BNL plans to create a very long base line super neutrino beam facility by upgrading the AGS from the current 0.14 MW to 1.0 MW and beyond. The proposed facility consists of three major components. First is a 1.5 GeV superconducting linac to replace the booster as injector for the AGS, second is the performance upgrade of the AGS itself for higher intensity and repetition rate, and finally is the target and horn system for the neutrino production. The major contribution for the higher power is from the increase of the repetition rate of the AGS from 0.3 Hz to 2.5 Hz, with moderate increase from the intensity. The accelerator design considerations to achieve high intensity and low losses for the new linac and the AGS will be presented. The target and horn design for high power operation and easy maintenance will also be covered.

This paper treats an exact elastica solution for a clamped-hinged beam, and its application to a carbon nanotube. Although the elastica has a long history, and the exact post-buckling solution for the Euler buckling problem has been known for at least 150 years, it seems that the elastica solution obtained in this paper constitutes an addition to the existing family of elastica solutions. As an application of the results, a post-buckling analysis of a single wall carbon nanotube is studied. Also, a potential use of the posting-buckling analysis of the carbon nanotube for the determination of its Young's modulus has been indicated.

We review recent research that assesses evidence for the detection of anthropogenic and natural external influences on the climate. Externally driven climate change has been detected by a number of investigators in independent data covering many parts of the climate system, including surface temperature on global and large regional scales, ocean-heat content, atmospheric circulation, and variables of the free atmosphere, such as atmospheric temperature and tropopause height. The influence of external forcing is also clearly discernible in reconstructions of hemispheric scale temperature of the last millennium. These observed climate changes are very unlikely to be due only to natural internal climate variability, and they are consistent with the responses to anthropogenic and natural external forcing of the climate system that are simulated with climate models. The evidence indicates that natural drivers such as solar variability and volcanic activity are at most partially responsible for the large-scale temperature changes observed over the past century, and that a large fraction of the warming over the last 50 years can be attributed to greenhouse gas increases. Thus the recent research supports and strengthens the IPCC Third Assessment Report conclusion that ''most of the global warming over the past 50 years is likely due …

Understanding the phase stability of Alloy 22 (N06022) is important since the precipitation of tetrahedrally close-packed (TCP) phases over time has been known to adversely affect corrosion and mechanical properties. Prior observations have shown that these phases precipitate during the welding process. After welding, residual stresses due to the solidification and cooling from temperature remain. When the weld cannot be stress-relieved by solution annealing, the application of commercially available stress-mitigation processes such as low plasticity burnishing (LPB) and laser shock peening (LSP) may be used to produce near-surface compressive stresses. This study involved examination of cross-sectional samples of aged 1.25 inch thick welds of Alloy 22 plates using electron backscatter diffraction (EBSD) for TCP identification and micrograph analysis for TCP quantification. Precipitation in both the as-welded and LSP weld was observed primarily in inter-dendritic regions whilst precipitation in the LPB weld was in both inter- and intra-dendritic regions.

Experimental measurements of delayed fission-product gamma-ray transmission through low-enriched UO{sub 2} fuel pin lattices in an air medium were conducted at the Rensselaer Polytechnic Institute Reactor Critical Facility (RCF). The RCF core consists of excess Special Power Excursion Reactor Test (SPERT) fuel pins, enriched to 4.81 weight percent {sup 235}U, clad in stainless steel. An experimental apparatus was constructed to hold various arrangements of fuel pin lattices. The arrangements consisted of a single activated source pin taken from the reactor core surrounded by inactive fuel pins in an air medium. A sodium-iodide detector and gamma-ray spectroscopy system was used to generate a pulse-height spectrum of the gamma-ray radiation for detector positions outside the lattice. The change in radiation intensity as the detector is rotated about the vertical axis of the lattice, the ''channeling effect,'' was measured. Experimental measurements of the channeling effect were performed for six arrangements; 3 x 3, 5 x 5, and 7 x 7 lattices, with both the comer position and center position containing the activated pin. The results of the measurements demonstrate that the gamma-ray radiation intensity can vary widely, as a function of angle, relative to the vertical axis of the lattice.

