The electrical conductivities of boron carbides, B{sub 12+x}C{sub 3{minus}x} with 0.1 < x < 1.7, between 300 and 1200K suggest the hopping of a nearly temperature-independent density of small (bi)polarons. The activation energies of the nobilities are low, {approx} 0.16 eV, and are nearly independent of the composition. At lower temperatures, conductivities have non-Arrhenius temperature dependencies and strong sensitivity to carbon concentration. Percolative aspects of low-temperature hopping are evident in this sensitivity to composition. Boron carbides' Seebeck coefficients are anomalous in that (1) they are much larger than expected from boron carbides' large carrier densities and (2) they depend only weakly on the carrier density. Carrier-induced softening of local vibrations gives contributions to the Seebeck coefficient that mirror the magnitudes and temperature dependencies found in boron carbides.

A technological break through for supporting rotating shafts is the active magnetic bearing (AMB). Active magnetic bearings offer some important advantages over conventional ball, roller or journal bearings such as reduced frictional drag, no physical contact in the bearing, no need for lubricants, compatibility with high vacuum and ultra-clean environments, and ability to control shaft position within the bearing. The disadvantages of the AMB system are the increased cost and complexity, reduced bearing stiffness and the need for a controller. Still, there are certain applications, such as high speed machining, biomedical devices, and gyroscopes, where the additional cost of an AMB system can be justified. The inherent actuator capabilities of the AMB offer the potential for active balancing of spindles and micro-shaping capabilities for machine tools, The work presented in this paper concentrates on an AMB test program that utilizes the actuator capability to dynamically balance a spindle. In this study, an unbalanced AMB spindle system was enhanced with an LMS (Least Mean Squares) algorithm combined with an existing PID (proportional, integral, differential) control. This enhanced controller significantly improved the concentricity of an intentionally unbalanced shaft. The study included dynamic system analysis, test validation, control design and simulation, as well …

We report the growth of InSb on GaAs using InAlSb buffers of high interest for magnetic field sensors. We have grown samples by metal-organic chemical vapor deposition consisting of {approximately} 0.55 {micro}m thick InSb layers with resistive InAlSb buffers on GaAs substrates with measured electron nobilities of {approximately}40,000 cm{sup 2}/V.s. We have investigated the In{sub 1{minus}x}Al{sub x}Sb buffers for compositions x{le}0.22 and have found that the best results are obtained near x=0.12 due to the tradeoff of buffer layer bandgap and lattice mismatch.

The purpose of this activity is to determine the structural performance of waste packages (WP) subject to rock fall design basis event (DBE) dynamic loads and document the calculation results that describe the threshold rock sizes for crack-initiation and through-cracks in waste package shells. This activity is associated with the waste package design. AP-3.12Q, Revision 0, ICN 0, Calculations, is used to develop the calculation.

The purpose of this calculation is to provide a bounding dose consequence analysis of the immobilized plutonium (can-in-canister) waste form to be handled at the Monitored Geologic Repository (MGR) at Yucca Mountain. The current concept for the Plutonium Can-in-Canister waste form is provided in Attachment III. A typical design basis event (DBE) defines a scenario that generally includes an initiating event and the sequences of events that follow. This analysis will provide (1) radiological releases and dose consequences for a postulated, bounding DBE and (2) design-related assumptions on which the calculated dose consequences are based. This analysis is part of the safety design basis for the repository. Results will be used in other analyses to determine or modify the safety classification and quality assurance level of repository structures, systems, and components (SSCs). The Quality Assurance (QA) program applies to this calculation. The work reported in this document is part of the analysis of MGR DBEs and is performed using AP-3.12Q, Calculations. The work done for this analysis was evaluated according to QAP-2-0, Control of Activities. This evaluation determined that such activities are subject to DOE/RW/0333PY Quality Assurance Requirements and Description (DOE 1998), requirements. This calculation is quality affecting because the …

New computer graphic developments at Oak Ridge National Ridge National Laboratory (ORNL) are being used to provide visualization of criticality safety models and calculational results as well as tools for criticality safety analysis input preparation. The purpose of this paper is to present the status of current development efforts to continue to enhance the SCALE (Standardized Computer Analyses for Licensing Evaluations) computer software system. Applications for criticality safety analysis in the areas of 3-D model visualization, input preparation and execution via a graphical user interface (GUI), and two-dimensional (2-D) plotting of results are discussed.

