Optically Stimulated Luminescence (OSL) technology has been pioneered at the Pacific Northwest National Laboratory (PNNL) for applications in personnel radiation dosimetry and commercially has become highly successful in replacing older technologies such as Thermoluminescence Dosimeters (TLDs) and film. OSL phosphors are used to measure radiation exposure by illuminating them with light after ionizing radiation exposure and measuring the amount of light emitted by the OSL phosphor. By using a two-dimensional plate of OSL material and raster scanning a light beam across the OSL plate a radiation pattern or image can be measured. The Arms Control community requires an electrons-free medium to measure the attributes of extent and symmetry on Pu pits in storage containers. OSL technology, used in the two-dimensional imaging mode, provides a means to measure these attributes with exposure times on the order of an hour. A special OSL reader has been built by PNNL to measure OSL imaging plates with a size of 20 cm by 30 cm. The reader uses 10 light emitting diode clusters with 10 corresponding photomultiplier tubes to measure an OSL imaging plate in less than 5 minutes. The resolution of each of the 10 measurement assemblies is 1 square-centimeter. A collimator assembly …

Transmission Electron Microscopy developed from an imagingtool into a quantitative electron beam characterization tool that locallyaccesses structure, chemistry, and bonding in materials with sub Angstromresolution. Experiments utilize coherently and incoherently scatteredelectrons. In this contribution, the interface between gallium nitrideand sapphire as well as thin silicon gate oxides are studied tounderstand underlying physical processes and the strength of thedifferent microscopy techniques. An investigation of the GaN/sapphireinterface benefits largely from the application of phase contrastmicroscopy that makes it possible to visualize dislocation corestructures and single columns of oxygen and nitrogen at a closest spacingof 85 pm. In contrast, it is adequate to investigate Si/SiOxNy/poly-Siinterfaces with incoherently scattered electrons and electronspectroscopy because amorphous and poly crystalline materials areinvolved. Here, it is demonstrated that the SiOxNy/poly-Si interface isrougher than the Si/SiOx interface, that desirable nitrogen diffusiongradients can be introduced into the gate oxide, and that a nitridationcoupled with annealing increases its physical width while reducing theequivalent electrical oxide thickness to values approaching 1.2 nm.Therefore, an amorphous SiNxOy gate dielectric seems to be a suitablesubstitute for traditional gate oxides to further increase device speedby reducing dimensions in Si technology.

Determining and characterizing the effectiveness of run-time optimization techniques is particularly relevant to modern sparse linear algebra software libraries that tend to hide from the user the internal storage format. For instance, a certain storage structure may dictate a particular algorithmic approach. Once a general scheme of access has been found based on a storage structure, one promising idea involves analyzing the sparsity pattern of the matrix operand to find places where the efficient static optimization techniques may be re-used. There are numerous ways in which this can be done, and it is almost certain that there will be no provably best way. In this case, it will also be necessary to search the space of available options during run-time. We have experimented with a variety of techniques for optimizing sparse matrix vector multiplication to take instruction sets, functional units, and memory hierarchies into account on the Power 3 architecture. Sparse matrix-vector multiplication is of course the inner loop in any iterative solver, even multigrid, since it includes all the interpolation, restriction, and smoothing operations. The structural properties of the application leads to sparse matrices that feature a sufficiently regular pattern, so that the automatic optimization techniques already integrated in …

Predictions of airflows around buildings and the associated thermal and dispersion phenomena continue to be challenging because of the presence of extremely heterogeneous surface structures within urban areas. Atmospheric conditions can induce local winds to flow around structures rather than over them. Thus pollutants that are released at or near the ground tend to persist at relatively low levels with only minimal ventilation of the airborne material away from the ground surface. While flow and dispersion phenomena can be studied within wind tunnel settings, recent advances in numerical modeling have enabled computational fluid dynamics (CFD) to evolve into an important tool in the simulation of building scale flows. They are developing numerical models to simulate the flow and dispersion of releases around multi-building complexes. These models will be used to assess the transport and fate of releases of hazardous agents within urban areas and to support emergency response activities. There are already a number of models that have been developed to simulate flow and dispersion around urban settings. A recent collection of these papers can be found in the Proceedings of the International Workshop on CFD for Wind Climate in Cities. Most of the simulation studies presented in the literature …