A system for maintaining a sample at a constant temperature below 10K after deactivating the cooling source is demonstrated. In this system, the cooling source is a GM cryocooler that is joined with the sample through an adaptor that consists of a helium pot and a resistive medium. Upon deactivating the cryocooler, the power applied to a heater located on the sample side of the resistive medium is decreased gradually to maintain an appropriate temperature rise across the resistive medium as the helium pot warms. The temperature is held constant in this manner without the use of solid or liquid cryogens and without mechanically disconnecting the sample from the cooler. Shutting off the cryocooler significantly reduces sample motion that results from vibration and expansion/contraction of the cold head housing. The reduction in motion permits certain processes that are very sensitive to sample position stability, but are not performed throughout the duration that the sample is at low-temperature. An apparatus was constructed to demonstrate this technique using a 4K GM cryocooler. Experimental and theoretical predictions indicate that when the helium pot is pressurized to the working pressure of the cryocooler's helium supply, a sample with continuous heat dissipation of several-hundred milliwatts …

Phase stability and aging mechanisms in a water-quenched (WQ) U-6wt% Nb (U-14at% Nb) alloy artificially aged at 200 C and naturally aged at ambient temperature for 15 years have been investigated and studied using Vickers-hardness measurement, X-ray diffraction (XRD) analysis, and transmission electron microscopy (TEM) techniques. Age hardening/softening phenomenon is recorded from the artificially aged samples based upon the microhardness measurement. The age hardening can be readily rationalized by the occurrence of fine-scaled Nb segregation, or spinodal decomposition, within the {alpha}'' domains, which results in the formation of a modulated structure containing nano-scaled Nb-rich and Nb-lean domains. Prolonged aging leads to age softening of the alloy by coarsening of the modulated structure. Chemical ordering, or disorder-order phase transformation, is found within the naturally aged alloy according to TEM observations of antiphase domain boundaries (APBs) and superlattice diffraction patterns. A possible superlattice structure for the ordered {alpha}'' phase observed in the naturally aged sample and underlying low-temperature aging mechanisms are proposed.

In this paper the authors describe the approach to research, develop, and evaluate prototype middleware tools and architectures. The developed tools can be used by scientists to compose astronomical data analysis pipelines easily. They use the SuperMacho data pipelines as example applications to test the framework. they describe their experience from scheduling and running these analysis pipelines on massive parallel processing machines. they use MCR a Linux cluster machine with 1152 nodes and Luster parallel file system as the hardware test-bed to test and enhance the scalability of the tools.

Thermophotovoltaic (TPV) diodes fabricated from InGaAsSb alloys lattice-matched to GaSb substrates are grown by Metal Organic Vapor Phase Epitaxy (MOVPE). 0.53eV InGaAsSb TPV diodes utilizing front-surface spectral control filters have been tested in a vacuum cavity and a TPV thermal-to-electric conversion efficiency ({eta}{sub TPV}) and a power density (PD) of {eta}{sub TPV} = 19% and PD=0.58 W/cm{sup 2} were measured for T{sub radiator} = 950 C and T{sub diode} = 27 C. Recombination coefficients deduced from minority carrier measurements and the theory reviewed in this article predict a practical limit to the maximum achievable conversion efficiency and power density for 0.53eV InGaAsSb TPV. The limits for the above operating temperatures are projected to be {eta}{sub TPV} = 26% and PD = 0.75 W/cm{sup 2}. These limits are extended to {eta}{sub TPV} = 30% and PD = 0.85W/cm{sup 2} if the diode active region is bounded by a reflective back surface to enable photon recycling and a two-pass optical path length. The internal quantum efficiency of the InGaAsSb TPV diode is close to the theoretically predicted limits, with the exception of short wavelength absorption in GaSb contact layers. Experiments show that the open circuit voltage of the 0.53eV InGaAsSb TPV diodes …

Previous modeling for HIF drivers concentrated on designs in which 100 or more beams are grouped in an array and accelerated through a common set of induction cores. The total beam energy required by the target is achieved by the combination of final ion energy, current per beam and number of beams. Economic scaling favors a large number of small ({approx}1 cm dia.) beams. An alternative architecture has now been investigated, which we refer to as a modular driver. In this case, the driver is subdivided into many (>10) independent accelerators with one or many beams each. A key objective of the modular driver approach is to be able to demonstrate all aspects of the driver (source-to-target) by building a single, lower cost module compared to a full-scale, multi-beam driver. We consider and compare several design options for the modular driver including single-beam designs with solenoid instead of quadrupole magnets in order to transport the required current per module in a single beam, solenoid/quad combinations, and multi-beam, all-quad designs. The drivers are designed to meet the requirements of the hybrid target, which can accommodate a larger spot size than the distributed radiator target that was used for the Robust Point …

Residential single family building practice currently ignores the losses of energy and water caused by the poor design of hot water systems. These losses include; the waste of water while waiting for hot water to get to the point of use; the wasted heat as water cools down in the distribution system after a draw; and the energy needed to reheat water that was already heated once before. Average losses of water are estimated to be 6.35 gallons (24.0 L) per day. (This is water that is rundown the drain without being used while waiting for hot water.) The amount of wasted hot water has been calculated to be 10.9 gallons (41.3L) per day. (This is water that was heated, but either is not used or issued after it has cooled off.) A check on the reasonableness of this estimate is made by showing that total residential hot water use averages about 52.6 gallons (199 L) per day. This indicates about 20 percent of average daily hot water is wasted.

