This document comprises the Operational Test Report for the 241-AZ-101 Ultrasonic Interface Level Analyzer. The objective of the testing was to verify that all equipment and components functioned as designed following construction completion and turnover to operations.

Title 10 of the United States Code of Federal Regulations Part 71 for the Nuclear Regulatory Commission (10 CFR Part 71.73) requires that Type B radioactive material (RAM) packages satisfy certain Hypothetical Accident Conditions (HAC) thermal design requirements to ensure package safety during accidental fire conditions. Compliance with thermal design requirements can be met by prototype tests, analyses only or a combination of tests and analyses. Normally, it is impractical to meet all the HAC using tests only and the analytical methods are too complex due to the multi-physics non-linear nature of the fire event. Therefore, a combination of tests and thermal analyses methods using commercial heat transfer software are used to meet the necessary design requirements. The authors, along with his other colleagues at Savannah River National Laboratory in Aiken, SC, USA, have successfully used this 'tests and analyses' approach in the design and certification of several United States' DOE/NNSA certified packages, e.g. 9975, 9977, 9978, 9979, H1700, and Bulk Tritium Shipping Package (BTSP). This paper will describe these methods and it is hoped that the RAM Type B package designers and analysts can use them for their applications.

Observation of antiprotons in a propane or hydrogen bubble chamber offers the possiblity of studying several phenomena for which counter or photographic emulsion techniques are less suitable. Because there is a high ratio of pions, muons, and electrons to antiprotons in the available momentum-analyzed beams, these beams cannot be used in the bubble chamber without an initial purification, which increases the ratio of antiprotons to other particles. Such a purification has been achieved by utilizing the difference in rates of momentum loss in absorbers between antiprotons and other particles. The principle of the method is to pass a momentum-analyzed beam through an absorber. Since particles of unequal mass do not have the same specific ionization they lose different amounts of momentum, and a further magnetic deflection suffices to separate the particles physically according to mass. In this experiment a desirable momentum for antiprotons entering the bubble chamber was 684 Mev/c; however, at this momentum the ratio of undesirable particles to antiprotons at the target where they are produced is about 6 x 10{sup 5}. By starting with 970-Mev/c particles at the target and using the method of differential absorption, they decreased the ratio of undesirable particles (87% {mu}{sup -}, 105 …

The construction and initial commissioning phase of a new heavy ion preinjector was completed at Brookhaven in September, 2010, and the preinjector is now operational. This preinjector, using an EBIS source to produce high charge state heavy ions, provided helium and neon ion beams for use at the NASA Space Radiation Laboratory in the Fall of 2010, and gold and uranium beams are being commissioned during the 2011 run cycle for use in RHIC. The EBIS operates with an electron beam current of up to 10 A, to produce mA level currents in 10-40 {micro}s beam pulses. The source is followed by an RFQ and IH linac to accelerate ions with q/m > 0.16 to an energy of 2 MeV/amu, for injection into the Booster synchrotron. The performance of the preinjector is presented, including initial operational experience for the NASA and RHIC programs.

One of the principal tools of industrial ecology is life-cycle assessment which intends to improve overall economic efficiency and to minimize negative environmental impacts of products, processes, and facilities. This paper describes a general methodology for environmentally responsible assessment of these activities; it discusses some of the underlying considerations for this assessment which are accessible by rigorous quantitative analysis; and an overall economic performance metric is proposed which puts both environmental and economic considerations on a common basis. Finally, some considerations involved in this approach is introduced as a guide to environmentally sound design and management.

The convective period leading up to a Type Ia supernova (SNIa) explosion is characterized by very low Mach number flows, requiringhydrodynamical methods well-suited to long-time integration. We continuethe development of the low Mach number equation set for stellar scaleflows by incorporating the effects of heat release due to externalsources. Low Mach number hydrodynamics equations with a time-dependentbackground state are derived, and a numerical method based on theapproximate projection formalism is presented. We demonstrate throughvalidation with a fully compressible hydrodynamics code that this lowMach number model accurately captures the expansion of the stellaratmosphere as well as the local dynamics due to external heat sources.This algorithm provides the basis for an efficient simulation tool forstudying the ignition of SNe Ia.

