This report examines the problem of an antenna radiating from a cylindrical hole in the earth and the subsequent far-zone field produced in the upper air half space. The approach used for this analysis was to first examine propagation characteristics along the hole for surrounding geologic material properties. Three cases of sand with various levels of moisture content were considered as the surrounding material to the hole. For the hole diameters and sand cases examined, the radiation through the earth medium was found to be the dominant contribution to the radiation transmitted through to the upper half-space. In the analysis presented, the radiation from a vertical and a horizontal dipole source within the hole is used to determine a closed-form expression for the radiation in the earth medium which represents a modified element factor for the source and hole combination. As the final step, the well-known results for a dipole below a half space, in conjunction with the use of Snell's law to transform the modified element factor to the upper half space, determine closed-form expressions for the far-zone radiated fields in the air region above the earth.

Regardless of the form of restructuring, deregulatedelectricity industries share one common feature: the absence of anysignificant, rapid demand-side response to the wholesale (or, spotmarket) price. For a variety of reasons, most electricity consumers stillpay an average cost based regulated retail tariff held over from the eraof vertical integration, even as the retailers themselves are oftenforced to purchase electricity at volatile wholesale prices set in openmarkets. This results in considerable price risk for retailers, who aresometimes additionally forbidden by regulators from signing hedgingcontracts. More importantly, because end-users do not perceive real-time(or even hourly or daily) fluctuations in the wholesale price ofelectricity, they have no incentive to adjust their consumptionaccordingly. Consequently, demand for electricity is highly inelastic,which together with the non storability of electricity that requiresmarket clearing over very short time steps spawn many other problemsassociated with electricity markets, such as exercise of market power andprice volatility. Indeed, electricity generation resources can bestretched to the point where system adequacy is threatened. Economictheory suggests that even modest price responsiveness can relieve thestress on generation resources and decrease spot prices. To quantify thiseffect, actual generator bid data from the New York control area is usedto construct supply stacks and intersect them with demand curves …

The Performance Demonstration Program (PDP) for Nondestructive Assay (NDA) is a test program designed to yield data on measurement system capability to characterize drummed transuranic (TRU) waste generated throughout the Department of Energy (DOE) complex. The tests are conducted periodically and provide a mechanism for the independent and objective assessment of NDA system performance and capability relative to the radiological characterization objectives and criteria of the Office of Characterization and Transportation (OCT). The primary documents requiring an NDA PDP are the Waste Acceptance Criteria for the Waste Isolation Pilot Plant (WAC), which requires annual characterization facility participation in the PDP, and the Quality Assurance Program Document (QAPD). This NDA PDP implements the general requirements of the QAPD and applicable requirements of the WAC. Measurement facilities must demonstrate acceptable radiological characterization performance through measurement of test samples comprised of pre-specified PDP matrix drum/radioactive source configurations. Measurement facilities are required to analyze the NDA PDP drum samples using the same procedures approved and implemented for routine operational waste characterization activities. The test samples provide an independent means to assess NDA measurement system performance and compliance per criteria delineated in the NDA PDP Plan. General inter-comparison of NDA measurement system performance among DOE …

This cleanup verification package documents completion of remedial action for the 300-18 waste site. This site was identified as containing radiologically contaminated soil, metal shavings, nuts, bolts, and concrete.

With the continuing trend of decreasing feature sizes in flip-chip assemblies, the reliability tolerance to interfacial flaws is also decreasing. Small-scale disbonds will become more of a concern, pointing to the need for a better understanding of the initiation stage of interfacial delamination. With most accepted adhesion metric methodologies tailored to predict failure under the prior existence of a disbond, the study of the initiation phenomenon is open to development and standardization of new testing procedures. Traditional fracture mechanics approaches are not suitable, as the mathematics assume failure to originate at a disbond or crack tip. Disbond initiation is believed to first occur at free edges and corners, which act as high stress concentration sites and exhibit singular stresses similar to a crack tip, though less severe in intensity. As such, a 'fracture mechanics-like' approach may be employed which defines a material parameter--a critical stress intensity factor (K{sub c})--that can be used to predict when initiation of a disbond at an interface will occur. The factors affecting the adhesion of underfill/polyimide interfaces relevant to flip-chip assemblies were investigated in this study. The study consisted of two distinct parts: a comparison of the initiation and propagation phenomena and a comparison of …

Computer simulation has become increasingly important in many scientific disciplines, but its performance and scalability are severely limited by the memory throughput on today’s computer systems. With the support of this grant, we first designed training-based prediction, which accurately predicts the memory performance of large applications before their execution. Then we developed optimization techniques using dynamic computation fusion and large-scale data transformation. The research work has three major components. The first is modeling and prediction of cache behav- ior. We have developed a new technique, which uses reuse distance information from training inputs then extracts a parameterized model of the program’s cache miss rates for any input size and for any size of fully associative cache. Using the model we have built a web-based tool using three dimensional visualization. The new model can help to build cost-effective computer systems, design better benchmark suites, and improve task scheduling on heterogeneous systems. The second component is global computation for improving cache performance. We have developed an algorithm for dynamic data partitioning using sampling theory and probability distribution. Recent work from a number of groups show that manual or semi-manual computation fusion has significant benefits in physical, mechanical, and biological simulations as well …

