The Yakima Species Interactions Study (YSIS) was begun in September of 1989 to investigate species interactions among fish in response to proposed supplementation of salmon and steelhead in the Yakima Basin. Supplementation is defined as ''the use of artificial propagation in the attempt to maintain or increase natural production while maintaining the long term fitness of the target population, and keeping the ecological and genetic impacts on non-target populations within specified biological limits'' (BPA summary report series, 1992). Target populations are the populations of fish that will be supplemented and non-target populations are all other populations of fish. One of the goals of the proposed Yakima Fisheries Project (YFP) is to test the strategy of supplementation in the Yakima Basin. In a review of published literature and unpublished projects about supplementation, Miller et al. (1990) concluded ''Adverse impacts to wild stocks have been shown or postulated for about every type of hatchery fish introduction where the intent was to rebuild runs''. In Steward and Bjornn's (1990) review of the published literature, they stated that ''Genetic and ecological effects, and changes in productivity of the native stocks that can result from supplementation remain largely unmeasured''. Uncertainties about the effects supplementation in …

Burlington Bottoms, consisting of approximately 417 acres of riparian and wetland habitat, was purchased by the Bonneville Power Administration in November 1991. The site is located approximately 1/2 mile north of the Sauvie Island Bridge (T2N R1W Sections 20, 21), and is bound on the east side by Multnomah Channel and on the west side by the Burlington Northern Railroad right-of-way and U.S. Highway 30 (Figures 1 and 2). Wildlife habitat values resulting from the purchase of this site will contribute toward the goal of mitigating for habitat lost as outlined in the Columbia and Willamette River Basin's Fish and Wildlife Program and Amendments. Under this Program, mitigation goals were developed as a result of the loss of wildlife habitat due to the development and operation of Federal hydro-electric facilities in the Columbia and Willamette River Basins. In 1993, an interdisciplinary team was formed to develop and implement quantitative Habitat Evaluation Procedures (HEP) to document the value of various habitats at Burlington Bottoms. Results of the HEP will be used to: (1) determine the current status and habitat enhancement potential of the site consistent with wildlife mitigation goals and objectives; and (2) develop a management plan for the area. HEP …

Biodiesel produces fewer pollutants than petroleum diesel, and is virtually free of sulfur. These properties make biodiesel an attractive candidate to facilitate compliance with the Clean Air Act Amendments of 1990 (CAAA). This fuel is ordinarily considered to be derived from oilseeds, but an essentially identical biodiesel can be made from microalgae.

Radiation therapy with hadron beams now has a 40-year track record at many accelerator laboratories around the world, essentially all of these originally physics-research oriented. The great promise shown for treating cancer has led the medical community to seek dedicated accelerator facilities in a hospital setting, where more rapid progress can be made in clinical research. This paper will discuss accelerator and beam characteristics relevant to hadron therapy, particularly as applied to hospital-based facilities. A survey of currently-operating and planned hadron therapy facilities will be given, with particular emphasis on Lorna Linda (the first dedicated proton facility in a hospital) and HIMAC (the first dedicated heavy-ion medical facility).

Inclusive jet cross-sections have been measured in {bar p}p collisions at {radical}s = 546 and 1,800 GeV, using the CDF detector at the Fermilab Tevatron. The ratio of low E{sub t} (25--75 GeV) jet cross sections vs. E{sub t} has been formed, and the authors have used this as a tool to investigate some implications of the published 1989 CDF ``jet scaling`` results. In particular, results at 1,800 GeV have given no indication of any unsuspected errors in CDF`s low E{sub t} jet measurements.

The alloy CuPt is one of the few that order into a L1{sub 1} crystal structure, i.e. planes of copper and planes of planes of planes of platinum perpendicular to the < 111 > direction. For disordered CuPt, the calculated Warren-Cowley short-range order parameter indicates an instability to concentration fluctuations with a wave-vector of ({1/2}, {1/2}, {1/2}), consistent with L1{sub 1} ordering. We show that this rare tendency is due to this ordering vector arising from the large joint density of states associated with L point and X point van-Hove singularities which lie near the Fermi energy.

