Circular presenting a description of the Kay 331 gyroplane, which is an all-metal single-seater with a Pobjoy R engine. A description of the propeller, control, fuselage, tail, flight characteristics, specifications, drawings, and photographs are provided.

"This report is the fifth of a series giving the results obtained from wind tunnel tests on the interference drag and propulsive efficiency of nacelle-propeller-wing combinations. This report gives results of tests of an NACA cowled air-cooled engine nacelle with tractor propeller located in 12 positions with reference to a Clark Y biplane cellule" (p. 603).

This report presents an extension of the autogiro theory of Glauert and Lock in which the influence of a pitch varying with the blade radius is evaluated and methods of approximating the effect of blade tip losses and the influence of reversed velocities on the retreating blades are developed. A comparison of calculated and experimental results showed that most of the rotor characteristics could be calculated with reasonable accuracy, and that the type of induced flow assumed has a secondary effect upon the net rotor forces, although the flapping motion is influenced appreciably. An approximate evaluation of the effect of parasite drag on the rotor blades established the importance of including this factor in the analysis.

This report is the fourth of a series giving the results obtained from wind tunnel tests to determine the interference lift and drag and propulsive efficiency of wing-nacelle-propeller combinations. Previous reports give the results of tests with tractor propellers with various forms of nacelles and engine cowlings. This report gives the results of tests of tandem arrangements of engines and propellers in 11 positions with reference to a thick wing.

"The investigation of the effect of mass distribution on the spinning of airplanes initiated with tests on the NY-1 airplane has been continued by tests on another airplane in order to increase the scope of the information and to observe particularly the behavior of an airplane that shows considerable change in sideslip angle for its various conditions of spinning. The XN2Y-1 naval training biplane was used for the present tests in which changes of ballast along the longitudinal and lateral axes and changes of aileron, stabilizer, and elevator settings were made. The effects of these changes on the steady spin were measured in flight' (p. 185).

From Summary: "The purpose of this report is to make the complicated processes on the direct-lift propeller amenable to analysis and observation. This is accomplished by placing the physical phenomena, starting with the most elementary process, in the foreground, while limiting the mathematical treatment to the most essential in view of the fundamental defects of the theorems. Comparison with model experiments supplements and corroborates the theoretical results."

From Summary: "A comparatively simple method of calculating length of take-off run is developed from the assumption of a linear variation in net accelerating force with air speed and it is shown that the error involved is negligible. Detailed instructions are given for application of the formula and for the calculation of all factors involved."

"The ignition lag of a fuel oil in the combustion chamber of a high speed compression-ignition engine was measured by three different methods. The start of injection of the fuel as observed with a Stoborama was taken as the start of the period of ignition lag in all cases. The end of the period of ignition lag was determined by observation of the appearance of incandescence in the combustion chamber, by inspection of a pressure-time card for evidence of pressure rise, and by analysis of the indicator card for evidence of the combustion of a small but definite quantity of fuel" (p. 1).

From Summary: "Data obtained at the N.A.C.A. tank from tests on the models of three flying-boat hulls - N.A.C.A. models 11-A, 16, and 22 - are used to demonstrate the effect of trim angle on water resistance. A specific example is taken, and data from Model 11-A are used to show that the trim angle giving the minimum water resistance will give minimum total air-plus-water resistance. Total-resistance curves for best trimmed angles and other angles are compared for the same example."

This reports presents a method of calculating time and gross load for take-off of seaplanes and flying boats.

The viewpoints are discussed, according to which the scavenging of two-stroke-cycle engines can be evaluated, and the relations between scavenging pressure and the quantity of the scavenging medium required, as also between the scavenging pressure and the revolution speed, are developed. It is further shown that the power increase is limited by the scavenging process, so that further researches are desirable for qualitative improvement. These results lead to several conclusions regarding the propulsion of motor vehicles by the two-stroke-cycle engines.

"This paper contains a series of calculations showing how the performance of controllable propellers may be derived from data on fixed-pitch propellers given in N.A.C.A. Technical Report No. 350, or from similar data. Sample calculations are given which compare the performance of airplanes with fixed-pitch and with controllable propellers. The gain in performance with controllable propellers is shown to be largely due to the increased power available, rather than to an increase in efficiency" (p. 1).