Results from Super-K, SNO, and KamLAND provide strong evidence that neutrinos undergo flavor-changing oscillations and therefore have non-zero mass. The {nu}-disappearance observations by KamLAND, assuming CPT conservation, point to matter enhanced (MSW) oscillations with large mixing angles as the solution to the solar neutrino problem--a result consistent with the MSW parameters recently defined by these experiments. This requires that the observed neutrino flavors (e, {mu}, and tau) are not mass eigenstates, but are linear combinations of the mass eigenstates of the neutrino. However, such oscillation experiments can only determine the differences in the masses of the neutrinos, not the absolute scale of neutrino mass. What can be inferred from these experiments is that at least one species of neutrino has a mass greater than 55 meV. In fact, the WMAP observations of large-scale structure point to a sum-neutrino mass of {approx} 0.7 eV (roughly 0.25 eV/species assuming democracy between the flavors). Furthermore, there is still the important issue of whether the neutrino and anti-neutrino are distinct particles (i.e. Dirac type) or not (Majorana type). The only way to answer both of these questions is through neutrinoless double beta decay (DBD) experiments. CUORE (Cryogenic Underground Observatory for Rare Events) is a …

In gas chromatography, a chemical sample separates into its constituent components as it travels along a long thin column. As the component chemicals exit the column they are detected and identified, allowing the chemical makeup of the sample to be determined. For correct identification of the component chemicals, the distribution of the concentration of each chemical along the length of the column must be nearly symmetric. The prediction and control of asymmetries in gas chromatography has been an active research area since the advent of the technique. In this paper, we develop from first principles a general model for isothermal linear chromatography. We use this model to develop closed-form expressions for terms related to the first, second, and third moments of the distribution of the concentration, which determines the velocity, diffusion rate, and asymmetry of the distribution. We show that for all practical experimental situations, only fronting peaks are predicted by this model, suggesting that a nonlinear chromatography model is required to predict tailing peaks. For situations where asymmetries arise, we analyze the rate at which the concentration distribution returns to a normal distribution. Numerical examples are also provided.

Shock initiation experiments on the heated PBX9501 explosive (95% HMX, 2.5% estane, and 2.5% nitro-plasticizer by weight) were performed at temperatures 150 C and 180 C to obtain in-situ pressure gauge data. A 101 mm diameter propellant driven gas gun was utilized to initiate the PBX9501 explosive and manganin piezo-resistive pressure gauge packages were placed between sample slices to measure time resolved local pressure histories. The run-distance-to-detonation points on the Pop-plot for these experiments showed the sensitivity of the heated material to shock loading. This work shows that heated PBX-9501 is more shock sensitive than it is at ambient conditions. Proper Ignition and Growth modeling parameters were obtained to fit the experimental data. This parameter set will allow accurate code predictions to be calculated for safety scenarios involving PBX9501 explosives at temperatures close to those at which experiments were performed.

Deposition of maximum laser energy into a small, high-Z enclosure in a short laser pulse creates a hot environment. Such targets were recently included in an experimental campaign using the first four of the 192 beams of the National Ignition Facility [J. A. Paisner, E. M. Campbell, and W. J. Hogan, Fusion Technology 26, 755 (1994)], under construction at the University of California Lawrence Livermore National Laboratory. These targets demonstrate good laser coupling, reaching a radiation temperature of 340 eV. In addition, the Raman backscatter spectrum contains features consistent with Brillouin backscatter of Raman forward scatter [A. B. Langdon and D. E. Hinkel, Physical Review Letters 89, 015003 (2002)]. Also, NIF Early Light diagnostics indicate that 20% of the direct backscatter from these reduced-scale targets is in the polarization orthogonal to that of the incident light.