In two previous reports nucleon-meson cascade calculations were carried out for several cases of interest in the design of the transverse shield for the proposed 45-Bev linear electron accelerator at Stanford University. Results are now given for two additional cases. (auth)

The Machine Protection System (MPS) is a device-safety system that is designed to prevent damage to hardware by generating interlocks, based upon the state of input signals generated by selected sub-systems. It protects all the key machinery in the R&D Project called the Energy Recovery LINAC (ERL) against the high beam current. The MPS is capable of responding to a fault with an interlock signal within several microseconds. The ERL MPS is based on a National Instruments CompactRIO platform, and is programmed by utilizing National Instruments' development environment for a visual programming language. The system also transfers data (interlock status, time of fault, etc.) to the main server. Transferred data is integrated into the pre-existing software architecture which is accessible by the operators. This paper will provide an overview of the hardware used, its configuration and operation, as well as the software written both on the device and the server side.

A Reliability and Safety Program plan outline has been prepared for the operational phase of a Waste Isolation Facility. The program includes major functions of risk assessment, technical support activities, quality assurance, operational safety, configuration monitoring, reliability analysis and support and coordination meetings. Detailed activity or task descriptions are included for each function. Activities are time-phased and presented in the PERT format for scheduling and interactions. Task descriptions include manloading, travel, and computer time estimates to provide data for future costing. The program outlined here will be used to provide guidance from a reliability and safety standpoint to design, procurement, construction, and operation of repositories for nuclear waste. These repositories are to be constructed under the National Waste Terminal Storage program under the direction of the Office of Waste Isolation, Union Carbide Corp. Nuclear Division.

None

The Eppendorf-Biotronik Model IC 2001-2, a portable field ruggedized ion chromatography instrument, was rigorously tested at the DOE Advanced Waste Water Treatment Plant, Fernald, Ohio. This instrument rapidly detected the uranium concentration in water, and has a detection limit in the low ppb range without using the sample concentrating feature. The test set of samples analyzed included: ``Real World`` water samples from the AWWT containing uranium concentrations in the 9--110 ppb range, a sample blank, and a performance evaluation sample. The AWWT samples contained sets of both raw water and acid-preserved water samples. Selected samples were analyzed in quadruplicate to asses the instrument`s precision, and these results were compared with the results from an off-site confirmatory laboratory to assess the instrument`s accuracy. Additional comparisons with on-site laboratory instruments, Chemcheck KPA-11 and Scintrex UA-3 are reported. Overall, the Eppendorf-Biotronik IC 2001-2 performed exceptionally well providing a detection limit in the low ppb region (< 10 ppb) and giving rapid (< 5 minutes) accurate and reproducible analytical results for the AWWT, ``real world``, water samples with uranium concentrations in the region of interest (10--40 ppb). The per sample operating cost for this instrument is equivalent to the per sample cost for the …

An innovative feature of the proposed Energy Recovery Linac (ERL) is the use of a solenoid made with High Temperature Superconductor (HTS) with the Superconducting RF cavity. The use of HTS allows solenoid to be placed in close proximity to the cavity and thus provides early focusing of the electron beam. In addition, cryogenic testing at {approx}77 K is simpler and cheaper than 4 K testing. This paper will present the design, construction and test results of this HTS solenoid. The HTS solenoid in the proposed ERL will be situated in the transition region between the superconducting cavity at {approx}4 K and the cryostat at the room temperature. Solenoid inside the cryogenic structure provides an early focusing and hence low emittance beam. The temperature in the transition region will be too high for a conventional low temperature superconductor and resistive heat load from copper coils will be too high on cryogenic system. HTS coils also allow much higher current density and significant reduction in size as compared to copper coils. Hence HTS solenoid provide a unique and technically superior solution. The use of a HTS solenoid with superconducting cavity offers a unique option as it can be placed in a …

This document provides the final report on the research project of chemical milling of counterbore recesses in the uranium wall of Zircaloy-2 clad uranium tubes. The scope of work, results and conclusions, and experimental procedures are provided.

