The contribution of lubrication oil to particulate matter (PM) emissions from a Cummins B5.9 Diesel engine was measured using accelerator mass spectrometry to trace carbon isotope concentrations. The engine operated at fixed medium load (285 N-m (210 ft.lbs.) 1600 m) used 100% biodiesel fuel (B100) with a contemporary carbon-14 ({sup 14}C) concentration of 103 amol {sup 14}C/ mg C. The C concentration of the exhaust C02 and PM were 102 and 99 amol {sup 14}C/mg C, respectively. The decrease in I4C content in the PM is due to the consumption of lubrication oil which is {sup 14}C-free. Approximately 4% of the carbon in PM came from lubrication oil under these operating conditions. The slight depression in CO{sub 2} isotope content could be attributed to ambient CO{sub 2} levels and measurement uncertainty.

Several recent works have considered variants of the mortar-finite element method for numerical treatment of contact phenomena. The method has shown considerable promise for the spatial discretization of contact interactions, particularly for kinematically linear applications where one or both of the contacting surfaces are flat. Desirable features already demonstrated for the method in this specialized setting include passage of patch tests, preservation of convergence rates that would be obtained with a perfectly conforming mesh, and accurate resolution of contact stresses on interfaces. This paper concerns itself with the successful extension of these methods to encompass contact of geometrically noncoincident surfaces. The issue of patch test passage over curved interfaces will be discussed. It will be shown that a generalization of the mortar projection method is required to pass patch tests in this instance. Issues relating to the exact numerical integration of the mortar projection integrals will also be outlined, and a convergence study for a mortar tying application will be presented.

The National Ignition Facility (NIF), currently under construction at the University of California's Lawrence Livermore National Laboratory is a $2.25B stadium-sized facility containing a 192-beam, 1.8-Megajoule, 500-Terawatt, 351-nm laser system. NIF is being built by the National Nuclear Security Agency and when completed will be the world's largest laser system, providing a national center to study inertial confinement fusion and the physics of extreme energy densities and pressures. In NIF up to 192 energetic laser beams will compress small fusion targets to conditions where they will ignite and burn, liberating more energy than is required to initiate the fusion reactions. NIF experiments will allow the study of physical processes at temperatures approaching 100 million K and 100 billion times atmospheric pressure. These conditions exist naturally only in the interior of stars and in nuclear weapons explosions. In the course of designing the world's most energetic laser system, a number of significant technology breakthroughs have been achieved. Research is also underway to develop a shorter pulse capability on NIF for high power applications. We discuss here the technology challenges and solutions that have made NIF possible along with enhancements to NIF's design that could lead to exawatt power levels.

This paper discusses the Non-Equilibrium Zeldovich - von Neumann - Doring (NEZND) theory of self-sustaining detonation waves and the Ignition and Growth reactive flow model of shock initiation and detonation wave propagation in solid explosives. The NEZND theory identified the non-equilibrium excitation processes that precede and follow the exothermic decomposition of a large high explosive molecule into several small reaction product molecules. The thermal energy deposited by the leading shock wave must be distributed to the vibrational modes of the explosive molecule before chemical reactions can occur. The induction time for the onset of the initial endothermic reactions can be calculated using high pressure, high temperature transition state theory. Since the chemical energy is released well behind the leading shock front of a detonation wave, a physical mechanism is required for this chemical energy to reinforce the leading shock front and maintain its overall constant velocity. This mechanism is the amplification of pressure wavelets in the reaction zone by the process of de-excitation of the initially highly vibrationally excited reaction product molecules. This process leads to the development of the three-dimensional structure of detonation waves observed for all explosives. For practical predictions of shock initiation and detonation in hydrodynamic codes, …

A fundamental problem in providing high-quality surveillance images recorded over long horizontal or slant paths is the blurring caused by atmospheric turbulence, which reduces both the resolution and contrast. The objective of the work reported here is to develop a capability for long-range imaging through the atmosphere that is not limited by the atmosphere but only by the fundamental diffraction limit of the optics. This paper describes our recent horizontal and slant-path imaging experiments of point targets and extended scenes as well as simulations of point targets in comparison to experiment. We show the near-diffraction limited resolution results obtained using bispectral speckle-imaging techniques. The experiments were performed with an 8-inch diameter telescope placed either in a field, on a rooftop, or on a hillside and cover ranges of interest from 100 meters up to 10 km. The scenery includes resolution targets, people, vehicles, and other structures.

