Report issued by the Office of Saline Water over studies conducted on the reverse-osmosis program. The methods of desalination through osmosis are discussed. This report includes tables, illustrations, and photographs.

The objective is to establish, from test results, the relationship between pressure loss and orifice configuration, mass rate, and steam quality, for a Fuel Cycle fuel assembly.

The major portion of transfers and inventory in the Chemical Processing Department are dependent on volume measurement. Good volume measurements are therefore essential to good SS material control. Considerable attention has been given to the volume problem especially on primary transfer points. Document HW-57888 discusses the biasing effect pf temperature on manometer oil. HW- 57866 given the procedure for vessel calibration. Other undocumented correspondence has discussed recent calibrations and certain aspects of temperature considerations in the volume determinations. However, there is a need to document for future reference the consideration given temperature and provide at the same time information which covers the temperature angle on all volume methods used in the Chemical Processing Department.

The fire involved approximately 30 liters of isopropyl alcohol as a result of the ignition of about 16-18 liters of isopropyl alcohol and a slurry of thoria and ammonium nitrate in a 20-liter glass carboy. This material was undergoing a volume reduction by boiling in a floor-type metal hood with Plexiglas sides and 3 sliding door on the front of ordinary glass. The alcohol vapor was vents directly into the hood (Fig1.)

A full-scale turbojet engine was operated with pentaborane fuel continuously for 22 minutes at conditions simulating flight at a Mach number of 0.8 at an altitude of 50,000 feet. This period of operation is approximately three times longer than previously reported operation times. Although the specific fuel consumption was reduced from 1.3 with JP-4 fuel to 0.98 with pentaborane, a 13.2-percent reduction in net thrust was also encountered. A portion of this thrust loss is potentially recoverable with proper design of the engine components. The boron oxide deposition and erosion processes within the engine approached an equilibrium condition after approximately 22 minutes of operation with pentaborane.

Report presenting a flight-test program investigating a modification to an interceptor system. Results indicate that a significant improvement in the overall response characteristics of the system. The modification minimizes the interaction between the antenna and interceptor motions, which can have a serious influence on flight path stability during a lead-collision attack.

Report presenting an evaluation of a 1/4-sector of an annular combustor designed for use with pentaborane fuel at a simulated altitude condition. Results regarding the pentaborane performance, combustor development, and the JP-5 fuel performance are provided.

Report presenting a blade-vibration and rotating-stall survey on a modified version of a production turbojet engine with a 13-stage axial-flow compressor with a design pressure ratio of 7 and an air flow of 120 pounds per second. This testing was carried out due to the problems rotating stall can cause with both experimental and production axial-flow compressors. Results regarding the rotating-stall patterns, rotor-blade vibrations, radial and axial strength of rotating stall, and maximum rotating-stall speed are provided.

Report presenting the effect of adjusting compressor inlet-guide-vane angle on overall compressor performance, stage performance, engine thrust, and specific fuel consumption in a 7000-pound-thrust turbojet engine. Data was obtained at several angles and demonstrated that increasing the guide-vane angle decreased the weight flow at the higher compressor speeds. It had no effect on stage performance other than at the first stage, where it reduced maximum flow, pressure, and temperature coefficients.

Report discussing methods, advantages, and disadvantages of locating rotating heat exchangers ahead of, within, and behind the main engine compressor. Heat rejection should occur at the compressor discharge for best engine performance. Results regarding turbojet-engine performance, turboprop-engine performance, and a comparison of engine performance with liquid- and air-cooling are provided.

The Redox process uses or produces only a very few materials that are hazardous for reasons other than radioactivity. The conditions under which these materials become hazardous were carefully taken into consideration in the development of the process and design of the equipment. A considerable about of information on the hazardous properties of the process materials was obtained so that the pertinent material could be incorporated into the process specifications. Providing the equipment is operating properly and the process is being carried out within specification limits, no hazardous conditions can be created by the process. The purpose of this report is to assemble in a single, readily available document all of the information on the normal concentration limits and safe handling procedures needed to adequately control the use and storage of these materials. This report should be helpful in preparing safety bulletins and provide guidance in case of unusual incidents, malfunctioning of equipment, or contemplated changes in either the process or equipment. It is important to remember that a maximum allowable concentration (MAC) is only a limit on the concentration of a toxic material which cannot be exceeded in the air to which workers are constantly exposed to every working …

Report presenting a highly loaded transonic rotor which was designed, built, and tested as part of a two-stage counterrotating-compressor research program. The design conditions were chosen to explore the upper limits of loading and Mach number for the transonic unit. The complete rotor design procedure is presented as well as the recorded stall traces and techniques for obtaining the data.