Laser pointing instability adds to the error of slope measurements taken with the Long Trace Profiler (LTP). As with carriage pitch error, this laser pointing error must be accounted for and subtracted from the surface under test (SUT) slope measurement. In the past, a separate reference beam (REF) allowed characterization of the component of slope error from carriage pitch. However, the component of slope error from laser pointing manifests itself differently in the SUT measured slope. An analysis of angle error propagation is given, and the effect of these errors on measured slope is determined. Then a method is proposed for identifying these errors and subtracting them from the measured SUT slope function. Separate measurements of carriage pitch and laser pointing instability isolate these effects, so that the effectiveness of the error identification algorithm may be demonstrated.

This work provides a brief overview of past and ongoing efforts at Lawrence Livermore National Laboratory (LLNL) in the area of finite-element modeling of crash and impact problems. The process has been one of evolution in several respects. One aspect of the evolution has been the continual upgrading and refinement of the DYNA, NIKE, and TOPAZ family of finite-element codes. The major missions of these codes involve problems where the dominant factors are high-rate dynamics, quasi-statics, and heat transfer, respectively. However, analysis of a total event, whether it be a shipping container drop or an automobile/barrier collision, may require use or coupling or two or more of these codes. Along with refinements in speed, contact capability, and element technology, material model complexity continues to evolve as more detail is demanded from the analyses. A more recent evolution has involved the mix of problems addressed at LLNL and the direction of the technology thrusts. A pronounced increase in collaborative efforts with the civilian and private sector has resulted in a mix of complex problems involving synergism between weapons applications (shipping container, earth penetrator, missile carrier, ship hull damage) and a more broad base of problems such as vehicle impacts as discussed …

The purpose of this Environmental Assessment (EA) is to review the possible environmental consequences associated with the construction and operation of a Health Protection Instrument Calibration Facility on the Savannah River Site (SRS). The proposed replacement calibration facility would be located in B Area of SRS and would replace an inadequate existing facility currently located within A Area of SRS (Building 736-A). The new facility would provide laboratories, offices, test equipment and the support space necessary for the SRS Radiation Monitoring Instrument Calibration Program to comply with DOE Orders 5480.4 (Environmental Protection, Safety and Health Protection Standards) and 5480.11 (Radiation Protection for Occupational Workers). The proposed facility would serve as the central site source for the evaluation, selection, inspection, testing, calibration, and maintenance of all SRS radiation monitoring instrumentation. The proposed facility would be constructed on a currently undeveloped portion in B Area of SRS. The exact plot associated with the proposed action is a 1.2 hectare (3 acre) tract of land located on the west side of SRS Road No. 2. The proposed facility would lie approximately 4.4 km (2.75 mi) from the nearest SRS site boundary. The proposed facility would also lie within the confines of the existing …

Several years ago, in response to growing concern about global climate change, the US National Climatic Data Center and the Carbon Dioxide Information Analysis Center undertook an effort to create a baseline global land surface climate data set called the Global Historical Climatology Network (GHCN, Vose et al., 1992). GHCN was created by merging several large existing climate data sets into one data base. Fifteen separate data sets went into the creation of the GHCN version 1.0. GHCN version 1.0 was released in 1992. It has 7,533 precipitation stations, but the number of stations varies with time. A slight majority (55%) have records in excess of 50 years, and a significant proportion (13%) have records in excess of 100 years. The longest period of record for any given station is 291 years (1697--1987 for Kew, United Kingdom).