We report the results of a CP violation analysis of the decay B{sup {+-}} {yields} D{sub {pi}{sup +}{pi}{sup -}{pi}{sup 0}}K{sup {+-}}, where D{sub {pi}{sup +}{pi}{sup -}{pi}{sup 0}} indicates a neutral D meson detected in the final state {pi}{sup +}{pi}{sup -}{pi}{sup 0}, excluding K{sub S}{sup 0}{pi}{sup 0}. The analysis makes use of 324 million e{sup +}e{sup -} {yields} B{bar B} events recorded by the BABAR experiment at the PEP-II e{sup +}e{sup -} storage ring. By analyzing the {pi}{sup +}{pi}{sup -}{pi}{sup 0} Dalitz plot distribution and the B{sup {+-}} {yields} D{sub {pi}{sup +}{pi}{sup -}{pi}{sup 0}} K{sup {+-}} branching fraction and decay rate asymmetry, we calculate parameters related to the phase {gamma} of the CKM unitarity triangle. We also measure the magnitudes and phases of the components of the D{sup 0} {yields} {pi}{sup +}{pi}{sup -}{pi}{sup 0} decay amplitude.

A temperature dependent D2O density model has been developed for the 3-D hydraulics module in the near real-time plant analysis code ULTRASIM. By replacing the constant density, ULTRASIM is improved in two ways. First, all 3-D hydraulic analyses performed are more physically realistic now that the temperature dependence of the D2O density is accounted for. Secondly, simple temperature driven process water transients can now be modeled and investigated, including natural circulation tests. This report describes results in both of these areas.

This report describes the experimental procedure for Type 304 Stainless Steel fracture toughness measurements and the application of results. Typical toughness values are given based on the completed test program for the Reactor Materials Program (RMP). Test specimen size effects and limitations of the applicability in the fracture mechanics methodology are outlined as well as a brief discussion on irradiation effects.

A major concern for the implementation of crab crossing in a future High-Luminosity LHC (HL-LHC) is machine protection in an event of a fast crab-cavity failure. Certain types of abrupt crab-cavity amplitude and phase changes are simulated to characterize the effect of failures on the beam and the resulting particle-loss signatures. The time-dependent beam loss distributions around the ring and particle trajectories obtained from the simulations allow for a first assessment of the resulting beam impact on LHC collimators and on sensitive components around the ring. Results for the nominal LHC lattice is presented.

We argue that dark matter particles which have strong interactions with the Standard Model particles are not excluded by current astrophysical constraints. These dark matter particles have unique signatures at colliders; instead of missing energy, the dark matter particles produce jets. We propose a new search strategy for such strongly interacting particles by looking for a signal of two trackless jets. We show that suitable cuts can plausibly allow us to find these signals at the LHC even in early data.

The Brookhaven Booster Main Magnet Power Supply (MMPS) is a 24 pulse thyristor control supply, rated at 5500 Amps, +/-2000 Volts, or 3000 Amps, +/-6000 Volts. The power supply is fed directly from the power utility and the peak magnet power is 18 MWatts. This peak power is seen directly at the incoming ac line. This power supply has been in operation for the last 18 years. This paper will describe the present topology and operation of the power supply, the feedback control system and the different modes of operation of the power supply. Since the power supply has been in operation for the last 18 years, upgrading this power supply is essential. A new power supply topology has been studied where energy is stored in capacitor banks. DC to DC converters are used to convert the dc voltage stored in the capacitor banks to pulsed DC voltage into the magnet load. This enables the average incoming power from the ac line to be constant while the peak magnet power is pulsed to +/- 18 MWatts. Simulations and waveforms of this power supply will be presented.

In aerobic aquifers typical of many Department of Energy (DOE) legacy waste sites, uranium is present in the oxidized U(VI) form which is more soluble and thus more mobile. Field experiments at the Old Rifle UMTRA site have demonstrated that biostimulation by electron donor addition (acetate) promotes biological U(VI) reduction (2). However, U(VI) reduction is reversible and oxidative dissolution of precipitated U(IV) after the cessation of electron donor addition remains a critical issue for the application of biostimulation as a treatment technology. Despite the potential for oxidative dissolution, field experiments at the Old Rifle site have shown that rapid reoxidation of bio-reduced uranium does not occur and U(VI) concentrations can remain at approximately 20% of background levels for more than one year. The extent of post-amendment U(VI) removal and the maintenance of bioreduced uranium may result from many factors including U(VI) sorption to iron-containing mineral phases, generation of H2S or FeS0.9, or the preferential sorption of U(VI) by microbial cells or biopolymers, but the processes controlling the reduction and in situ reoxidation rates are not known. To investigate the role of microbial community composition in the maintenance of bioreduced uranium, in-well sediment incubators (ISIs) were developed allowing field deployment of …