Abstract: "The measurement of large, high-frequency, short-pulse currents--ordinarily complicated by inductance, stray magnetic fields, and magnetic forces that tend to disassemble the measuring device--is simplified and made with an average error of 2-1/2% by the use of a specially developed noninductive radial shunt in conjuntion with an oscilloscope. The skin-effect correction is derived theoretically and the accuracy of the method is demonstrated."

"The transient motion in angles of attack and sideslip during a constant rolling maneuver has been analyzed. Simplified expressions are presented for the determination of the pertinent modes of motion as well as the modal coefficient corresponding to each mode. Calculations made with and without the derivatives for side force due to sideslip and lift-curve slope indicate that although these derivatives increase the total damping of the system they do not markedly affect the transient motion" (p. 131).

Report presenting a J47-25 engine instrumented with thermocouples and operated under steady-state and transient-conditions in an altitude test stand to determine the operating temperatures at altitude in the turbine section of a turbojet engine. Results regarding the temperature effects and transient operation are provided.

Report describing a method of fitting "a weighted least square polynomial of order n to a set of m observation points" in order "to satisfy the need for a general curve fitting scheme" (p. 1).

From abstract: General expressions relating product stream compositions to the operating conditions of countercurrent stagewise extraction columns are derived by an inductive method, and the conversion of the general equations to ones involving the particular case of constant extraction factor is demonstrated. For comparison, the derivation of simple column equations by the use of finite difference equations is included.

The decontamination of portable instruments by the Calibration Unit has presented a problem for some time. Most of the contamination is in the 100 to 500 c/m or 500 to 2000 d/m range. Higher levels of contamination can usually be reduced to these levels, but further cleaning proves quite difficult

Report presenting combustion-efficiency data for a 5-inch ramjet-type combustor using a simple V-gutter flame holder. Data for homogeneous fuel-air mixtures of 14 pure fuels and 3 fuel blends cover a range of inlet static pressures and velocities.

Motion pictures at camera speeds up to 3000 frames per second were taken of the combustion of liquid oxygen and gasoline in a 100-pound thrust rocket engine. The effect of seven methods of propellant injection on the uniformity of combustion was investigated. The flame front was generally found to extend to the injector faces and all the injection systems showed considerable nonuniformity of combustion. Pressure vibration records indicated combustion vibrations that corresponded to resonant-chamber frequencies.

Report presenting an investigation to determine the static longitudinal stability and control characteristics of a tailless wing-body combination with a pointed wing of aspect ratio 2 and trailing-edge elevons. The effectiveness of inset tabs in reducing the elevon hinge moment was also determined. Results regarding the lift, drag, pitching moment, elevon hinge moment, tab hinge moment, elevon load, and center of pressure of elevon load are provided.

This report presents "Results of a critical literature review on pressure drop due to isothermal turbulent flow in noncircular geometries" (introduction).

Memorandum presenting an investigation of a 2:1 area ratio conical diffuser of length equal to the inlet diameter with separate variation of several basic parameters for simple nontwisted counterrotating rectangular vortex generators over a considerable range of inlet-boundary-layer thickness. The maximum values of static-pressure rise were determined for angle of attack, spacing, aspect ratio, and span-to-inlet boundary-layer thickness. Results for the diffuser with no vortex generators, effects of selectable vortex-generator variables, effect of inlet-boundary-layer displacement thickness, and use of the maximum indicated vortex-generator design values are provided.

In solving the two-group, two medium equations for neutron diffusion in a finite one-dimensional multiplying system, the equations in each medium can be solved, and the boundary conditions used to determine the coefficients. This direct attack involves eight simultaneous linear equations. The opportunities for error are numerous, and, frequently, a great deal of accuracy is lost by subtractions; hence, it is felt that an alternative method of solution, in which numerical errors would be less likely to occur, would be desirable.