A simplified mechanical model is used to simulate the deformation of a scoria cone due to pressurization of magma in a feeder conduit. The scoria cone is modeled as consisting of a cone of stabilized scoria with an axial region of loose scoria (height h{sub 1}), all overlying a vertically oriented cylindrical conduit intruded into rhyolite tuff country rock. For our analyses, the conduit is filled with basalt magma, usually with the upper length (h{sub 2}) solidified. The style of deformation of the cone depends on both h{sub 1} and h{sub 2}. If magma is prevented from hydrofracturing out of the conduit (as, for example, might be the case if the magma is surrounded by a solidified, but plastically deformable layer acting as a gasket backed up by the brittle country rock) pressures in the magma can build to 10s of MPa. When h{sub 1} is 100 m, not unusual for a small isolated basaltic cinder cone, the magma pressure needed to destabilize the cone when molten magma extends all the way to the original ground surface (h{sub 2} = 0) is only about one-third of the pressure when the upper part of the conduit is solidified (h{sub 2} = …

U.S. Nuclear Regulatory Commission Interim Staff Guidance 8 (ISG-8) for burnup credit covers actinides only, a position based primarily on the lack of definitive critical experiments and adequate radiochemical assay data that can be used to quantify the uncertainty associated with fission product credit. The accuracy of fission product neutron cross sections is paramount to the accuracy of criticality analyses that credit fission products in two respects: (1) the microscopic cross sections determine the reactivity worth of the fission products in spent fuel and (2) the cross sections determine the reaction rates during irradiation and thus influence the accuracy of predicted final concentrations of the fission products in the spent fuel. This report evaluates and quantifies the importance of the fission product cross sections in predicting concentrations of fission products proposed for use in burnup credit. The study includes an assessment of the major fission products in burnup credit and their production precursors. Finally, the cross-section importances, or sensitivities, are combined with the importance of each major fission product to the system eigenvalue (k{sub eff}) to determine the net importance of cross sections to k{sub eff}. The importances established the following fission products, listed in descending order of priority, that …

A probabilistic analysis was conducted to estimate ranges for the numbers of waste packages that could be damaged in a potential future igneous event through a repository at Yucca Mountain. The analyses include disruption from an intrusive igneous event and from an extrusive volcanic event. This analysis supports the evaluation of the potential consequences of future igneous activity as part of the total system performance assessment for the license application for the Yucca Mountain Project (YMP). The first scenario, igneous intrusion, investigated the case where one or more igneous dikes intersect the repository. A swarm of dikes was characterized by distributions of length, width, azimuth, and number of dikes and the spacings between them. Through the use in part of a latin hypercube simulator and a modified video game engine, mathematical relationships were built between those parameters and the number of waste packages hit. Corresponding cumulative distribution function curves (CDFs) for the number of waste packages hit under several different scenarios were calculated. Variations in dike thickness ranges, as well as in repository magma bulkhead positions were examined through sensitivity studies. It was assumed that all waste packages in an emplacement drift would be impacted if that drift were intersected …

Incorporation of adaptive mesh refinement (AMR) into Lagrangian hydrodynamics algorithms allows for the creation of a highly powerful simulation tool effective for complex target designs with three-dimensional structure. We are developing an advanced modeling tool that includes AMR and traditional arbitrary Lagrangian-Eulerian (ALE) techniques. Our goal is the accurate prediction of vaporization, disintegration and fragmentation in National Ignition Facility (NIF) experimental target elements. Although our focus is on minimizing the generation of shrapnel in target designs and protecting the optics, the general techniques are applicable to modern advanced targets that include three-dimensional effects such as those associated with capsule fill tubes. Several essential computations in ordinary radiation hydrodynamics need to be redesigned in order to allow for AMR to work well with ALE, including algorithms associated with radiation transport. Additionally, for our goal of predicting fragmentation, we include elastic/plastic flow into our computations. We discuss the integration of these effects into a new ALE-AMR simulation code. Applications of this newly developed modeling tool as well as traditional ALE simulations in two and three dimensions are applied to NIF early-light target designs.

Eruptive conduit geometry has direct relation to number of waste packages that would be damaged if a new volcano were to form at the proposed Yucca Mountain radioactive waste repository, and therefore is a key factor in predicting the consequences of such an eruption. Current risk calculations treat conduits as having circular plan view and range from a few meters to 150 m diameter at repository depths ({approx}300 m). We present new observations of shallow basaltic plumbing at analog sites aimed at testing these parameter values. East Grants Ridge. NM, is a remnant of a {approx}2.6 Ma alkali basaltic volcano with a chain of 2-3 vents that fed {approx}10-km long lava flows. The south side of the ridge exposes a plug of vertically jointed, dense basalt that intruded rhyolitic tuffs. The plug is exposed vertically for {approx}125 m, including 40 m beneath the paleosurface, and has a relatively constant width of {approx}135 m with no indication of downward narrowing. The size of the plug in the third dimension is not well known but could extend laterally up to {approx}1.5 km beneath the chain of vents. Paiute Ridge, NV, is an 8.6 Ma alkali basalt intrusion into Paleozoic carbonate and shale …

We report the two-dimensional alignment of semiconductor islands using rudimentary metal patterning to control nucleation and growth. In the Ge on Si system, a square array of sub-micron Au dots on the Si (001) surface induces the assembly of deposited Ge adatoms into an extensive island lattice. Remarkably, these highly ordered Ge islands form between the patterned Au dots and are characterized by a unique truncated pyramidal shape. A model based on patterned diffusion barriers explains the observed ordering and establishes general criteria for the broader applicability of such a directed assembly process to quantum dot ordering.

