Report discusses several types of accelerometers and how they function. Methods for reducing error and determining the source of the error, including the best placement for the device, are included.

Report discussing some of the issues regarding the design and operation of helicopters and the theoretical basis behind them. Some particular issues covered include propeller blade design, helicopters in forced descent, horizontal travel, and stability and control.

Given here are the rules officially adopted by the Aeronautical Commission of the Aero Club of France for a flight competition to be held in France in 1920 at the Villacoublay Aerodrome. The prize will be awarded to the pilot who succeeds in obtaining the highest maximum and lowest minimum speeds, and in landing within the shortest distance.

Reports of tests of a Daimler IVa engine at the test-bench at Friedrichshafen, show that the decrease of power of that engine, at high altitudes, was established, and that the manner of its working when air is supplied at a certain pressure was explained. These tests were preparatory to the installation of compressors in giant aircraft for the purpose of maintaining constant power at high altitudes.

An overview is given of experience with geared propeller drives for aviation engines. The development of gear wheels is discussed with emphasis upon bending stresses, compressive stresses, heating, and precision in manufacturing. With respect to the general arrangement of gear drives for airplanes, some principal rules of mechanical engineering that apply with special force are noted.

"In terminating the study of the adaptation of the engine to the airplane, we will examine the problem of the turbo-compressor, the first realization of which dates from the war; this will form an addition to the indications already given on supercharging at various altitudes. This subject is of great importance for the application of the turbo-compressor worked by the exhaust gases. Assuming that the increase of pressure in the admission manifold is the same in both cases, the pressure in the exhaust manifold would be greater in the case in which the compressor is worked by the exhaust gas and there would result a certain reduction of engine power which we must be able to calculate" (p. 1).

By comparing airplanes of known strength that have resisted all the usual and even extreme air loads with those that under like conditions were found to be insufficiently strong, the researchers, aided by scientific investigations, developed standards which are satisfactory for the calculation of airplane structures. Given here are standards applicable to loads on wing trusses, load factors for use in stress analysis, load factors required in sand testing, loads on control surfaces, loads on wing ribs, loads on landing gear, and rigidity of materials.

Methods and equipment for recording small and sometimes rapid motions by photographic means are described, and the efficacy of photographic recording in such instances is evaluated. The optical system consisting of the light source, the mirror or prism for transmitting motion to the emergent beam, and a means of bringing the rays into focus on the film are discussed. Attention is given to the critical issue of mirror mounting.

Given here are the results of experiments conducted by Colonel Costanzi of the Italian Army to determine the influence of the surrounding building in which a wind tunnel was installed on the efficiency of the installation, and how the efficiency of the installation was affected by the design of the tunnel. Also given are the results of a series of experiments by Eiffel on 34 models of tunnels of different dimensions. This series of experiments was started in order to find out if, by changing the shape of the nozzle or of the diffuser of the large tunnel at Auteuil, the efficiency of the installation could be improved.

An attempt was made to determine the effect of spindle interference on the lift of the airfoil by measuring moments about the axis parallel to the direction of air flow. The values obtained are of the same degree as the experimental error, and for the present this effect will be neglected. The results obtained using a U.S.A. 15 wing (plotted here) show that the correction is nearly constant from 0 degrees to 10 degrees incidence and that at greater angles its value becomes erratic. At such angles, however, the wing drag is so high that the spindle correction and its attendant errors become relatively small and unimportant.

The construction of giant airplanes was begun in Germany in August, 1914. The tables annexed here show that a large number of airplanes weighing up to 15.5 tons were constructed and tested in Germany during the War, and it is certain that no other country turned out airplanes of this weight nor in such large numbers. An examination of the tables shows that by the end of the War all the manufacturers had arrived at a well-defined type, namely an airplane of about 12 tons with four engines of 260 horsepower each. The aircraft listed here are discussed with regard to useful weight and aerodynamic qualities.

Given here is a description of the design of a scientific recording wind tunnel balance. It was decided that the most satisfactory arrangement would be a rigid ring completely surrounding the tunnel or wind stream, so that the model could be supported from it by wires or any arrangement of spindles. The forces and moments acting on this ring can then be recorded by suitable weighing apparatus. The methods available for recording forces on the arms are explained. The proposed type of balance will support the model rigidly in a variety of ways, will make a complete test without attention, and will plot the results so that all computations are avoided.

The construction of the dynamometer hub is illustrated and explained, and its electrical and aviation motor tests, as well as those in free flight, described.