We have investigated collective effects in an ultimate storage ring, i.e. one with diffraction limited emittances in both planes, using PEP-X as an example. In an ultimate ring intra-beam scattering (IBS) sets the limit of current that can be stored. In PEP-X, a 4.5 GeV ring running round beams at 200 mA in 3300 bunches, IBS doubles the emittances to 11.5 pm at the design current. The Touschek lifetime is 11 hours. Impedance driven collective effects tend not to be important since the beam current is relatively low. We have investigated collective effects in PEP-X, an ultimate storage ring, i.e. one with diffraction limited emittances (at one angstrom wavelength) in both planes. In an ultimate ring intra-beam scattering (IBS) sets the limit of current that can be stored. In PEP-X, IBS doubles the emittances to 11.5 pm at the design current of 200 mA, assuming round beams. The Touschek lifetime is quite large in PEP-X, 11.6 hours, and - near the operating point - increases with decreasing emittance. It is, however, a very sensitive function of momentum acceptance. In an ultimate ring like PEP-X impedance driven collective effects tend not to be important since the beam current is relatively low. …

The goals of this project are to develop a catalyst and process for the conversion of syngas to isobutanol. The research will identify and optimize key catalyst and process characteristics. In addition, the commercial potential of the new process will be evaluated by an economic analysis. The combination of the best conditions from independent process variable studies has afforded the best performance to date with the 2% Pt on Zn/Mn/Zr oxide catalyst. At 325{degrees}C, 300 psig, 7/1 MeOH/EtOH molar feed ratio and 1 hr{sup {minus}1} MEOH WH 22.20% selectivity to isobutanol is obtained with 55 and 97% conversions of methanol and ethanol, respectively. The results of this run will be used as a basis for the economic evaluation of a higher alcohols process. The ability of the Pt on Zn/Mn/Zr oxide catalyst to produce isobutanol in the presence of high partial pressures of H{sub 2} has been investigated. Such operation could allow the integration of a higher alcohol process with a conventional methanol synthesis plant by placing it within the methanol synthesis recycle loop. However, higher alcohol yields are severely suppressed by a large H{sub 2} cofeed, even at pressures as low as 50 psig. Elimination of the H{sub 2} …

We study single and coupled-bunch instabilities for the NSLS-II storage ring with a recently developed parallel tracking code. For accurate modelling of the coupled-bunch instability, we investigate improvements to current point-bunch models to take into account finite bunch-size effects. Accurate modelling of single and coupled-bunch instabilities is of crucial importance for the machine performance of light sources such as NSLS-II, that provide high current beams. The complexity of the model consists in the accurate calculation of the impedance of the various components of the ring that can excite single and multibunch instabilities via short and long range wakefields. Moreover, a full account of the coupling between transverse and longitudinal dynamics must be taken into account to study effects such as chromaticity and Landau cavity effects. A parallel algorithm for the study of single and coupled-bunch instabilities has been implemented in a particle tracking code. The theoretical framework for single bunch instabilities is the same used in the code TRANFT, while for coupled-bunch instabilities a self-consistent algorithm has been implemented to allow the study of finite bunch-size effects and multibunch effects in arbitrary filling modes. In this paper we present numerical studies of the microwave instability for NSLS-II and discuss the …

We compare our 2D mean field (Vlasov-Maxwell) treatment of coherent synchrotron radiation (CSR) effects with 1D approximations of the CSR force which are commonly implemented in CSR codes. In our model we track particles in 4D phase space and calculate 2D forces [1]. The major cost in our calculation is the computation of the 2D force. To speed up the computation and improve 1D models we also investigate approximations to our exact 2D force. As an application, we present numerical results for the Fermi{at}Elettra first bunch compressor with the configuration described in [1].