From Summary: "Section characteristics for use in wing design are presented for the NACA 23012 airfoil with plain and split flaps of 20 percent wing chord at a value of the effective Reynolds number of about 8,000,000. The flap deflections covered a range from 60 degrees upward to 75 degrees downward for the plain flap and from neutral to 90 degrees downward for the split flap. The split flap was aerodynamically superior to the plain flap in producing high maximum lift coefficients and in having lower profile-drag coefficients at high lift coefficients."

From Summary: "Two improvements have been made in the method developed in NACA Reports nos. 487 and 591 for the estimation of the inflow velocity required to overcome a given decelerating torque in an autogiro rotor. At low tip-speed ratios, where the assumptions necessary for the analytical integrations of the earlier papers are valid, the expressions therein derived are greatly simplified by combining and eliminating terms with a view of minimizing the numerical computations required. At high tip-speed ratios, by means of charts based on graphical integrations, errors inherent in the assumptions associated with the analytical method are largely eliminated."

"The present paper reports on experiments made to determine the buckling load under shear of circular curved tension-field webs. The buckling load of the webs may be expressed with reference to the buckling load of the stiffeners. It is found that within the explored range the buckling load is approximately twice as great as that of the identically stiffened flat wall of equal web depth" (p. 1).

"To investigate the laws of flow of compressible fluids in pipes, tests were carried out with air flowing at velocities below and above that of sound in straight smooth pipes. Air was chosen as the flow medium. In order that the effect of compressibility may be brought out most effectively, the velocity should lie between 100 and 500 m/s (200 and 1,000 mph); that is, be of the order of magnitude of the velocity of sound in air. The behavior of the compression shock in a smooth cylindrical pipe was also investigated" (p. 1).

"A flight investigation was made of the increase in effectiveness of ailerons that can be obtained by preventing flow of air through the wing at the hinges and of the possibility of reducing the aileron operating force by replacing ailerons having normal open hinge gaps with narrower but equally effective ailerons having sealed hinge gaps. Tests were made with a Fairchild 22 airplane with two sizes of plain unbalanced ailerons, one set having a chord equal to 0.18c, and the other chord equal to 0.09c. The results of the investigation show that improvement of the lateral-control effectiveness is obtained by completely preventing the flow of air through the wing at the hinge axis of conventional ailerons" (p. 1).

An optically recording engine-pressure indicator of simple and rugged construction has been developed for use in high-pressure and high temperature combustion research. This instrument is of the diaphragm type and has a natural frequency of about 10,000 cycles per second.

The present article describes the application of the results of airfoil theory to hydrofoils and planing surfaces with consideration of the boundary conditions of the free upper surface.

Three rectangular monoplane wings having rounded tips were tested on the N.A.C.A. spinning balance in the 5-foot vertical wind tunnel. The airfoil sections used were the N.A.C.A. 0009, 23018, and 6718. The aerodynamic characteristics of the models and a prediction of the angles of sideslip for steady spins are given. There is included an estimate of the yawing moment that must be furnished by parts of the airplane to balance the inertia couples and wing yawing moments for spinning equilibrium. The predicted angles of sideslip and yawing moments required for spinning equilibrium for a Clark Y wing with the same form are included for comparison.

"At the ends of a monocoque fuselage concentrated axial forces in the skin must generally be taken up. Such axial forces must also be taken up in the case of other members where axial forces from the neighboring stressed skin construction must be considered. In order to take up these axial forces two bulkheads or reinforcing frames may be arranged at the positions where the forces are applied" (p. 1).

"An investigation was conducted in the NACA 20-foot wind tunnel of the ramming effect of three general types of carburetor intake rams for radial engines, namely, the internal constant area type, the external constant area type, and the external expanding type. The rams were installed on a radial air- cooled engine nacelle, and tests were made with and without the propeller operating. The results indicated that the external types having entrances near the front of the engine cowling gave the greatest ramming effect" (p. 1).