In this document, simple modes are used to demonstrate the importance of different material effects on predicted material behavior. This document should help one understand the basic assumptions made in stress analysis.

The effects of variables on the rate of Purex solvent deterioration were investigated with the emphasis on those deterioration products which cannot be removed by carbonate washing. The deterioration rate was found to be directly proportional to the acid and nitrate ion concentrations, and proportional to the square root of the concentration of nitrite ion. Other observations on the effects of temperature, relative merits of brand name solvents, and the effects of radiation are included. A method of calculating the equilibrium level of the solvent deterioration products based on study conclusions and various estimates is outlined.

Metallographic examination of an irradiated powder metal uranium slug from PT-313-105-4M⁽¹⁾ was undertaken primarily as an evaluation of recently remotized metallographic equipment. It was, also, proposed to compare the grain size with values obtained ultrasonically on the same slug. It was further proposed to make a comparison, so far as limited data permitted, of post-irradiated powder metal uranium grain size with that to be expected from normal uranium similarly irradiated.

A study of the fabrication failures for zirconium and zircaloy-2 process tubes was made. In the tube reducing operation, a non-uniform reduction in area for the cross section was found to be a major cause of failure. In annealing studies, a cycle of 2 hours at 820 deg C in vacuum followed by furnace cooling produced the greatest ductility of extruded zircaloy-2 for the annealing treatments studied. The ductility of cold worked and annealed zircaloy-2 was found to be superior to that of extruded and annealed material. The strain rate of a cold working process was found to affect the ductility of zircaloy-2.

The absorption of the important fission products by plants is quantitatively presented as a concentration factor which is defined as the ratio of the fission product concentration found in the leaves to the fission product concentration found in the nutrient substrate. Of the fission products, the isotopes of strontium were found to be the most important by virtue of their high concentration factor, long half-life, and low maximum permissible amounts for animals. Iodine and barium follow in importance, with cesium moderately important in some soils. All other fission products have concentration factors less than strontium by 100 or more. The effect on the concentration factor of different agricultural plants, as well as different organs of the same plant, causes variations of about a factor of ten or less for each isotope. The concentration factor tends to increase as the pH of the nutrient substrate is decreased. Addition of stable carrier to the substrate does not decrease the amount of the radioactive isotope that is absorbed into the plant. The presence of iodine and yttrium carrier actually causes a significant increase in the concentration of the respective radioactive isotopes in the plant tissue.

This report is a survey of methods for determining trace amounts of nitric oxide and nitrogen dioxide in air. The methods are evaluated in relation to their applicability to continuous monitoring procedures for these substances in stack gas and in air for human consumption.

The purpose of this paper is to examine the theory and results of chemical exchange experiments for separation of heavy metal isotopes. The aim is to find a means of predicting those chemical exchange systems likely to produce large isotopic separation factors.

This report describes the evaluation of physical properties of AGHT and 185-W graphites that are important to pile construction and operation. On the basis of these data, purified AGHT graphite was allocated to either filler block positions in the central regions of the K piles or to the upper or lower reflectors. This decision was based on the similarities of physical properties between AGHT graphite and the other moderator components. A similar allocation could be made for 185-W graphite for some future pile if it can be successfully purified or if purification is not required.

A large (size 2) Purex pulse generator was installed in the 321 Building Tan Farm to pulse solutions in the prototype Purex HA Column. Flow sheet considerations indicated a need for information on leakage rates with various size weep holes in the pulse generator piston. In addition to leakage tests, experiments were conducted to determine the air required under the piston to hold the column contents away from the pulse generator piston thereby preventing leakage during shut down and the determine the time required to bleed the air trapped in the pulse leg when the column is first filled. [...] Leakage past the piston was not appreciably affected by pulse frequency. [..] Bleeding the air out of the pulse leg under start-up conditions, even with the piston weep hole plugged, was rapid. The longest time required to bleed the pulse leg was 36 minutes, which included a column-filling time of 30 minutes.

A knowledge of the mechanical and physical properties of uranium is important in understanding and explaining its pile behavior. The effects of irradiation on the properties of uranium will be dealt with in another chapter. However, it is important to know and understand the pre-irradiation properties of uranium prior to investigating the effects of irradiation.

The erection of a concrete biological shield at Hanford, Washington presented several unique construction problems. This shield encloses the radioactive core of a reactor and is designed to protect operating personnel from the harmful effects of pile neutrons and associated gamma radiation. Permanent steel forms were erected to close tolerance around the reactor and filled with high density concrete by means of prepacked method. Prefabricated sections of the steel forms, or crates, were five to eight feet deep and weighed up to 18 tons each. During erection, the process holes through successive crates were kept within 0.012 in. of their nominal distance. The left side, top shield, and right side of this biological shield were constructed integrally to form a rigid frame. The front and rear crates, which contain numerous process holes, were keyed into the side and top shields so as to permit relative expansions of shield components and to provide for their lateral support. These massive steel and concrete walls provide considerable resistance to blast and earthquake forces, support numerous process facilities, contain pile gas, as well as protect personnel from nuclear radiation.

Two methods for calculating the *reduction in η due to spectral hardening have been used. In the first method it is assumed that the absorption cross section of U-238 is l/v. This indicates no change in η within the error of the calculation. In the second it is assumed that the scattering cross section of uranium is constant. A decrease in η of 3.0% at the centerline of the slug is indicated by this calculation. The assumption U-238 is a l/v absorber is regarded as the most reasonable of the two.

The purpose of this report is to present the information obtained relative to the characteristic adsorption of radioisotopes in a long (forty feet) laboratory soil column treated with a high salt, process waste of high activity density. The movement of adsorbed cations in a soil column subjected to prolonged leeching by water also was determined.