"The design, construction, and properties of an electrical-resistance strain gage consisting of fine wires molded in a laminated plastic are described. The properties of such gages are discussed and also the problems of molding of wires in plastic materials, temperature compensation, and cementing and removal of the gages. Further work to be carried out on the strain gage, together with instrument problems, is discussed" (p. 1).

From Summary: "Methods are described for calculating the period and frequency of vibration of cantilever wings and similar structures in which the weight and moment of inertia vary along the span. Both the beam and torsional frequencies may be calculated by these methods. The procedure is illustrated by examples."

Note presenting the body of knowledge that has been accumulated in the field of noise reduction in aircraft. Special attention is paid to effective soundproofing schemes.

"Sound pressure of the first four harmonics of rotation from a full-scale two-blade propeller were measured and are compared with values calculated from theory. The comparison is made (1) for the space distribution with constant tip speed and (2) for fixed space angles with variable tip speed. A relation for rotation noise from an element of radius developed by Gutin is given showing the effect of number of blades on the rotation noise" (p. 1).

"Tests were made to determine the effectiveness of a long-period dynamically overbalanced flap in reducing airplane accelerations due to atmospheric gusts. For two gust shapes, one gust velocity, one forward velocity, and one wing loading, a series of flights was made with the flap locked and was then repeated with the flap free to operate. The records were evaluated by routine methods. The results indicate that the flap reduced the maximum acceleration increment 39 percent for a severe gust but with a representative gust shape (a sharp-edge gust), the reduction was only 3 percent" (p. 1).

The problem of determining values of structural damping for use in flutter calculations is discussed. The concept of equivalent viscous damping is reviewed and its relation to the structural damping coefficient g introduced in NACA Technical Report No. 685 is shown. The theory of normal modes is reviewed and a number of methods are described for separating the motions associated with different modes. Equations are developed for use in evaluating the damping parameters from experimental data. Experimental results of measurements of damping in several flutter models are presented.

"The vortex theory as presented by the author in earlier papers has been extended to permit the solution of the following problems: (1) the investigation of the relation between thrusts and torque distribution and energy loss as given by the induction of helical vortex sheets and by the parasite drag; (2) the checking of the theorem of Betz of the rigidly behaving helical vortex sheet of minimum induced energy loss; (3) the extension of the theory of the screw propeller of minimum energy loss for the inclusion of parasite-drag distribution along the blades" (p. 1).

"A total of 183 panel specimens of 24ST aluminum alloy with nominal thickness of 0.020, and 0.040 inch with extruded bulb-angle sections of 12 shapes spaced 4 and 5 inches as stiffeners were tested to obtain the buckling stress and the amplitude of the maximum wave when buckled. Bulb angles from 3 to 27 1/2 inches long were tested as pin-end columns. The experimental data are presented as stress-strain and column curves and in tabular form" (p. 1).

"The magnitude, the direction, and the fluctuations of tow forces exerted upon gliders by towing them aloft behind an automobile were measured under a variety of conditions covering a range from gentle to severe types of operation. For these tests, the glider towing force did not exceed 1.6 of the gross weight of the glider. V-G records obtained during the towed-flight period as well as during the subsequent return glide to earth showed accelerations in the range from 3 to -1 g. The results of preliminary airplane tow tests are also presented" (p. 1).

A new method of studying the flow of the water along the bottom of a model of a flying-boat hull is described. In this method, the model is fitted with a transparent bottom and is divided down the center line by a bulkhead. The flow is observed and photographed through one-half of the model by means of the diffused illumination from a battery of lamps contained in the other half of the model. Photographs of the flow, particularly of the changes that occur when the step ventilates, are shown. The results of the present investigation indicate that the method has considerable promise, chiefly in connection with motion-picture studies.

Report presenting testing of a model of the two-stroke engine described in NACA Technical Note No. 674 for the purpose of observing the scavenging-air flow obtained with various inlet-port arrangements. Three types of cylinder head were tried with the round-edge piston in the engine. Results regarding the effect of port arrangement, pistons, cylinder-head shapes, effect of swirl, and exhaust restrictions are provided.

"An investigation of three methods for the prevention and the removal of ice on an airplane windshield has been completed. The methods were: electric heating; hot-air heating; and an alcohol-dispensing, rotating wiper blade. The results showed that vision through the airplane windshield could be maintained during severe icing conditions by the use of heat" (p. 1).

An investigation was made of a large-chord NACA 23030 airfoil with a 40- and a 25.66 percent-chord slotted flap to determine the section aerodynamic characteristics of the airfoil affected by flap chord, slot shape, flap position, and flap deflection. The flap positions for maximum lift, the position for minimum drag at moderate and high lift coefficients, and the complete section aerodynamic characteristics of selected optimum arrangements are given. Envelope polar of various flap arrangements are included. The relative merits of slotted flaps of different chords on the NACA 23030 airfoil are discussed, and a comparison is made of each flap size with a corresponding flap size on the NACA 23021 and 23012 airfoils.

"A full-scale investigation has been conducted to determine the effect of various factors on the shimmy of castering wheels. The factors considered were the geometric arrangement, the tire types, the variations of load, the spindle moment of inertia, and the tire inflation. A comparison of the results of the present investigation with those calculated from existing theory was made" (p. 1).

Report presenting a model of a hypothetical canard airplane, which was designed to be of the same size and general aerodynamic characteristics of a Boeing B-247 airplane in the gust tunnel at one wing loading, one forward speed, one gust velocity, and three gust gradients.

From Summary: "The force variation along the wing span under combined normal and angular accelerations is considered. Non dimensional curves of section load, shear, and moment are given for: (1) the air load that produces a normal acceleration; (2) the accompanying wing weight and normal inertia loads; (3) aileron and gust air loads that produce angular acceleration; (4) the angular inertia load of the wing. The required aerodynamic load distributions have been obtained by use of wing theory, and the wing inertia distributions are based on an analysis of wing-weight data. Several examples are included to illustrate the effect of wing taper and aileron span on the total shears and moments at any section along the span."