The intermediate valence compounds Yb{sub 2}M{sub 3}Ga{sub 9} (M = Rh, Ir) exhibit an anisotropic magnetic susceptibility. We report measurements of the temperature dependence of the 4f occupation number, n{sub f}(T), for Yb{sub 2}M{sub 3}Ga{sub 9} as well as the magnetic inelastic neutron scattering spectrum S{sub mag}({Delta}E) at 12 and 300 K for Yb{sub 2}Rh{sub 3}Ga{sub 9}. Both n{sub f}(T) and S{sub mag}({Delta}E) were calculated for the Anderson impurity model with crystal field terms within an approach based on the non-crossing approximation. These results corroborate the importance of crystal field effects in these materials; they also suggest that Anderson lattice effects are important to the physics of Yb{sub 2}M{sub 3}Ga{sub 9}.

We present a novel method for computing cache-oblivious layouts of large meshes that improve the performance of interactive visualization and geometric processing algorithms. Given that the mesh is accessed in a reasonably coherent manner, we assume no particular data access patterns or cache parameters of the memory hierarchy involved in the computation. Furthermore, our formulation extends directly to computing layouts of multi-resolution and bounding volume hierarchies of large meshes. We develop a simple and practical cache-oblivious metric for estimating cache misses. Computing a coherent mesh layout is reduced to a combinatorial optimization problem. We designed and implemented an out-of-core multilevel minimization algorithm and tested its performance on unstructured meshes composed of tens to hundreds of millions of triangles. Our layouts can significantly reduce the number of cache misses. We have observed 2-20 times speedups in view-dependent rendering, collision detection, and isocontour extraction without any modification of the algorithms or runtime applications.

Atmospheric testing of nuclear weapons during the 1950s and early 1960s doubled the level of radiocarbon ({sup 14}C) in the atmosphere. From the peak in 1963, the level of {sup 14}CO{sub 2} has decreased exponentially with a mean life of about 16 years, not due to radioactive decay, but due to mixing with large marine and terrestrial carbon reservoirs. Since radiocarbon is incorporated into all living things, the bomb-pulse is an isotopic chronometer of the past half century. The absence of bomb radiocarbon in skeletonized human remains generally indicates a date of death before 1950. Comparison of the radiocarbon values with the post 1950 bomb-curve may also help elucidate when in the post 1950 era, the individual was still alive. Such interpretation however, must consider the age at death of the individual and the type of tissue sampled.

DElight is a simulation engine for daylight and electric lighting system analysis in buildings. DElight calculates interior illuminance levels from daylight, and the subsequent contribution required from electric lighting to meet a desired interior illuminance. DElight has been specifically designed to integrate with building thermal simulation tools. This paper updates the DElight capability set, the status of integration into the simulation tool EnergyPlus, and describes a sample analysis of a simple model from the user perspective.

The objective of this paper is to introduce the process and philosophies used to implement the new Work Smart Standard (WSS), ''Safety Basis Requirements for Nonnuclear Facilities at Lawrence Livermore National Laboratory Site Specific Standard'' (UCRL-ID-150214), approved in 2003 and revised January, 2004. This work relates directly to the following workshop theme: ''Improvements in Chemical, Biological, and Non-nuclear Safety Analysis.'' This paper will describe the approach used to implement the new nonnuclear standard at LLNL and corresponding guidance manual: ES&H Manual, Document 3.1. The varied activities can be broken down into three main parts: (1) Implementation Plan Schedule. The Implementation Plan includes the due dates for revising nonnuclear facility safety analysis documentation to meet the new standard. Implementation of the new methodology is being phased over a 4-year period. Each directorate was tasked to schedule the revision date for each of their nonnuclear facilities, using agreed upon priority-ranking criteria. (2) Program Infrastructure. This includes the development of training courses, procedures, a website and tools required to perform the work (i.e. Q List, de minimus list) or tools helpful to perform the work; such as a program to automate the classification of chemical inventories and establish maximum facility inventory limits (MFILs). …

Article discussing an M-like potassium current in the guinea pig cochlea.

A moderate (M{approx}5) earthquake struck the northeastern United Arab Emirates (UAE) and northern Oman on March 11, 2002. The event was felt over a wide area of the northern Emirates and was accompanied by smaller (felt) events before and after the March 11 main shock. The event was large enough to be detected and located by global networks at teleseismic distances. We estimated focal mechanism and depth from broadband complete regional waveform modeling. We report a normal mechanism with a slight right-lateral strike-slip component consistent with the large-scale tectonics. The normal component suggests relaxation of obducted crust of the Semail Ophilite (specifically, the Khor Fakkan Block) while the right-lateral strike-slip component of the mechanism is consistent with shear across the Oman Line. Felt earthquakes are rare in the region, however no regional seismic network exists in the UAE to determine local seismicity. This event offers a unique opportunity to study the active tectonics of the region as well as inform future studies of seismic hazard in the UAE and northern Oman.

