressive increases in activity densities of fish from one year to the next. The levels of radioactivity are not sufficiently high to be hazardous to either the fish or persons eating them.

The Non-Production Fuel Reprocessing Program involves the chemical processing of valuable reactor fuels received from privately owned power reactors. It is necessary therefore, to accurately measure the fuel material received in order to insure proper payment to reactor operator and to provide the Atomic Energy Commission with appropriate accountability data. The volume measurement study described herein was conducted in order to determine the limits of accuracy that could be obtained in measuring relatively large volumes of solution under plant processing conditions.

From introduction: "This report provides background information regarding the study results presented in the first volume of this report and provides information resulting from the studies made on the gas cooled reactor concept."

An addendum to report HW-30390 a additional power generation calculation for P, the rate of energy release, in kilowatts, was derived.

The process of age calculation for Hanford exponential lattices containing aluminum-matrix slugs, where the sums run over the materials of the lattice cell.

Disposal of liquid radioactive wastes to ground requires knowledge of the area ground-water hydrology. Information is desired on direction and velocity of ground-water flow. Direction of flow can be determined from maps showing contours on the water table surface, such contours being derived from well water elevations. Ground-water velocity is more difficult to ascertain.

Experimental combination hand and shoe counter redesign as a compact, simplified, register readout instrument no larger than the present Five-Fold called Model 2.

Since the start of E-metal processing in December, 1958, critical mass control in the Redox dissolvers has been provided by a combination of administrative controls, revised dissolver charging procedures, and new dissolving processes and operation control procedures. These were all based on a maximum allowable charge of E-Metal to the dissolvers which was equivalent to 45 percent of the minimum critical mass.

An experiment now in progress should give some accurate information about the thermal neutron absorption cross section of carbon 12. This report outlines and summarizes this experiment and analyzes it to determine the main sources of error and the probably error in the final result.

Summary: A method was found for determining calcium concentrations in TBP process streams in spite of serious interferences bysodium, ferrous, uranyl, sulfate, phosphate, and sulfamate ions as well as by TBP. The precision attainable varied from sample to sample, depending upon its composition. In general, errors of 20% or greater occurred. The smallest determinable amount of calcium was about 10 mg/1.

Report detailing an analysis of the deposition of I-131 on vegetation. Analysis was necessary to determine the potential hazards of the gases from the dissolution of the metal on vegetation.

Report detailing the refractive index of solutions of uranyl nitrate, nitric acid and aluminum nitrate. This report builds upon preliminary data and a brief discussion that from a previous report. This report covers more accurate and detailed data that had be accumulated following the initial report.

From introduction: The present report describes further refinements of the apparatus and the method to meet a need for a sensitive determination of carbon in plutonium.

Report describing the results of the cupferron extraction-copper spark method in determining the impurity elements in plutonium metal. This was required the 234-5 Project analytical program.

Report describing methods of determining trace impurities in plutonium in connection with the Metal Fabrication Process. The methods included are the cupferron extraction-copper spark method and the direct copper spark method.

A report describing a the results of a fluorimetric and volumetric method for the determination of fluoride. This method was developed for the determination of ionizable fluorine in gases in the range of 1-500ppm. This method was chosen because the determination depends on the generation of a color rather than the bleaching effect or on a change of color.

Five continuous coatings were produced on zirconium coupons using an anodizing technique. These layers appear to be quite adherent and not subject to visible or audible failure caused by flaxion of the basis metal, Their abrasion resistance, though not investigated thoroughly, appears to be moderately good.