Corporate income and excess-profits tax return of 1938 for Texas Cotton Industries. The return includes all necessary schedules. The franchise tax return and capital stock tax returns are also attached with their respective schedules and financial statements.

"Static thrust and power measurements were made of six full-scale propellers. The propellers were mounted in front of a liquid-cooled-engine nacelle and were tested at 15 different blade angles in the range from -7 1/2 degrees to 35 degrees at 0.75r. The test rig was located outdoors and the tests were made under conditions of approximately zero wind velocity" (p. 85).

"Factors derived from wing theory are presented. By means of these factors, the angle of zero lift, the lift-curve slope, the pitching moment, the aerodynamic-center position, and the induced drag of tapered wings with partial-span flaps may be calculated. The factors are given for wings of aspect ratios 6 and 10 , of taper ratios from 0.25 to 1.00, and with flaps of various length. An example is presented of the method of application of the factors. Fair agreement with experimental results is shown for two wings of different taper ratio having plain flaps of various spacing" (p. 1).

Report presents the results of an investigation of full-scale nose-slot cowlings conducted in the NACA 20-foot wind tunnel to furnish information on the pressure drop available for cooling. Engine conductances from 0 to 0.12 and exit-slot conductances from 0 to 0.30 were covered. Two basic nose shapes were tested to determine the effect of the radius of curvature of the nose contour; the nose shape with the smaller radius of curvature gave the higher pressure drop across the engine. The best axial location of the slot for low-speed operation was found to be in the region of maximum negative pressure for the basic shape for the particular operating condition. The effect of the pressure operating condition on the available cooling pressure is shown.

Experimental report written by an unknown scientist done on lab rats in order to test the Emulsol Corporation's "solvit" product. The tester has come to the conclusion that "solvit" is not dangerous and does not have any harmful consequences. Included are two tables documenting the results of the experiment on the rats.

Report presents the results of an investigation made in the NACA 7 by 10-foot wind tunnel of a large-chord NACA 23012 airfoil with several arrangements of venetian-blind flaps to determine the aerodynamic section characteristics as affected by the over-all flap chord, the chords of the slats used to form the flap, the slat spacing, the number of slats and the position of the flap with respect to the wing. Complete section data are given in the form of graphs for all the combinations tested.

"Flight tests were made to determine the profile-drag coefficients of a portion of the original wing surface of an all-metal airplane and of a portion of the wing made aerodynamically smooth and more nearly fair than the original section. The wing section was approximately the NACA 2414.5. The tests were carried out over a range of airplane speeds giving a maximum Reynolds number of 15,000,000. Tests were also carried out to locate the point of transition from laminar to turbulent boundary layer and to determine the velocity distribution along the upper surface of the wing" (p. 483).

Report presenting an approximate method of computing the induced efficiency of heavily loaded propellers in suitable form for extension to finite number of blades and a comparison of results obtained using the method with the data of the Betz-Helmbold theory for heavily loaded propellers.

"An investigation of the interference associated with tail surfaces added to wing-fuselage combinations was included in the interference program in progress in the NACA variable-density tunnel. The results indicate that, in aerodynamically clean combinations, the increment to the high-speed drag can be estimated from section characteristics within useful limits of accuracy. The interference appears mainly as effects on the downwash angel and as losses in the tail" (p. 1).

The icing hazard can, in most cases, be avoided by correct execution of the flights according to meteorological viewpoints and by meteorologically correct navigation (horizontal and, above all, vertical). The zones of icing hazard are usually narrowly confined. Their location can be ascertained with, in most cases, sufficient accuracy before take-off.

"Pressure-distribution tests were made on the 32-foot whirling arm of the Daniel Guggenheim Airship Institute of a tapered wing to determine the rolling and yawing moments due to an angular velocity in yaw. The model was tested at 0 degree and 5 degrees pitch, -1 degree and 5 degree yaw, and with a full-span flap deflected 60 degrees. The results are given in the form of span load distributions and in calculated moment coefficients" (p. 1).

Report presenting an experiment regarding tank and float venting conditions that exist on diving airplanes undergoing rapid changes in altitude. The results indicated that large pressure differences build up between the outside and inside of tanks and floats on diving airplanes unless the correct size of venting tube is used.