This report presents research objectives, discusses activities, and presents technical progress for the period April 1, 1993 through June 31, 1993 on Contract No. DE-FC21-86LC11084 with the Department of Energy, Laramie Project Office. The scope of the research program and the continuation is to study interacting hydrologic, geotechnical, and chemical factors affecting the behavior and disposal of combusted processed oil shale. The research combines bench-scale testing with large scale research sufficient to describe commercial scale embankment behavior. The large scale approach was accomplished by establishing five lysimeters, each 7.3 {times} 3.0 {times} 3.0 m deep, filled with processed oil shale that has been retorted and combusted by the Lurgi-Ruhrgas (Lurgi) process. Approximately 400 tons of Lurgi processed oil shale waste was provided by Rio Blanco Oil Shale Co., Inc. (RBOSC) through a separate cooperative agreement with the University of Wyoming (UW) to carry out this study. Three of the lysimeters were established at the RBOSC Tract C-a in the Piceance Basin of Colorado. Two lysimeters were established in the Environmental Simulation Laboratory (ESL) at UW. The ESL was specifically designed and constructed so that a large range of climatic conditions could be physically applied to the processed oil shale which …

The objective of the exchange between Pacific Northwest Laboratory (PNL) and Finnigan Corporation is a transfer of expertise and technology for the design and operation of efficient and sensitive atmospheric pressure/vacuum electrospray ionization (ESI) sources. The development of such ion sources will permit wider application of mass spectrometry instrumentation in applied studies in a variety of disciplines including clinical, forensic, biochemical, biotechnical, and environmental studies where sensitivity is a paramount concern. Two meetings were held between representatives of Finnigan Corporation (led by Dr. Ian Jardine, Director for Marketing, Finnigan Corporation) and PNL staff members. During these meetings, Finnigan and PNL staff surveyed the existing technology for atmosphere/vacuum interface of mass spectrometry to ESI. The representatives from Finnigan viewed demonstrations of recent developments that increased efficiency and sensitivity for ESI mass spectrometry. During these meetings, knowledge and expertise were shared in the development of instrumentation, methods, and applications of ESI mass spectrometry with particular emphasis on current and planned Finnigan instrumentation. With the objective of more effective and competitive products for Finnigan Corporation, concepts for a Cooperative Research and Development Agreement (CRADA) were directed toward the development and commercialization of advanced high efficiency and sensitivity ESI technology. A detailed proposal and …

Radioactive waste is stored in 149 3,785 m{sup 3} (million gal) single-shell tanks on the US Department of Energy`s Hanford Reservation in eastern Washington. To minimize leakage as the tanks age, the free liquid has been pumped out, leaving concentrated solidified salt cake and sludge deposits. Now methods to dislodge and remove this waste are being developed so that the waste can be retrieved and processed for permanent storage. This paper presents research and development on ultrahigh-pressure water-jet technology to fracture and dislodge the wastes in these tanks. A water-based prototype scarifier with an integral conveyance system is being developed, and its performance demonstrated in a coupled analytical and experimental investigation. This paper describes experimental objectives and approach and results of the single jet experiments. Previous testing indicates that the method can be readily applied to salt cake waste forms; retrieval and conveyance of sludge and viscous fluid waste forms may present additional challenges.

This report investigates two secondary materials, plastic lumber made from mixed plastic waste, and cement blocks and structures made with incinerator ash. Engineering properties, environmental impacts, and energy costs and savings of these secondary materials are compared to standard lumber products and cement blocks. Market capacity and social acceptance of plastic lumber and stabilized ash products are analyzed. These secondary materials apparently have potential markets; however, their economic value is primarily that they will not take up landfill space. For plastic lumber and stabilized incinerator ash products, marine and highway construction seem ideal public works applications. Incinerator ash may be suitable to use in seawalls, jetties, fishing reefs, highway barriers, and roadbed applications. Docks, piers, highway sound barriers, parking stops, and park furniture may all be made from plastic lumber. To encourage public acceptance and improve the market potential of secondary materials, these activities could be beneficial: industry should emphasize developing useful, long-lived products; industry and governments should create product performance criteria; government should provide rigorous testing and demonstration programs; and government and industry should cooperate to improve public outreach and educational programs.