This document is a collection of the contributions made to the March IIT workshop on an e{sup +}e{sup -} collider in the VLHC tunnel. This machine, which is based on a relatively conservative extrapolation of LEP technology, has a baseline luminosity of 10{sup 33}/cm{sup 2}/s at a CM energy of 370 GeV. The overall parameters and general description of such a machine is described in T. Sen and J. Norem, ''A Very Large Lepton Collider in the VLHC Tunnel'', to be published. A preprint of this paper is included as Appendix 2 of this report. The intention of the workshop was to define the parameters of such a collider and make them available to the community for use in further physics studies. It is clear that the machine cannot compete with a full scale linear collider. Its main interest would be if a VLHC were built and if a linear collider did not already exist. In this case, it could provide a limited and perhaps crucial view of low mass Higgs states. Although the study is incomplete, it does define rather well the parameters of the machine, as well as the challenges that the design faces. The study benefited greatly …

None

An integrating solid state detector with segmentation has been developed that addresses the needs in scanning transmission x-ray microscopy below 1 keV photon energy. The detector is not cooled and can be operated without an entrance window which leads to a total photon detection efficiency close to 100%. The chosen segmentation with 8 independent segments is matched to the geometry of the STXM to maximize image mode flexibility. In the bright field configuration for 1 ms integration time and 520 eV x-rays the rms noise is 8 photons per integration.

None

The promise of inertial fusion energy driven by heavy ion beams requires the development of accelerators that produce ion currents (approx 100's Amperes/beam) and ion energies ({approx} 1 - 10 GeV) that have not been achieved simultaneously in any existing accelerator. The high currents imply high generalized perveances, large tun depressions, and high space charge potentials of the beam center relative to the beam pipe. Many of the scientific issues associated with ion beams of high perveance and large tune depression have been addressed over the last two decades on scaled experiments at Lawrence Berkeley and Lawrence Livermore National Laboratories, the University of Maryland, and elsewhere. The additional requirement of high space charge potential (or equivalently high line charge density) gives rise to effects (particularly the role of electrons in beam transport) which must be understood before proceeding to a large scale accelerator. The first phase of a new series of experiments in the Heavy Ion Fusion Virtual National Laboratory (HIF VNL), the High Current Experiments (HCX), is now beginning at LBNL. The mission of the HCX is to transport beams with driver line charge density so as to investigate the physics of this regime, including constraints on the maximum …

Parallel optical interconnects based on multimode fiber ribbon cables are emerging as a robust, high-performance data link technology that enhances throughput by using parallel arrays of fibers. While this technology has primarily been implemented as single wavelength point-to-point links, it can be significantly enhanced by wavelength division multiplexing (WDM). WDM enables both increased point-to-point bandwidth as well as more complex interconnect topologies and routing approaches that are particularly attractive for massively parallel processing (MPP) systems. Exploiting the advantages of WDM interconnects requires multi-wavelength sources, a low loss routing fabric, and small footprint wavelength selective filter modules. The Lambda-connect project ({gamma}- Connect) at Lawrence Livermore National Laboratory is a technology development and proof-of-principle demonstration of the enabling hardware for WDM parallel optical interconnects for use in massively parallel processing systems and other high-performance data link applications. This dissertation demonstrates several key system components and technologies for {gamma}-Connect.

A model-based detector is developed to process shallow water ocean acoustic data. The function of the detector is to adaptively monitor the environment and decide whether or not a change from normal has occurred. Here we develop a processor incorporating both a normal-mode ocean acoustic model and a vertical hydrophone array. The detector is applied to data acquired from the Hudson Canyon experiments at various ranges and its performance is evaluated.

Properties of rock materials under quasistatic conditions are well characterized in laboratory experiments. Unfortunately, quasistatic data alone are not sufficient to calibrate models for use to describe inelastic wave propagation associated with conventional and nuclear explosions, or with impact. First, rock properties are size-dependent. properties measured using laboratory samples on the order of a few centimeters in size need to be modified to adequately describe wave propagation in a problem on the order of a few hundred meters in size. Second, there is lack of data about the damage (softening) behavior of rock because most laboratory tests focus on the pre-peak hardening region with very little emphasis on the post-peak softening region. This paper presents a model for granite that accounts for both the hardening and softening of geologic materials, and also provides a simple description of rubblized rock. The model is shown to reproduce results of quasistatic triaxial experiments as well as peak velocity and peak displacement attenuation from a compendium of dynamic wave propagation experiments that includes US and French nuclear tests in granite.

A possible D0 Run IIb stave design currently under study is characterized by an outer carbon fiber stiffening shell with the silicon detectors mounted internally and a single central cooling line running between them; in this paper the stave will be analyzed for thermal compatibility since the different coefficient of thermal expansion in the materials may cause unpredictable stresses and strains in the structure. A simplified stave section has been modeled with finite elements for different materials configurations and the vertical and longitudinal displacements induced by the thermal gradient, together with the related stresses, have been computed. Finally, once selected the most suitable material combination, a more realistic model has been created in order to study the influence of the hybrid location along the ladders.

