Given here is a description of the design of a scientific recording wind tunnel balance. It was decided that the most satisfactory arrangement would be a rigid ring completely surrounding the tunnel or wind stream, so that the model could be supported from it by wires or any arrangement of spindles. The forces and moments acting on this ring can then be recorded by suitable weighing apparatus. The methods available for recording forces on the arms are explained. The proposed type of balance will support the model rigidly in a variety of ways, will make a complete test without attention, and will plot the results so that all computations are avoided.

Described here is a method by which high average fuel economy has been achieved in aircraft engines. Details are given of the design of certain foreign engines that employ an unusual type of fuel-air ratio control in which the change in power produced by a mixture change is due almost entirely to the change in the power producing ability of the unit weight of the mixture. The safety and performance features of this type of control are explained.

With the advent of the V type engine, a new method to measure the clearance volume in cylinders was needed. It was suggested that this measurement could be made by a process which consisted essentially of simultaneously changing both a known and unknown volume of gas by a known amount and then calculating the magnitude of the unknown from the resulting difference in pressure between the two. An instrument based on this design is described.

The construction of giant airplanes was begun in Germany in August, 1914. The tables annexed here show that a large number of airplanes weighing up to 15.5 tons were constructed and tested in Germany during the War, and it is certain that no other country turned out airplanes of this weight nor in such large numbers. An examination of the tables shows that by the end of the War all the manufacturers had arrived at a well-defined type, namely an airplane of about 12 tons with four engines of 260 horsepower each. The aircraft listed here are discussed with regard to useful weight and aerodynamic qualities.

Technical notes discussing the steadiness factor in engines and the calculations that can be used to arrive at it. Factors affecting the steadiness factor are detailed, including the mass of parts, torque, engine rotation, and power.

Fan brakes used as absorption dynamometers in testing internal combustion engines have the disadvantage that a given fan will run only at one speed when the engine is delivering full power. In order to be able to vary the speed at which a given power will be absorbed, English manufacturers have for some time been using a cylindrical housing around the fan with one or two variable openings in the periphery. Here, results are given of tests conducted to determine how great a range of speed can be obtained from such a device.

Report discusses the theory of inflow of the propeller and the fact that both suctional axial velocity and suctional tangential velocity must be considered when calculating the maximum efficiency.

Given here is a brief description of the Göttingen wind tunnel for the testing of aircraft models, preceded by a history of its development. Included are a number of diagrams illustrating, among other things, a sectional elevation of the wind tunnel, the pressure regulator, the entrance cone and method of supporting a model for simple drag tests, a three-component balance, and a propeller testing device, all of which are discussed in the text.

Note presenting an examination of horizontal buoyancy in wind tunnels, including an examination of the relative flow, static pressure gradient, horizontal buoyancy computation, and methods of computation in practical use are provided.

Given here are the results of experiments conducted by Colonel Costanzi of the Italian Army to determine the influence of the surrounding building in which a wind tunnel was installed on the efficiency of the installation, and how the efficiency of the installation was affected by the design of the tunnel. Also given are the results of a series of experiments by Eiffel on 34 models of tunnels of different dimensions. This series of experiments was started in order to find out if, by changing the shape of the nozzle or of the diffuser of the large tunnel at Auteuil, the efficiency of the installation could be improved.

Methods and equipment for recording small and sometimes rapid motions by photographic means are described, and the efficacy of photographic recording in such instances is evaluated. The optical system consisting of the light source, the mirror or prism for transmitting motion to the emergent beam, and a means of bringing the rays into focus on the film are discussed. Attention is given to the critical issue of mirror mounting.

Given here are the rules officially adopted by the Aeronautical Commission of the Aero Club of France for a flight competition to be held in France in 1920 at the Villacoublay Aerodrome. The prize will be awarded to the pilot who succeeds in obtaining the highest maximum and lowest minimum speeds, and in landing within the shortest distance.

Reports of tests of a Daimler IVa engine at the test-bench at Friedrichshafen, show that the decrease of power of that engine, at high altitudes, was established, and that the manner of its working when air is supplied at a certain pressure was explained. These tests were preparatory to the installation of compressors in giant aircraft for the purpose of maintaining constant power at high altitudes.

Discussed here are computations of drag or negative traction of geared down supporting propellers in the downward vertical glide of a helicopter. By means of Frounde's Theory, the maximum value of the drag of a windmill is calculated. For wooden propellers, the author finds that the difference between the drag and the weight is proportional to the number of blades and is larger for propellers of small diameter; thus it is 25 kg. for a six blade propeller with a diameter of 2 m. 50.

The construction of the dynamometer hub is illustrated and explained, and its electrical and aviation motor tests, as well as those in free flight, described.

An overview is given of experience with geared propeller drives for aviation engines. The development of gear wheels is discussed with emphasis upon bending stresses, compressive stresses, heating, and precision in manufacturing. With respect to the general arrangement of gear drives for airplanes, some principal rules of mechanical engineering that apply with special force are noted.

It became evident during World War I that ever-increasing demands were being placed on the mean power of aircraft engines as a result of the increased on board equipment and the demands of aerial combat. The need was for increased climbing efficiency and climbing speed. The response to these demands has been in terms of lightweight construction and the adaptation of the aircraft engine to the requirements of its use.

Report discusses the calculations that can be used to show why pressures inside an engine during preignition are higher than average. This information can be used to design a safer engine that is able to contain the increased pressure and heat generated during preignition.

"In terminating the study of the adaptation of the engine to the airplane, we will examine the problem of the turbo-compressor, the first realization of which dates from the war; this will form an addition to the indications already given on supercharging at various altitudes. This subject is of great importance for the application of the turbo-compressor worked by the exhaust gases. Assuming that the increase of pressure in the admission manifold is the same in both cases, the pressure in the exhaust manifold would be greater in the case in which the compressor is worked by the exhaust gas and there would result a certain reduction of engine power which we must be able to calculate" (p. 1).

Report discusses information obtained from studying large birds that fly by soaring, which involves using the wind without moving their wings. An Egyptian vulture and African white-backed vulture were observed and their relative air speed, upward air velocity, lift, and drag were noted. The experimental methods for measuring these values are described.

A mathematical model is presented towards a theory of lifting and resistance on wings. It consists hide of a theory of multiplanes, conditions of flow at a great distance from the wing, lifting systems of minimum resistance, and free stream and stream limited by walls.

Various properties of duralumin as used in aircraft construction are discussed, including the effects of temperature, working, tempering, and strength.

The author discusses the limited benefits of supercharging motors and some of the factors that make supercharging less beneficial than it initially appears.

Static tests fall into two groups, the first of which is designed to load all members of the structure approximately in accordance with the worst loads which they carry in flight, while the second is directed to the testing of specific members which are suspected of weakness and which are difficult to analyze mathematically. The nature of the loading in the second type is different for every different test, but the purpose of the first is defined clearly enough to permit the adoption of some standard set of loading specifications, at least for airplanes of normal design. Here, an attempt is made to carry through an analysis leading to such a standard, the goal being the determination of a load which will simultaneously impose on every member of the airplane structure a stress equal to the worst it will carry in flight.