"The flow of a compressible fluid past a sphere fixed in a uniform stream is calculated to the third order of approximation by means of the Janzen-Rayleigh method. The velocity and the pressure distribution over the surface of the sphere are computed and the terms involving the fourth power of the Mach number, neglected in Rayleigh's calculation, are shown to be of considerable importance as the local velocity of sound is approached on the sphere. The critical Mach number, that is, the value of the Mach number at which the maximum velocity of the fluid past the sphere is just equal to the local velocity of sound, is calculated for both the second and the third approximation and is found to be, respectively, Mcr=0.587 and Mcr=0.573" (p. 1).

Pressure-distribution tests of an NACA 0009 airfoil with an 80-percent-chord plain flap and three plain tabs, having chord of 10, 20, and 30 percent of the flap chord, were made. Section data suitable for application to the design of horizontal and vertical tail surfaces were obtained. Resultant-pressure diagrams for the airfoil with the flap and the 20-percent-chord tab are presented. Plots are also given of increments of normal-force and hinge-moment coefficients for the airfoil, the flap, and the three tabs. A comparison of some characteristic slopes for the 30-, the 50-, and the 80-percent-chord flaps, tested in the general investigation of plain flaps for control surfaces, is included. Section aerodynamic and load data have been made available for a wide range of flap and a tab chords to be used on an NACA 0009 airfoil or on other conventional sections.

From Summary: "Pressure-distribution tests of an NACA 0009 airfoil with a 30-percent-chord plain flap and three plain tabs, having chords 10, 20, and 30 percent of the flap chord, were made. The purpose of these tests was to continue an investigation to supply structural and aerodynamic section data that may be applied to the design of horizontal and vertical tail surfaces. The results are presented as diagrams of resultant pressures and of resultant-pressure increments for the airfoil with the flap and the 20-percent-chord tab. Increments of normal-force and hinge-moment coefficients for the airfoil, the flap, and the three tabs are also given. At all unstalled flap and tab deflections, the experimental distributions agree well with those calculated by an analytical method. The agreement is poor, however, then the stalled or the unstalled condition of the flap or tab deflected alone was changed to an unstalled or stalled condition by the simultaneous deflection of both the flap and the tab."

Aerodynamic force tests of an NACA 23018 airfoil with a Gwinn flap having a chord 25 percent of the overall chord and of an NACA 23015 airfoil with a plain flap having a 25-percent chord were conducted to determine the relative merits of the Gwinn and the plain flaps. The tests indicated that, based on speed-range ratios, the plain flap was more effective than the Gwinn flap. At small flap deflections, the plain flap had lower drag coefficients at lift-coefficient values less than 0.70. For lift coefficients greater than 0.70, however, the Gwinn flap at all downward flap deflections had the lower drag coefficients.

From Summary: "As a preliminary step in an investigation of control-stick vibration in direct-control autogiros, the periodic variations in the moments transmitted through the control system of a YG-1B autogiro were recorded in flight. The results of the measurements are presented in the form of coefficients of Fourier series expressing the varying part of the lateral and the longitudinal moments acting between rotor and fuselage at the control trunnions. The most important component of the variation in stick force was found to have frequency of three times the rotor speed and an amplitude that rose from negligible values at tip-speed ratio below 0.20 to +/-5.2 pounds longitudinally and +/-3.2 pounds laterally at tip-speed ratios of 0.35. Variations in stick force at all other frequencies were small in comparison with those at three times the rotor speed."

"A method that makes use of thermocouples has been developed to measure the temperature of engine pistons operating at high speeds. The thermocouples installed on the moving piston are connected with a potentiometer outside the engine by means of pneumatically operated plungers, which make contact with the piston thermocouples for about 10 crankshaft degrees at the bottom of the piston stroke. The equipment is operated satisfactory at engine speeds of 2,400 r.p.m. and shows promise of successful operation at higher engine speeds" (p. 1).

From Summary: "Data are presented to show the effects of inlet-air pressure, inlet-air temperature, and compression ratio on the maximum permissible performance obtained with having a hemispherical-dome combustion chamber. The five aircraft-engine fuels used have octane numbers varying from 90 to 100 plus 2 ml of tetraethyl lead per gallon. The data were obtained on a 5 1/4-inch by 4 3/4-inch liquid-cooled engine operating at 2,500 r.p.m. The compression ratio was varied from 6.0 to 8.9. The inlet-air temperature was varied from 110 to 310 F. For each set of conditions, the inlet-air pressure was increased until audible knock occurred and then reduced 2 inches of mercury before data were recorded."

Six 100-octane and two 87-octane aviation engine fuels were tested in a modified C.F.R. variable-compression engine at 1,500, 2,000 and 2,500 rpm. The mixture temperature was raised from 50 to 300 F in approximately 50 degree steps and, at each temperature, the compression ratio was adjusted to give incipient knock as shown by a cathode ray indicator. The results are presented in tabular form. The results are analyzed on the assumption that the conditions which determine whether a given fuel will knock are the maximum values of density and temperature reached by the burning gases. A maximum permissible density factor, proportional to the maximum density of the burning gases just prior to incipient knock, and the temperature of the burning gases at that time were computed for each of the test conditions. Values of the density factors were plotted against the corresponding end-gas temperatures for the three engine speeds and also against engine speed for several and end-gas temperatures. The maximum permissible density factor varied only slightly with engine speed but decreased rapidly with an increase in the end-gas temperature. The effect of changing the mixture temperature was different for fuels of different types. The results emphasize the desirability of …