A new empirical formula was developed that holds good for any length and any material of a rod, and agrees well with the results of extensive strength tests. To facilitate calculations, three tables are included, giving the crippling load for solid and hollow sectioned wooden rods of different thickness and length, as well as for steel tubes manufactured according to the standards of Army Air Services Inspection. Further, a graphical method of calculation of the breaking load is derived in which a single curve is employed for determination of the allowable fiber stress.

Given here are the results of a test conducted in a wind tunnel on the performance of a vane-driven gear pump used to pump gasoline upward into a small tank located within the upper wing from which it flows by gravity to the engine carburetor. Information is given on the efficiency of the pump, the head resistance of the vanes, the performance and characteristics of the unit with and without housing about the vanes, the pump performance when motor driven, and resistance and power characteristics.

The author argues that because of a general misunderstanding of the principles of flight at low speed, there are a large number of airplanes that could be made to fly several miles per hour slower than at present by making slight modifications. In order to show how greatly the wing section affects the minimum speed, curves are plotted against various loadings. The disposition of wings on the airplane slightly affects the lift coefficient, and a few such cases are discussed.

Note presenting the physical properties which may be demanded of fuels for aviation use and the means that may be adopted by the engine manufacturers to properly meet the demands necessitated by the use of the fuel. Some of the factors that must be considered include its composition, the quantity available, the price per heat unit, and the possibility of keeping stocks in aerial ports both at home and abroad.

From Summary: "The author, who was a captain of the Reserves in the Technical Department of the Aviation Division (Board of Airplane Experts) during the war, shows what means were taken for the creation of new airplane types and what tests were employed for trying out their flying properties, capacities and structural reliability. The principal representative types of each of the classes of airplanes are described and the characteristics of the important structural parts are discussed. Data regarding the number of airplanes at the front and the flying efficiency of the various classes of airplanes are given."

It was a conclusion of this detailed study of the practicality of using airships for carrying passengers that, although slow, airships are capable of carrying useful loads over long distances. However, it is noted that there is a certain limit to the advantages of large cubature. Beyond a certain point, the maximum altitude of the airship goes on decreasing, in spite of the fact that the range of action in the horizontal plane and the useful load go on increasing. The possibility of rapid climb is an essential factor of security in aerial navigation in the case of storms, as is velocity.

The Caproni Company recently built a seaplane of unusual design. The main supporting surfaces consisted of three triplanes in tandem, the lower wings being attached to the hull, which was described as providing accommodation for a hundred passengers. On one of the first flights, the seaplane fell into a lake, nose down, and was destroyed. The authors wish to show that this failure could have been predicted.

Given here is a brief review of the fundamental principles of the propeller slip-stream theory and its further development through later researches, which demonstrate the connection between the propeller slip-stream theory and Frounde's so-called 'propeller blade theory.' The propeller slip-stream theory, especially in its improved form, now gives us the basis for determining the mutual influence of the parts of the blade, so that, in calculating the shape of the blade, we can get along with certain section characteristics, which have been determined once and for all. It is argued that new theories present the possibility of investigating the phenomena in the vicinity of the propeller, allowing us to calculate its action on the basis of fewer experimental values.

Thus far, all attempts at the quantitative determination of drag, on the basis of the theory of viscous fluids, have met with but slight success. For this reason, whenever a more accurate knowledge of the drag is desirable, it must be determined by experiment. Here, a few experimental results are given on the drag of a cylinder exposed to a stream of air at right angles to its axis. It is shown that the drag depends on the absolute dimensions of the body and the velocity and viscosity of the fluid in a much more complex manner than has heretofore been supposed.

From Summary: "The difficulties experienced in properly holding thin tipped or tapered airfoils while testing on an N.P.L. type aerodynamic balance even at low air speeds, and the impossibility of holding even solid metal models at the high speeds attainable at the National Advisory Committee's wind tunnel, necessitated the design of a balance which would hold model airfoils of any thickness and at speeds up to 150 m.p.h. In addition to mechanical strength and rigidity, it was highly desirable that the balance readings should require a minimum amount of correction and mathematical manipulation in order to obtain the lift and drag coefficients and the center of pressure. The balance described herein is similar to one in use at the University of Gottingen, the main difference lying in the addition of a device for reading the center of pressure directly, without the necessity of any correction whatsoever. Details of the design and operation of the device are given."

From Introduction: "A model of the F-5-L seaplane was made, verified, and tested at 40 miles an hour in the 8' x 8' tunnel for lift and drag, also for pitching, yawing and rolling moments. Subsequently, the yawing moment test was repeated with a modified fin. The results are reported without VL scale correction."