Key technical and strategic choices are reviewed, leading to the fabrication method of ion-milled grating grooves for the monochromators at the Advanced Light Source (ALS) at Lawrence Berkeley Laboratory (LBL), and for other synchrotrons. Several laboratories and their industrial partners have joined to manufacture gratings with essentially theoretical performance. Metrology -data and theoretical comparisons are given for square wave profile grating samples ion-milled into electroless nickel surfaces. The extensive capabilities of Hughes Aircraft in grating manufacture are reviewed.

This report is the official inventory for radioactive waste stored in underground tanks in the 200 in the 200 Areas at the Hanford Site. Data that depict the status of stored radioactive waste and tank vessel integrity are contained within the report. This report provides data on each of the existing 177 large underground waste storage tanks and 49 smaller catch tanks and special surveillance facilities, and supplemental information regarding tank surveillance anomalies and ongoing investigations.

Microwave discharges (2.45 GHz) have been generated in C{sub 60}-containing Ar produced by flowing Ar over fullerene-containing soot. Optical spectroscopy shows that the spectrum is dominated by the d{sup 3}{Pi}g-a{sup 3}{Pi}u Swan bands of C{sub 2} and particularly the {Delta}v = {minus}2, {minus}1, 0, +1, and +2 sequences. These results give direct evidence that C{sub 2} is one of the products of C{sub 60} fragmentation brought about, at least in part, by collisionally induced dissociation (CID). C{sub 60} has been used as a precursor in a plasma-enhanced chemical vapor deposition (PECVD) experiment to grow diamond-thin films. The films, grown in an Ar/H{sub 2} gas mixture (0.14% carbon content, 100 Torr, 20 sccm Ar, 4 sccm H{sub 2}, 1500 W, 850{degree}C substrate temperature), were characterized with SEM, XRD, and Raman spectroscopy. Growth rate was found to be {approx} 0.6 {mu}/hr. Assuming a linear dependence on carbon concentration, a growth rate at least six times higher than commonly observed using methane as a precursor, would be predicted at a carbon content of 1% based on C{sub 60}. Energetic and mechanistic arguments are advanced to rationalize this result based on C{sub 2} as the growth species.

Many of the in-core components in pressurized water reactors are constructed of austenitic stainless steels. The potential behavior of these components can be predicted using data on similar steels irradiated at much higher displacement rates in liquid-metal reactors or water-cooled mixed-spectrum reactors. Consideration of the differences between the pressurized water environment and that of the other reactors leads to the conclusion that significant amounts of void swelling, irradiation creep, and embrittlement will occur in some components, and that the level of damage per atomic displacement may be larger in the pressurized water environment.

Two methods are commonly used to measure water content of geologic materials by neutron diffusion, the moisture gauge and the neutron log. Both are used at NTS, the moisture gauge in tunnels, the neutron log in vertical drilled holes. In this work, the moisture gauge and the neutron log are compared for use in air-filled holes NTS. The measurement instruments have evolved with very different operational characteristics and one important physics difference, the source to detector spacing. The moisture gauge has a very short, 0--6 cm spacing, with little internal shielding, and count increases with water. The neutron log has a long spacing, 30--50 cm, substantial internal shielding, and exhibits decreasing count with increasing water. The moisture gauge gives better bed resolution than the neutron log. Because its count increases with water, the moisture gauge is more strongly affected by water in the borehole, especially in dry formations. In these conditions the neutron log is the method of choice. In air-filled holes, if source size or logging time is not a constraint, the relative sensitivity of the two tools to water is determined by the relative strengths of borehole effects as fluid, holesize, or tool-wall gap. If source size is …

The overall goal of this project is to improve the effectiveness of single photon emission computed tomography (SPECT) to image and quantify radiolabeled monoclonal antibodies. During the past year, we have made significant progress toward this goal, and this report summarizes that work. Our efforts have been mainly directed along three fronts. First, we have developed and tested new reconstruction methods including three-dimensional iterative algorithms that model non-uniform attenuation and distance-dependent detector response. Both fan beam and parallel beam collimator geometries have been modeled and novel ways of improving the efficiency of the computationally intensive methods have been introduced. Second, an ultra-high resolution, small field-of-view pinhole collimator has been constructed and evaluated. Reconstructed spatial resolution of 1 to 3 mm (FWHM) has been achieved in phantom scans with a useful field-of-view of 9 to 10 cm. Finally, we have investigated the ability of SPECT to image and quantify astatine-211 distributions. Reconstructed images of phantom data demonstrated quantitative accuracy to within 10% with proper attenuation and scatter compensation.