Transparent conducting oxides (TCOs) are a group of materials that are widely used in solar cells and other optoelectronic devices. Recently, Cu-containing p-type TCOs such as MII Cu2 O2 (MIII=Mg, Ca, Sr, Ba) and CuMIII O2 (MIII=Al, Ga, In) have been proposed. Using first-principles band structure methods, we have systematically studied the electronic and optical properties of these p-type transparent oxides. For MII Cu2 O2 , we predict that adding a small amount of Ca into Sr Cu2 O2 can increase the transparency and conductivity. For CuMIII O2 , we explained the doping and band gap anomalies in this system and proposed a new approach to search for bipolar dopable wide-gap materials.

An 11.4% partial Siberian snake was used to successfully accelerate polarized proton through a strong intrinsic depolarizing spin resonance in the AGS. No noticeable depolarization was observed. This opens up the possibility of using a 20% to 30% partial Siberian snake in the AGS to overcome all weak and strong depolarizing spin resonances. Some design and operation issues of the new partial Siberian snake are discussed.

Tomographic images of tissue phantoms and a sample of breast tissue have been produced from an acoustic synthetic array system for frequencies near 500 kHz. The images for sound speed and attenuation show millimeter resolution and demonstrate the feasibility of obtaining high-resolution tomographic images with frequencies that can deeply penetrate tissue. The image reconstruction method is based on the Born approximation to acoustic scattering and is a simplified version of a method previously used by Andre (Andre, et. al., Int. J. Imaging Systems and Technology, Vol 8, No. 1, 1997) for a circular acoustic array system. The images have comparable resolution to conventional ultrasound images at much higher frequencies (3-5 MHz) but with lower speckle noise. This shows the potential of low frequency, deeply penetrating, ultrasound for high-resolution quantitative imaging.

A new method that combines staggered grid Arbitrary Lagrangian-Eulerian (ALE) techniques with structured local adaptive mesh refinement (AMR) has been developed for solution of the Euler equations. The novel components of the combined ALE-AMR method hinge upon the integration of traditional AMR techniques with both staggered grid Lagrangian operators as well as elliptic relaxation operators on moving, deforming mesh hierarchies. Numerical examples demonstrate the utility of the method in performing detailed three-dimensional shock-driven instability calculations.

Localization of targets imbedded in a heterogeneous background medium is a common problem in seismic, ultrasonic, and electromagnetic imaging problems. The best imaging techniques make direct use of the eigenfunctions and eigenvalues of the array response matrix, as recent work on time-reversal acoustics has shown. Of the various imaging functionals studied, one that is representative of a preferred class is a time-domain generalization of MUSIC (MUltiple Signal Classification), which is a well-known linear subspace method normally applied only in the frequency domain. Since statistical stability is not characteristic of the frequency domain, a transform back to the time domain after first diagonalizing the array data in the frequency domain takes optimum advantage of both the time-domain stability and the frequency-domain orthogonality of the relevant eigenfunctions.

Multiresolution methods provide a means for representing data at multiple levels of detail. They are typically based on a hierarchical data organization scheme and update rules needed for data value computation. We use a data organization that is based on what we call n{radical}2 subdivision. The main advantage of subdivision, compared to quadtree (n = 2) or octree (n = 3) organizations, is that the number of vertices is only doubled in each subdivision step instead of multiplied by a factor of four or eight, respectively. To update data values we use n-variate B-spline wavelets, which yields better approximations for each level of detail. We develop a lifting scheme for n = 2 and n = 3 based on the n{radical}2-subdivision scheme. We obtain narrow masks that could also provide a basis for view-dependent visualization and adaptive refinement.

This conference paper describes Microcrystalline silicon films were grown with different thicknesses and different hydrogen dilution ratios on glass and Si substrates. Some films were deposited with a seed layer, whereas others were deposited directly on the substrate. We used atomic force microscopy, scanning electron microscopy, and X-ray diffraction to study the morphology and crystalline structure of the samples. We did not find a significant influence of the different substrates on the morphology or crystalline structure. The presence of the seed layer enhanced the crystallization process, decreasing the amount of amorphous layer present in the films. The microstructure of most films was formed by grains, with a subgrain structure. Films grown with low values of dilution ratio had (220) texture and elongated grains, whereas films deposited with high values of dilution ratio were randomly oriented and had an irregular shape.

