None

This work studies multiscale phenomena in silicon micro-resonators which comprise the mechanical components of next-generation Micro-Electro-Mechanical Systems (MEMS). Unlike their larger relatives, the behavior of these sub-micron MEMS is not described well by conventional continuum models and finite elements, but it is determined appreciably by the interplay between physics at the Angstrom, nanometer and micron scales. As device sizes are reduced below the micron scale, atomistic processes cause systematic deviations from the behavior predicted by conventional continuum elastic theory. [1] These processes cause anomalous surface effects in the resonator frequency and quality factor--even for single crystal devices with clean surfaces due to thermal fluctuations. They also lead to unconventional failure mechanisms. The simulation of these atomistic effects is a challenging problem due to the large number of atoms involved and due to the fact that they are finite temperature phenomena. Our simulations include up to two million atoms in the device itself, and hundreds of millions more are in the proximal regions of the substrate. A direct, atomistic simulation of the motion of this many atoms is prohibitive, and it would be inefficient. The micronscale processes in the substrate are well-described by finite elements, and an atomistic simulation is not …

None

None

A technique is developed to construct bulk hydroxyapatite (HAp) with different cellular structures. The technique involves the initial synthesis of nanocrystalline hydroxyapatite powder from an aqueous solution using water-soluble compounds and then followed by spray drying into agglomerated granules. The granules were further cold pressed and sintered into bulks at elevated temperatures. The sintering behavior of the HAp granules was characterized and compared with those previously reported. Resulting from the fact that the starting HAp powders were extremely fine, a relatively low activation energy for sintering was obtained. In the present study, both porous and dense structures were produced by varying powder morphology and sintering parameters. Porous structures consisting of open cells were constructed. Sintered structures were characterized using scanning electron microscopy and x-ray tomography. In the present paper, hydroxyapatite coatings produced by magnetron sputtering on silicon and titanium substrates will also be presented. The mechanical properties of the coatings were measured using nanoindentation techniques and microstructures examined using transmission electron microscopy.

We developed the Scaled Thermal Explosion Experiment (STEX) to provide a database of reaction violence from thermal explosion of explosives of interest. A cylinder of explosive, 1, 2 or 4 inches in diameter, is confined in a steel cylinder with heavy end caps, and heated under controlled conditions until it explodes. Reaction violence is quantified by micropower radar measurement of the cylinder wall velocity, and by strain gauge data at reaction onset. Here we describe the test concept and design, show that the conditions are well understood, and present initial data with HMX-based explosives. The HMX results show that an explosive with high binder content yields less-violent reactions that an explosive with low binder content, and that the HMX phase at the time of explosion plays a key role in reaction violence.

One of the key elements of the Stochastic Finite Element Method, namely the polynomial chaos expansion, has been utilized in a nonlinear shock and vibration application. As a result, the computed response was expressed as a random process, which is an approximation to the true solution process, and can be thought of as a generalization to solutions given as statistics only. This approximation to the response process was then used to derive an analytically-based design specification for component shock response that guarantees a balanced level of marginal reliability. Hence, this analytically-based reference SRS might lead to an improvement over the somewhat ad hoc test-based reference in the sense that it will not exhibit regions of conservativeness. nor lead to overtesting of the design.

None

The goal of this joint LLNL-CalEnergy project is to develop a method for precipitating marketable silica from spent Salton Sea Geothermal Field (SSGF) brines. Many markets for silica exist. We have initially targeted production of silica as a rubber additive. Silica reinforced rubber gives tires less rolling resistance, greater tear strength, and better adhesion to steel belts. Previous silica precipitates produced by CalEnergy from Salton Sea brines were not suitable as rubber additives. They did not to disperse well in the rubber precursors and produced inferior rubber. CalEnergy currently minimizes silica scaling in some of their production facilities by acidifying the brine pH. The rate of silica precipitation slows down as the pH is lowered, so that energy extraction and brine reinfection are possible without unacceptable amounts of scaling even with more than 700 ppm SiO{sub 2} in solution. We are adding a step in which a small amount of base is added to the acidified brine to precipitate silica before reinfection. By carefully controlling the type, rate, and amount of base addition, we can optimize the properties of the precipitate to approach those of an ideal rubber additive.