A general description of the small DVL wind tunnel is provided, with emphasis on air conduction, blower and velocity regulation, velocity measurement, and balance and model suspension.

Three tapered airfoils based on the N.A.C.A. 2200, the N.A.C.A.-M6, and the Clark Y sections were tested in the variable-density wind tunnel at a Reynolds Number of approximately 3,100,000. The models, which were of aspect ratio 6, had constant core center sections and rounded tips, and tapered in thickness from 18 percent at the roots to 9 percent at the tips. The aerodynamic characteristics are given by the usual dimensionless coefficients plotted for both positive and negative angles of attack and by effective profile-drag coefficients plotted against lift coefficients.

"This report gives the results of measurements of the lift, drag, and propeller characteristics of several wing and nacelle combinations with a tractor propeller" (p. 1). The liquid-cooled engines appeared to have an advantage over the air-cooled engines.

From Summary: "This report presents the results of maneuverability tests of an O3U-1 observation airplane. This investigation is the third in a series of similar investigations requested by the Bureau of Aeronautics (Navy) for the purpose of comparing the maneuverability of different airplane types and to provide quantitative data for use in establishing a criterion or method for rating the maneuverability of an airplane. The two former investigations were conducted with the fighter types designated F6C-3 and F6C-4 and have been reported previously. Measurement of the air speed, the angular velocity, the linear acceleration, and positions of the controls were made during abrupt single-control maneuvers with three stop positions for each control, during steady horizontal turns for the determination of minimum radius, and during 180 degree turns by various methods."

Circular presenting a description of the De Havilland Dragon Moth, or D.H. 84, which is the first twin-engine airplane built by this particular company. Details of the design, components, flight characteristics, performance, drawings, and photographs are provided.

This report describes a device for arbitrary enlargement of the gliding angle of airplanes, especially of such with flat gliding angle and difficult landing characteristics. The D.V.L. gliding angle control (design, Hubner) permits a local interruption of the lift distribution along the span and consequently an increased induced drag. The mechanism comprises two wing rudders operated by lever from the pilot's cockpit. Said rudders are fitted on the top side of the wing near the leading edge. The displacement of these rudders results in a separation of the air flow on the top side of the wing.

"The static stresses of airplane parts, the magnitude of which can be determined with the aid of static load assumptions, are mostly superposed by dynamic stresses, the magnitude of which has been but little explored. The object of the present investigation is to show how the strength of airplane parts can best be tested with respect to dynamic stresses with and without superposed static loading, and to what extent the dynamic strength of the parts depends on their structural design. Experimental apparatus and evaluation methods were developed and tried for the execution of vibration-strength tests with entire structural parts both with and without superposed static loading" (p. 1).

An investigation of the possibility of using thrust augmented jets as prime movers was carried out. The augmentation was to be effected by allowing the jet to mix with the surrounding air in the presence of bodies which deflect the air set in motion by the jet. Six augmentation schemes were tested experimentally with compressed air at room temperature at jet speeds up to 1240 feet per second.

The quantity of air which the disk area described by propeller blades travels through, is accelerated rearward conformably to the momentum of the forces acting on the propeller. The accelerated air mass forms behind the propeller the so-called slipstream, in which among others, the mean velocity of advance is increased. If the propeller axis slopes toward the relative flight direction, the slipstream direction likewise changes, i.e., it sets up a downwash behind the propeller.

Ailerons described in references 1, 2, and 3, are summarized in the form of empirical equations which relate the aileron dimensions and displacements to the rolling, yawing, and hinge moments for pitch angles of 0 and 12 degrees, corresponding to angles of attack of the wings of 4 and 16 degrees, respectively.

Tests were made with ordinary ailerons and different sizes of spoilers on rectangular Clark Y wing models with Handley Page tip and full span slots. The tests showed the effect of the control devices on the general performance of the wings as well as on the lateral control and lateral stability characteristics.

This report presents charts which reduce the stress analysis of circular and elliptic rings of uniform cross section subjected to balanced systems of concentrated loads from a statically indeterminate problem to a statically determinate one. To demonstrate the use of the charts in the stress analysis of elliptic rings, an illustrative problem is included.