Recent advances in field and laboratory methods for measuring elastic wave velocities provide incentive and opportunity for improving interpretation of geophysical data for engineering and environmental applications. Advancing the state-of-the-art of seismic imaging requires developing petrophysical relationships between measured velocities and the hydrogeology parameters and lithology. Our approach uses laboratory data and rock physics methods. Compressional (Vp) and shear (Vs) wave velocities, Vp/Vs ratios, and relative wave amplitudes show systematic changes related to composition, saturation, applied stress (analogous to depth), and distribution of clay for laboratory ultrasonic measurements on soils. The artificial soils were mixtures of Ottawa sand and a second phase, either Wyoming bentonite or peat moss used to represent clay or organic components found in natural soils. Compressional and shear wave velocities were measured for dry, saturated, and partially-saturated conditions, for applied stresses between about 7 and 100 kPa, representing approximately the top 5 m of the subsurface. Analysis of the results using rock physics methods shows the link between microstructure and wave propagation, and implications for future advances in seismic data interpretation. For example, we found that Vp in dry sand-clay mixtures initially increases as clay cements the sand grains and fills porosity, but then Vp decreases …

The MLS grid free rezone method, a simple, flexible finite difference method to solve general mechanics problems, especially detonation problems, is proposed in this paper. The spatial points that carry time dependent data are distributed in space in such a way that provides nearly uniform spacing of points, accurate presentation of boundaries, easy variation of resolutions and arbitrary deletion of irrelevant regions. Local finite difference operators are obtained with simple MLS differentiation. There is no specific topological or geometrical restriction with the distribution of data points. Therefore this method avoids many drawbacks of the traditional CFD methods. Because of its flexibility, it can be used to simulate a wide range of mechanics problems. Because of its simplicity, it has the potential to become a preferred method. Most traditional CFD methods, from a SPH view, can be considered as special cases of grid free methods of specific kernel functions. Such a generalization allows the development of a unified grid free CFD code that can be switched to various CFD methods by switching the kernel functions. Because of the flexibility in management and simplicity of coding, such a unified code is desired.

This conference paper describes the measurement of the photovoltaic (PV) performance with respect to reference conditions requires measuring the performance with respect to a reference spectrum. Procedures were developed in the mid 1980s to correct measurements for errors relating to the spectral irradiance of the light source being different from the standard and the responsivity of the irradiance detector being different from the device under test. In principle, these procedures are exact, but require the measurement of the spectral irradiance of the light source and responsivity of the test device. This is problematic for most facilities that measure module performance. It has been suggested that a polynomial fit of the short-circuit current (I sc ) measured under natural sunlight divided by the total broadband irradiance as a function of air mass provides an accurate spectral correction factor. The polynomial correction factor is normalized to unity at an absolute air mass of 1.5.The polynomial correction factor is compared with the spectral correction factor for a variety of devices at two locations.

A four-chamber piston pump is powered by decomposed 85% hydrogen peroxide. The performance envelope of the evolving 400 gram pump has been expanded to 172 cc/s water flow at discharge pressures near 5 MPa. A gas generator cycle system using the pump has been tested under similar conditions of pressure and flow. The powerhead gas is derived from a small fraction of the pumped hydrogen peroxide, and the system starts from tank pressures as low as 0.2 MPa. The effects of steam condensation on performance have been evaluated.

Metallic films are grown with a sponge-like morphology in the as-deposited condition using planar magnetron sputtering. The morphology of the deposit is characterized by metallic continuity in three dimensions with continuous porosity on the sub-micron scale. The stabilization of the metallic sponge is directly correlated with a limited range for the sputter deposition parameters of working gas pressure and substrate temperature. This sponge-like morphology augments the features as generally understood in the classic zone models of growth for physical vapor deposits. Nickel coatings are deposited with working gas pressures up to 4 Pa and for substrate temperatures up to 1100 K. The morphology of the deposits is examined in plan and in cross-section with scanning electron microscopy. The parametric range of gas pressure and substrate temperature (relative to absolute melt point) for the deposition processing under which the metallic sponges are produced appear universal for many metals, as for example, including gold, silver, and aluminum.

Measuring the violence of a thermal explosion of a cased explosive is important for evaluating safety issues of explosive devices in fires. A sympathetic initiation scenario was studied here where a 9.0 cm diameter by 2.5 cm thick disc of PBX 9501 donor charge encased in a 304 stainless steel assembly was heated on top and bottom flat surfaces until it thermally exploded. The initial heating rate at the metal/explosive interface was 5 C per minute until it reaches 170 C; then this temperature is held for 35 minutes to allow temperature equilibration to within a few degrees throughout the explosive. The heating resumed at a rate of 1 C per minute until the PBX 9501 donor thermally exploded. A PBX 9501 acceptor charge with carbon resistor and manganin foil pressure gauges inserted at various depths was placed at a 10 cm standoff distance from the donor charge's top steel cover plate. Piezoelectric arrival time pins were placed in front of the acceptor surface to measure the velocity and shape of the impacting plate. The stainless steel cover plate of the donor charge had a nominal velocity of 0.55 {+-} 0.04 mm/{micro}s upon impact and was non-symmetrically warped. The impact …

Atmospheric aberrations reduce the resolution and contrast in surveillance images recorded over horizontal or slant paths. This paper describes our recent horizontal and slant path imaging experiments of extended scenes as well as the results obtained using speckle imaging. The experiments were performed with an 8-inch diameter telescope placed on either a rooftop or hillside and cover ranges of interest from 0.5 km up to 10 km. The scenery includes resolution targets, people, vehicles, and other structures. The improvement in image quality using speckle imaging is dramatic in many cases, and depends significantly upon the atmospheric conditions. We quantify resolution improvement through modulation transfer function measurement comparisons.