The large strain deformation response of 6061-T6 and Ti-6Al-4V has been evaluated over a range in strain rates from 10{sup -4} s{sup -1} to over 10{sup 4} s{sup -1}. The results have been used to critically evaluate the strength and damage components of the Johnson-Cook (JC) material model. A new model that addresses the shortcomings of the JC model was then developed and evaluated. The model is derived from the rate equations that represent deformation mechanisms active during moderate and high rate loading. Another model that accounts for the influence of void formation on yield and flow behavior of a ductile metal (the Gurson model) was also evaluated. The characteristics and predictive capabilities of these models are reviewed.

When completed, Lawrence Livermore National Laboratory's (LLNL) National Ignition Facility (NIF) will be the world's largest laser with experimental capabilities applicable to stockpile stewardship, energy research, science and astrophysics. As construction of the conventional facilities nears completion, operations supporting the installation of specialized laser equipment have come online. Playing a critical role in the precision cleaning of mechanical parts from the NIF beamline are three pieces of aqueous cleaning equipment. Housed in the Optics Assembly Building (OAB), adjacent to NIF's laser bay, are the large mechanical parts gross cleaner (LMPGC), the large mechanical parts precision cleaner (LMPPC), and the small mechanical parts gross and precision cleaner (SMPGPC). These aqueous units, designed and built by Sonic Systems, Inc., of Newtown, Pennsylvania, not only accommodate parts that vary greatly in size, weight, geometry, surface finish and material, but also produce cleaned parts that meet the stringent NIF cleanliness standards (MIL-STD-1246C Level 83 for particles and A/10 for non-volatile residue). Each unit was designed with extensive water- and energy-conserving features, and the technology used minimizes hazardous waste generation associated with solvent wipe cleaning, the traditional method for cleaning laser mechanical components. The LMPGC provides preliminary gross cleaning for large mechanical parts. Collection, filtration …

Minimally invasive surgery (MIS) is an approach whereby procedures conventionally performed with large and potentially traumatic incisions are replaced by several tiny incisions through which specialized instruments are inserted. Early MIS, often called laparoscopic surgery, used video cameras and laparoscopes to visualize and control the medical devices, which were typically cutting or stapling tools. More recently, catheter-based procedures have become a fast growing sector of all surgeries. In these procedures, small incisions are made into one of the main arteries (e.g. femoral artery in the thigh), and a long thin hollow tube is inserted and positioned near the target area. The key advantage of this technique is that recovery time can be reduced from months to a matter of days. In the United States, over 700,000 catheter procedures are performed annually representing a market of over $350 million. Further growth in this area will require significant improvements in the current catheter technology. In order to effectively navigate a catheter through the tortuous vessels of the body, two capabilities must exist: imaging and positioning. In most cases, catheter procedures rely on radiography for visualization and manual manipulation for positioning of the device. Radiography provides two-dimensional, global images of the vasculature and …

This document presents the findings of a technology market assessment for thermal energy storage (TES) in space cooling applications. The potential impact of TES in Federal facilities is modeled using the Federal building inventory with the appropriate climatic and energy cost data. In addition, this assessment identified acceptance issues and major obstacles through interviews with energy services companies (ESCOs), TES manufacturers, and Federal facility staff.

Recent work in classification indicates that significant improvements in accuracy can be obtained by growing an ensemble of classifiers and having them vote for the most popular class. This paper focuses on ensembles of decision trees that are created with a randomized procedure based on sampling. Randomization can be introduced by using random samples of the training data (as in bagging or boosting) and running a conventional tree-building algorithm, or by randomizing the induction algorithm itself. The objective of this paper is to describe the first experiences with a novel randomized tree induction method that uses a sub-sample of instances at a node to determine the split. The empirical results show that ensembles generated using this approach yield results that are competitive in accuracy and superior in computational cost to boosting and bagging.