None

A diagnostic was developed for the determination of temporal history of an X-ray spot. A pair of thin (0.5 mm) slits image the x-ray spot to a fast scintillator which is coupled to a fast detector, thus sampling a slice of the X-Ray spot. Two other scintillator/detectors are used to determine the position of the spot and total forward dose. The slit signal is normalized to the dose and the resulting signal is analyzed to get the spot size. The position information is used to compensate for small changes due to spot motion and misalignment. The time resolution of the diagnostic is about 1 ns and measures spots from 0.5 mm to over 3 mm. The theory and equations used to calculate spot size and position are presented, as well as data. The calculations assume a symmetric, Gaussian spot. The spot data is generated by the ETA II accelerator, a 2kA, 5.5 MeV, 60 ns electron beam focused on a Tantalum target. The spot generated is typically about 1 mm FWHM. Comparisons are made to an X-ray pinhole camera which images the X-Ray spot (in 2D) at four time slices.

The force fields used in molecular computational biology are not mathematically defined in such a way that their mathematical representation would facilitate the straightforward application of volume visualization techniques. To visualize energy, it is necessary to define a spatial mapping for these fields. Equipped with such a mapping, we can generate volume renderings of the internal energy states in a molecule. We describe our force field, the spatial mapping that we used for energy, and the visualizations that we produced from this mapping. We provide images and animations that offer insight into the computational behavior of the energy optimization algorithms that we employ.

We report combined x-ray and Raman studies of beryllium in helium or argon pressure medium at pressures approaching 200 GPa. Our results are generally consistent with recent studies confirming the stability of the hexagonal close-packed phase to the highest pressures. However, the quasi-hydrostatic conditions of our studies lead to a stiffer equation of state (K{sub 0} = 109.88, K'{sub 0} = 3.59) and a gradual approach toward a more ideal c/a ratio of 1.60 at 180 GPa. Combining our Raman and EOS data, we are able to evaluate the pressure dependence of the elastic shear modulus (C{sub 44} = 109.3, C'{sub 44} = 1.959). We discuss the comparison of our results with measurements using ultrasonic and dynamic techniques.

Previous X-ray Diffraction (XRD) and Nuclear Magnetic Resonance (NMR) studies on Ti-doped NaAlH{sub 4} revealed the reaction products of two heavily doped (33.3 at.%) samples that were solvent-mixed and mechanically-milled. This investigation revealed that nano-crystalline or amorphous Al{sub 2}O{sub 3} forms from the possible coordination of aluminum with oxygen atom of the furan ring system from added tetrahydrofuran (THF) in the solvent-mixed sample, and that TiAl{sub 3} forms in mechanically-milled samples. The present paper provides a more sophisticated NMR investigation of the these materials. On heavily doped (33.3 at.%) solvent-mixed samples, {sup 27}Al Magic Angle Spinning (MAS) NMR {sup 27}Al multiple quantum MAS (MQMAS) indicates the presence of an oxide layer of Al{sub 2}O{sub 3} on the surfaces of potentially bulk nanocrystalline Ti, nanocrystalline TiAl{sub 3}, and/or metallic aluminum. The {sup 1}H MAS NMR data also indicate the possible coordination of aluminum with the oxygen atom in the THF. On heavily doped samples that were mechanically milled, {sup 27}Al MAS NMR and static NMR confirms the presence of TiAl{sub 3}. In addition, the {sup 1}H MAS NMR and {sup 1}H spin-lattice relaxation (T{sub 1}) measurements are consistent with the presence of TiH{sub 2}. These results are in agreement with recent …

Most single-crystal shock experiments have been performed in high-symmetry directions while the nature of shock propagation in low-symmetry directions remains relatively unstudied. It is well known that small-amplitude, linear acoustic waves propagating in low-symmetry directions can focus and/or form caustics (Wolfe, 1995). In this report we provide evidence for similar focusing behavior in nonlinear (shock) waves propagating in single crystals of silicon and diamond. Using intense lasers, we have driven non-planar (divergent geometry) shock waves through single-crystals of silicon or diamond and into an isotropic backing plate. On recovery of the backing plates we observe a depression showing evidence of anisotropic plastic strain with well-defined crystallographic registration. We observe 4-, 2-, and 3-fold symmetric impressions for [100], [110], and [111] oriented crystals respectively.