A swift ion creates a track of electronic excitations in the target material. A net repulsion inside the track can cause a ''Coulomb Explosion'', which can lead to damage and sputtering of the material. Here we report results from molecular-dynamics (MD) simulations of Coulomb explosion for a cylindrical track as a function of charge density and neutralization/quenching time, {tau}. Screening by the free electrons is accounted for using a screened Coulomb potential for the interaction among charges. The yield exhibits a prompt component from the track core and a component, which dominates at higher excitation density, from the heated region produced. For the cases studied, the number of atoms ejected per incident ion, i.e. the sputtering yield Y, is quadratic with charge density along the track as suggested by simple models. Y({tau} = 0.2 Debye periods) is nearly 20% of the yield when there is no neutralization ({tau} {yields} {infinity}). The connections between ''Coulomb explosions'', thermal spikes and measurements of electronic sputtering are discussed.

Recent advances in solid-state modulators now permit the design of a new class of high current accelerators. These new accelerators will be able to operate in burst mode at frequencies of several MHz with unprecedented flexibility and precision in pulse format. These new modulators can drive accelerators to high average powers that far exceed those of any other technology and can be used to enable precision beam manipulations. New insulator technology combined with novel pulse forming lines and switching may enable the construction of a new type of high gradient, high current accelerator. Recent developments in these areas will be reviewed.

Insulated pressure vessels are cryogenic-capable pressure vessels that can be fueled with liquid hydrogen or ambient-temperature compressed hydrogen. This flexibility results in multiple advantages with respect to compressed hydrogen tanks or low-pressure liquid hydrogen tanks. Our work is directed at verifying that commercially available aluminum-lined, fiber-wrapped pressure vessels can be safely used to store liquid hydrogen. A series of tests have been conducted, and the results indicate that no significant vessel damage has resulted from cryogenic operation. Future activities include a demonstration project in which the insulated pressure vessels will be installed and tested on two vehicles. A draft standard will also be generated for certification of insulated pressure vessels.

The objective of the ''Local Integration of the National Atmospheric Release Advisory Center with Cities'' (LINC) program is to demonstrate the capability for providing local government agencies with an advanced operational atmospheric plume prediction capability, which can be seamlessly integrated with appropriate federal agency support for homeland security applications. LINC is a Domestic Demonstration and Application Program (DDAP) funded by the Chemical and Biological National Security Program (CBNP), which is part of the Department of Energy's (DOE) National Nuclear Security Administration (NNSA). LINC will make use of capabilities that have been developed the CBNP, and integrated into the National Atmospheric Release Advisory Center (NARAC) at Lawrence Livermore National Laboratory (LLNL). NARAC tools services will be provided to pilot study cities and counties to map plumes from terrorism threats. Support to these local agencies will include training and customized support for exercises, special events, and general emergencies. NARAC provides tools and services that map the probable spread of hazardous material which have been accidentally or intentionally released into the atmosphere. Primarily supported by the DOE, NARAC is a national support and resource center for planning, real-time assessment and detailed studies of incidents involving a wide variety of hazards, including radiological, chemical, …

The main objective of this study is to perform nonlinear dynamic earthquake time history analyses on Morrow Point Dam, which is located 263 km southwest of Denver, Colorado. This project poses many significant technical challenges, one of which is to model the entire Morrow Point Dam/Foundation Rock/Reservoir system which includes accurate geology topography. In addition, the computational model must be initialized to represent the existing dead loads on the structure and the stress field caused by the dead loads. To achieve the correct dead load stress field due to gravity and hydrostatic load, the computer model must account for the manner in which the dams were constructed. Construction of a dam finite element model with the correct as-built geometry of the dam structure and simply ''turning on'' gravity in the computer model will generally lead to an incorrect initial stress field in the structure. The sequence of segmented lifts typical of dam construction has a significant impact on the static stress fields induced in the dam. In addition, the dam model must also account for the interaction between the adjacent dam segments across the dam contraction joints. As a result of these challenges, it was determined that a significant amount …