Lake Roosevelt has been stocked with Whatcom stock kokanee since 1989 to mitigate for anadromous salmon losses caused by the construction of Grand Coulee Dam. The primary objective of the hatchery plantings was to create a self-sustaining recreational fishery. Due to low return numbers, it was hypothesized a native stock of kokanee might perform better than the coastal Whatcom strain. Therefore, kokanee from Meadow Creek, a tributary of Kootenay Lake, British Columbia were selected as an alternative stock. Matched pair releases of Whatcom stock and Meadow Creek kokanee were made from Sherman Creek in late June 2000. Stock performance between Lake Whatcom and Meadow Creek kokanee was evaluated through three performance measures (1) returns to Sherman Creek, the primary egg collection facility, (2) returns to other tributaries, indicating availability for angler harvest, and (3) returns to the creel. A secondary objective was to evaluate the numbers collected at downstream fish passage facilities. Age 2 kokanee were collected during five passes through the reservoir, which included 89 tributaries between August 17th and November 7th, 2000. Sherman Creek was sampled once a week because it was the primary egg collection location. A total of 2,789 age 2 kokanee were collected, in which …

Lake Whatcom stock kokanee have been planted in Lake Roosevelt since 1988 with the primary goal of establishing a self-sustaining fishery. Returns of hatchery kokanee to egg collection facilities and recruitment to the creel have been minimal. Therefore, four experiments were conducted to determine the most appropriate release strategy that would increase kokanee returns. The first experiment compared morpholine and non-morpholine imprinted kokanee return rates, the second experiment compared early and middle run Whatcom kokanee, the third experiment compared early and late release dates, and the fourth experiment compared three net pen release strategies: Sherman Creek hatchery vs. Sherman Creek net pens, Colville River net pens vs. Sherman Creek net pens, and upper vs. lower reservoir net pen releases. Each experiment was tested in three ways: (1) returns to Sherman Creek, (2) returns to other tributaries throughout the reservoir, and (3) returns to the creel. Chi-square analysis of hatchery and tributary returns indicated no significant difference between morpholine imprinted and non-imprinted fish, early run fish outperformed middle run fish, early release date outperformed late release fish, and the hatchery outperformed all net pen releases. Hatchery kokanee harvest was estimated at 3,323 fish, which was 33% of the total harvest. Return …

The sodium bearing tank waste (SBW) at Idaho National Engineering and Environmental Laboratory (INEEL) contains high concentrations of sulfur (roughly 5 mass% of SO3 on a nonvolatile oxide basis). The amount of sulfur that can be feed to the melter will ultimately determine the loading of SBW in glass produced by the baseline (low-temperature, joule-heated, liquid-fed, ceramic-lined) melter. The amount of sulfur which can be fed to the melter is determined by several major factors including: the tolerance of the melter for an immiscible salt layer accumulation, the solubility of sulfur in the glass melt, the fraction of sulfur removed to the off-gas, and the incorporation of sulfur into the glass up to it?s solubility limit. This report summarizes the current status of testing aimed at determining the impacts of key chemical and physical parameters on the partitioning of sulfur between the glass, a molten salt, and the off-gas.

As part of the Leak Detection, Monitoring and Mitigation (LDMM) program conducted by CH2M HILL 105-A during FY 2001. These tests are being conducted to assess the applicability of these methods (Electrical Resistance Tomography [ERT], High Resolution Resistivity [HRR], Cross-Borehole Seismography [XBS], Cross-Borehole Radar [XBR], and Cross-Borehole Electromagnetic Induction [CEMI]) to the detection and measurement of Single Shell Tank (SST) leaks into the vadose zone during planned sluicing operations. The testing in FY 2001 will result in the selection of up to two methods for further testing in FY 2002. In parallel with the geophysical tests, a Partitioning Interwell Tracer Test (PITT) study will be conducted simultaneously at the Mock Tank to assess the effectiveness of this technology in detecting and quantifying tank leaks in the vadose zone. Preparatory and background work using Cone Penetrometer methods (CPT) will be conducted at the Mock Tank site and an adjacent test area to derive soil properties for groundtruthing purposes for all methods.

The objective of this study was to evaluate site-specific effects for early life-stage (eyed eggs to free swimming juveniles) fall chinook salmon that might be exposed to hexavalent chromium from Hanford groundwater sources. Our exposure conditions included hexavalent chromium obtained from Hanford groundwater wells near the Columbia River, Columbia River water as the diluent, and locally adapted populations of fall chinook salmon. This report describes both a 96-hr pretest using rainbow trout eggs and an early life-stage test beginning with chinook salmon eggs.

Natural attenuation processes are commonly used for remediation of contaminated sites. A variety of natural processes occur without human intervention at all sites to varying rates and degrees of effectiveness to attenuate (decrease) the mass, toxicity, mobility, volume, or concentration of organic and inorganic contaminants in soil, groundwater, and surface water systems. The objective of this review is to identify potential technical investments to be incorporated in the Subsurface Contaminant Focus Area Strategic Plan for monitored natural attenuation. When implemented, the technical investments will help evaluate and implement monitored natural attenuation as a remediation option at DOE sites. The outcome of this review is a set of conclusions and general recommendations regarding research needs, programmatic guidance, and stakeholder issues pertaining to monitored natural attenuation for the DOE complex.