Comparisons are made between grain boundary composition and intergranular stress corrosion cracking (IGSCC) of 304 and 309 austenitic stainless steels in high-temperature water environments. Chromium depletion had the dominant effect on cracking resistance with the extent of IG cracking controlled by the interfacial chromium concentration. The minimum chromium concentration required to promote cracking was a function of the applied strain rate during slow-strain-rate tensile tests in 288 C air-saturated water. Depletion from bulk levels of 18 wt% to {approximately}13.5 wt% Cr at grain boundaries prompted 100% IG cracking at a strain rate of 1 {times} 10{sup {minus}6} s{sup {minus}1}, while embrittlement was observed with only a slight depletion to {approximately}17 wt% at 2 {times} 10{sup {minus}7} s{sup {minus}1}. Insights into critical interfacial compositions promoting IGSCC are discussed in reference to cracking of irradiated stainless steel nuclear reactor core components.

During the past quarter, Tasks 3, 4, 5, and 6 were active. Task 3 Pilot Scale Combustion Testing activity included data analysis of pilot- and bench-scale combustion samples in support of the development of CQE slogging and fouling models. Under Task 4, field testing at the fifth host utility site -- New England Power Service Company`s Brayton Point Unit 3 -- was completed in March with the testing of the alternate coal. Test plans were finalized for the sixth and final field test to be performed at Brayton Point Unit 2 in April 1993. Tasks 5 and 6 activities were directed at design and development of CQE base classes and objects, continued formulation and integration of CQE algorithms and submodels, development of the user interface prototype, and preparation of the Fireside Advisor.

The southern Great Plains (SGP) Cloud and Radiation Testbed (CART) site is designed to help satisfy the data needs of the Atmospheric Radiation Measurement (ARM) Program Science Team. This document defines the scientific priorities for site activities during the six-months beginning on July 1, 1993, and also looks forward in lesser detail to subsequent six-month periods. The primary purpose of this Site Scientific Mission Plan is to provide guidance for the development of plans for site operations. It also provides a planning focus for the ARM Functional Teams (Management Team, Experiment Support Team, Operations Team, Data Management Team, Instrument Team, and Campaign Team), and it serves to disseminate the current plans more generally within the ARM Program and among the Science Team. This document includes a description of the site`s operational status and the primary envisaged site activities, together with information concerning approved and proposed Intensive Observation Periods. Amendments will be prepared and distributed whenever the content changes by more than 30% within a six-month period. The primary users of this document are the site operator, the site scientist, the Science Team through the ARM Program Science Director, the ARM Program Experiment Center, and the aforementioned ARM Program Functional Teams. …

Recent technological developments have opened the possibility to construct a device which we call a Linac Coherent Light Source (LCLS); a fourth generation light source, with brightness, coherence, and peak power far exceeding other sources. Operating on the principle of the free electron laser (FEL), the LCLS would extend the range of FEL operation to much aborter wavelength than the 240 mn that has so far been reached. We report the results of studies of the use of the SLAC linac to drive an LCLS at wavelengths from about 3-100 nm initially and possibly even shorter wavelengths in the future. Lasing would be achieved in a single pass of a low emittance, high peak current, high energy electron beam through a long undulator. Most present FELs use an optical cavity to build up the intensity of the light to achieve lasing action in a low gain oscillator configuration. By eliminating the optical cavity, which is difficult to make at short wavelengths, laser action can be extended to shorter wavelengths by Self-Amplified-Spontaneous-Emission (SASE), or by harmonic generation from a longer wavelength seed laser. Short wavelength, single pass lasers have been extensively studied at several laboratories and at recent workshops.