"Three general theories treating the potential flow about an arbitrary wing section are discussed in this report. The first theory treats the method of conformal transformation as laid down by Theodorsen and Garrick; the second is a generalization of Birnbaum's theory for moderately thick airfoils; the third is a general investigation of the complex velocity function with particular reference to the relations first discussed by F. Weinig. The relative merits of the different methods in question are illustrated on a worked-out example and will be published in a subsequent issue of this periodical" (p. 1).

Note discussing the lift of a finite wing including the calculations and constants for each step of the lift. This information is compared against the lift of an infinite wing. From Summary: "Unsteady lift function for wings of finite aspect ratio have been calculated by approximate methods involving corrections of the aerodynamic inertia and of the angle of the infinite wing. The starting lift of the finite wing is found to be only slightly less than that of the infinite wing; whereas the final lift may be considerably less. The calculations indicate that the distribution of lift near the start is similar to the final distribution."

Corporate income and excess-profits tax return of 1937 for Texas Cotton Industries. The return includes all necessary schedules.

From Summary: "Section characteristics for use in wing design are presented for the NACA 23012 airfoil with plain and split flaps of 20 percent wing chord at a value of the effective Reynolds number of about 8,000,000. The flap deflections covered a range from 60 degrees upward to 75 degrees downward for the plain flap and from neutral to 90 degrees downward for the split flap. The split flap was aerodynamically superior to the plain flap in producing high maximum lift coefficients and in having lower profile-drag coefficients at high lift coefficients."

From Summary: "Two improvements have been made in the method developed in NACA Reports nos. 487 and 591 for the estimation of the inflow velocity required to overcome a given decelerating torque in an autogiro rotor. At low tip-speed ratios, where the assumptions necessary for the analytical integrations of the earlier papers are valid, the expressions therein derived are greatly simplified by combining and eliminating terms with a view of minimizing the numerical computations required. At high tip-speed ratios, by means of charts based on graphical integrations, errors inherent in the assumptions associated with the analytical method are largely eliminated."

"The present paper reports on experiments made to determine the buckling load under shear of circular curved tension-field webs. The buckling load of the webs may be expressed with reference to the buckling load of the stiffeners. It is found that within the explored range the buckling load is approximately twice as great as that of the identically stiffened flat wall of equal web depth" (p. 1).

"To investigate the laws of flow of compressible fluids in pipes, tests were carried out with air flowing at velocities below and above that of sound in straight smooth pipes. Air was chosen as the flow medium. In order that the effect of compressibility may be brought out most effectively, the velocity should lie between 100 and 500 m/s (200 and 1,000 mph); that is, be of the order of magnitude of the velocity of sound in air. The behavior of the compression shock in a smooth cylindrical pipe was also investigated" (p. 1).

"A flight investigation was made of the increase in effectiveness of ailerons that can be obtained by preventing flow of air through the wing at the hinges and of the possibility of reducing the aileron operating force by replacing ailerons having normal open hinge gaps with narrower but equally effective ailerons having sealed hinge gaps. Tests were made with a Fairchild 22 airplane with two sizes of plain unbalanced ailerons, one set having a chord equal to 0.18c, and the other chord equal to 0.09c. The results of the investigation show that improvement of the lateral-control effectiveness is obtained by completely preventing the flow of air through the wing at the hinge axis of conventional ailerons" (p. 1).

An optically recording engine-pressure indicator of simple and rugged construction has been developed for use in high-pressure and high temperature combustion research. This instrument is of the diaphragm type and has a natural frequency of about 10,000 cycles per second.

The present article describes the application of the results of airfoil theory to hydrofoils and planing surfaces with consideration of the boundary conditions of the free upper surface.

Three rectangular monoplane wings having rounded tips were tested on the N.A.C.A. spinning balance in the 5-foot vertical wind tunnel. The airfoil sections used were the N.A.C.A. 0009, 23018, and 6718. The aerodynamic characteristics of the models and a prediction of the angles of sideslip for steady spins are given. There is included an estimate of the yawing moment that must be furnished by parts of the airplane to balance the inertia couples and wing yawing moments for spinning equilibrium. The predicted angles of sideslip and yawing moments required for spinning equilibrium for a Clark Y wing with the same form are included for comparison.

"At the ends of a monocoque fuselage concentrated axial forces in the skin must generally be taken up. Such axial forces must also be taken up in the case of other members where axial forces from the neighboring stressed skin construction must be considered. In order to take up these axial forces two bulkheads or reinforcing frames may be arranged at the positions where the forces are applied" (p. 1).