The primary purpose of the project was to identify materials and methods that will make the envelope of a house flood damage resistant. Flood damage resistant materials and systems are intended to be used to repair houses subsequent to flooding. This project was also intended to develop methods of restoring the envelopes of houses that have been flooded but are repairable and may be subject to future flooding. Then if the house floods again, damage will not be as extensive as in previous flood events and restoration costs and efforts will be minimized. The purpose of the first pair of field tests was to establish a baseline for typical current residential construction practice. The first test modules used materials and systems that were commonly found in residential envelopes throughout the U.S. The purpose of the second pair of field tests was to begin evaluating potential residential envelope materials and systems that were projected to be more flood-damage resistant and restorable than the conventional materials and systems tested in the first pair of tests. The purpose of testing the third slab-on-grade module was to attempt to dry flood proof the module (no floodwater within the structure). If the module could be …

None

Formation of desert pavement and accretionary soils are intimately linked in arid environments such as the Mojave Desert. Well-sorted fallout scoria lapilli at Lathrop Wells (75-80 ky) and Red Cone ({approx}1 Ma) volcanoes (southern Nevada) formed an excellent starting material for pavement, allowing infiltration of eolian silt and fine sand that first clogs the pore space of underlying tephra and then aggrades and develops vesicular A (Av) horizons. Variations in original pyroclast sizes provide insight into minimum and maximum clast sizes that promote pavement and soil formation: pavement becomes ineffective when clasts can saltate under the strongest winds, while clasts larger than coarse lapilli are unable to form an interlocking pavement that promotes silt accumulation (necessary for Av development). Contrary to predictions that all pavements above altitudes of {approx}400 m would have been ''reset'' in their development after late Pleistocene vegetation advances (about 15 ka), the soils and pavements show clear differences in maturity between the two volcanoes. This indicates that either the pavements/soils develop slowly over many 10,000's of years and then are very stable, or that, if they are disrupted by vegetation advances, subsequent pavements are reestablished with successively more mature characteristics.

We imaged-highly attenuating test objects in three dimensions with 9-MV (at LLNL) and 15-MV (at Hill Air Force Base) x-ray spectra. While we used the same detector and motion control, there were differences that we could not control in the two radiography bays and in the sources. The results show better spatial resolution for the 9-MV spectrum and better contrast for the 15-MV spectrum. The 15-MV data contains a noise pattern that obfuscates the data. It is our judgment that if sufficient attention were given to design of the bay, beam dump, collimation, filtration and linac spot size; a 15-MV imaging system using a flat panel could be developed with spatial resolution of 5 lp/mm and contrastive performance better than we have demonstrated using a 9-MV spectrum.

We calculate the leading order BFKL amplitude for the exclusive diffractive process {gamma}*{sub L}(Q{sub 1}{sup 2}) {gamma}*{sub L}(Q{sub 2}{sup 2}) {yields} {rho}{sub L}{sup 0}{rho}{sub L}{sup 0} in the forward direction, which can be studied in future high energy e{sup +}e{sup -} linear colliders. The resummation effects are very large compared to the fixed-order calculation. We also estimate the next-to-leading logarithmic corrections to the amplitude by using a specific resummation of higher order effects and find a substantial growth with energy, but smaller than in the leading logarithmic approximation.

None

The purpose of this project is to formulate a ''Supercement'' designed for improving the long-term sealing integrity in HPHT wells. Phase I concentrated on chemistry studies and screening tests to design and evaluate Portland-based, hybrid Portland, and non-Portland-based cement systems suitable for further scale-up testing. Phase II work concentrated on additional lab and field testing to reduce the candidate materials list to two systems, as well as scale up activities aimed at verifying performance at the field scale. Phase II was extended thorough a proposal to develop additional testing capabilities aimed at quantifying cementing material properties and performance that were previously not possible. Two materials are being taken into Phase III for field testing and commercialization: {lg_bullet} Highly-expansive cement (Portland-based), patent pending as ''Pre-Stressed Cement'' {lg_bullet} Epoxy Resin (non-Portland-based), patent pending In Phase II, significant effort was expended on scaling up the processes for handling resin in the field, as it is quite different than conventional Portland-based cements in mixing, personnel protection, and cleanup. Through this effort, over fifty (50) field jobs were done at a variety of temperatures and depths, most with excellent results. Large-scale field testing was less relevant with Pre-stressed Cement, because the materials and surface processes …

Pacific Northwest National Laboratory (PNNL: Operated by Battelle Memorial Institute for the Department of Energy) is working with the Department of Energy (DOE) to develop technology for the US mining industry. PNNL was awarded a three-year program to develop automated on-board/in-line or on-site oil analysis for the mining industry.