None

None

None

None

An all solid-state kicker pulser for a high current induction accelerator (the Dual-Axis Radiographic Hydrodynamic Test facility DARHT-2) has been designed and fabricated. This kicker pulser uses multiple solid state modulators stacked in an inductive-adder configuration. Each modulator is comprised of multiple metal-oxide-semiconductor field-effect transistors (MOSFETs) which quickly switch the energy storage capacitors across a magnetic induction core. Metglas is used as the core material to minimize loss. Voltage from each modulator is inductively added by a voltage summing stalk and delivered to a 50 ohm output cable. A lumped element circuit model of the inductive adder has been developed to optimize the performance of the pulser. Results for several stalk geometries will be compared with experimental data.

None

None

None

None

None

A residential building in Tucson, Arizona, was studied to evaluate opportunities for reducing cooling energy use in a hot dry climate. The reduction of solar heat gain was strongly influenced by spectrally selective windows, architectural shading, and site shading from adjacent buildings. The study emphasized accurately modeling these features to account for effects on the energy load. Building performance was modeled using a detailed hourly energy simulation tool and was measured while unoccupied for a period of 12 days. Model inputs included direct measurements of the net air exchange rate, surface reflectance, and window transmittance. Model results showed good agreement with the direct measurements of cooling loads and air-conditioning energy use. A parametric study of annual energy use is presented showing the impacts of glazing type, architectural shading, site shading, and building orientation. It is important to understand these interactions to optimize energy savings in community-scale housing developments.

None

High pressure xenon ionization chamber detectors are possible alternatives to traditional thallium doped sodium iodide (NaI(Tl)) and hyperpure germanium as gamma spectrometers in certain applications. Xenon detectors incorporating a Frisch grid exhibit energy resolutions comparable to cadmium/zinc/telluride (CZT) (e.g. 2% {at} 662keV) but with far greater sensitive volumes. The Frisch grid reduces the position dependence of the anode pulse risetimes, but it also increases the detector vibration sensitivity, anode capacitance, voltage requirements and mechanical complexity. We have been investigating the possibility of eliminating the grid electrode in high-pressure xenon detectors and preserving the high energy resolution using electronic risetime compensation methods. A two-electrode cylindrical high pressure xenon gamma detector coupled to time-to-amplitude conversion electronics was used to characterize the pulse rise time of deposited gamma photons. Time discrimination was used to characterize the pulse rise time versus photo peak position and resolution. These data were collected to investigate the effect of pulse rise time compensation on resolution and efficiency.

None

Brookhaven National Laboratory is a US Department of Energy (DOE) multi-program research facility, located in Suffolk County in Long Island, New York. In 1997, groundwater monitoring revealed significant levels of tritium contamination from a reactor fuel pool. The public reaction was immediate and intense. In an unprecedented move, DOE terminated the contractor and rebid the Laboratory management contract. Brookhaven Science Associates (BSA), a partnership between Battelle and the State University of New York at Stony Brook, won the contract. BSA faced enormous challenges in the environmental area. One was changing the culture and mindset of staff and management with regard to environmental protection. Another was changing operations to fully integrate environmental stewardship into all facets of the Laboratory's missions. And finally, BSA needed to change the Laboratory's public image. This paper describes how BSA faced those challenges. DOE and BSA entered into a voluntary agreement with the US Environmental Protection Agency to conduct an in-depth evaluation of the environmental aspects and impacts of all activities onsite. A project was initiated to explore environmental problems associated with historical activities. BSA also has made significant investments in developing and implementing an Environmental Management System that is consistent with the ISO 14001 standard, …