The authors calculate the transverse momentum distribution for the production of massive lepton-pairs in longitudinally polarized, proton-proton collider energies within the context of perturbative quantum chromodynamics. For values of the transverse momentum Q{sub {Tau}} greater than roughly half the pair mass Q, Q{sub {Tau}} > Q/2, they show that the differential cross section is dominated by subprocesses initiated by incident gluons, provided that the polarized gluon density is not too small. Massive lepton-pair differential cross sections should be a good source of independent constraints on the polarized gluon density, free from the experimental and theoretical complications of photon isolation that beset studies of prompt photon production. They provide predictions for the spin-averaged and spin-dependent differential cross sections as a function of Q{sub {Tau}} at energies relevant for the Relativistic Heavy Ion Collider (RHIC) at Brookhaven, and they compare these with predictions for real prompt photon production.

Interest in the sensitivity methods that were developed and widely used in the 1970s (the FORSS methodology at ORNL among others) has increased recently as a result of potential use in the area of criticality safety data validation procedures to define computational bias, uncertainties and area(s) of applicability. Functional forms of the resulting sensitivity coefficients can be used as formal parameters in the determination of applicability of benchmark experiments to their corresponding industrial application areas. In order for these techniques to be generally useful to the criticality safety practitioner, the procedures governing their use had to be updated and simplified. This paper will describe the resulting sensitivity analysis tools that have been generated for potential use by the criticality safety community.

This paper describes a functional slide rule that provides a readily usable �in-hand� method for estimating nuclear criticality accident information from sliding graphs, thereby permitting (1) the rapid estimation of pertinent criticality accident information without laborious or sophisticated calculations in a nuclear criticality emergency situation, (2) the appraisal of potential fission yields and external personnel radiation exposures for facility safety analyses, and (3) a technical basis for emergency preparedness and training programs at nonreactor nuclear facilities. The slide rule permits the estimation of neutron and gamma dose rates and integrated doses based upon estimated fission yields, distance from the fission source, and time-after criticality accidents for five different critical systems. Another sliding graph permits the estimation of critical solution fission yields based upon fissile material concentration, critical vessel geometry, and solution addition rate. Another graph provides neutron and gamma dose-reduction factors for water, steel, and concrete shields.

This paper presents the application of sensitivity and uncertainty (S/U) analysis methodologies to the data validation tasks of a criticality safety computational study. The S/U methods presented are designed to provide a formal means of establishing the area (or range) of applicability for criticality safety data validation studies. The development of parameters that are analogous to the standard trending parameters form the key to the technique. These parameters are the so-called D parameters, which represent the differences by energy group of S/U-generated sensitivity profiles, and c parameters, which are the k correlation coefficients, each of which give information relative to the similarity between pairs of selected systems. The use of a Generalized Linear Least-Squares Methodology (GLLSM) tool is also described in this paper. These methods and guidelines are also applied to a sample validation for uranium systems with enrichments greater than 5 wt %.

Calculations for long-term-disposal criticality safety of spent nuclear fuel requires the application of burnup credit because of the large mass of fissile material that will be present in the repository. Burnup credit calculations are based on depletion calculations that provide a conservative estimate of spent fuel contents, followed by criticality calculations to assess the value of keff for a spent fuel cask or a fuel configuration under a variety of probabilistically derived events. In order to ensure that the depletion calculation is conservative, it is necessary to both qualify and quantify assumptions that can be made in depletion models used to characterize spent fuel. Most effort in the United States this decade has focused on burnup issues related to pressurized-water reactors. However, requirements for the permanent disposal of fuel from boiling-water reactors has necessitated development of methods for prediction of spent fuel contents for such fuels. Concomitant with such analyses, validation is also necessary. This paper provides a summary of initial efforts at the Oak Ridge National Laboratory to better understand and validate spent fuel analyses for boiling-water-reactor fuel.

Hydroelectric power contributes about 10 percent of the electrical energy generated in the United States, and nearly 20 percent of the world�s electrical energy. It is a renewable energy source that can contribute significantly to reduction of greenhouse gases by offsetting conventional carbon-based electricity generation. However, rather than growing in importance, hydroelectric generation has actually declined in recent years, often as a consequence of environmental concerns centering around (1) restriction of upstream and downstream fish passage by the dam, and (2) alteration of water quality and river flows by the impoundment. The Advanced Hydropower Turbine System (AHTS) Program of the U.S. Department of Energy is developing turbine technology which would help to maximize global hydropower resources while minimizing adverse environmental effects. Major technical goals for the Program are (1) the reduction of mortality among turbine-passed fish to 2 percent or less, compared to current levels ranging up to 30 percent or greater; and (2) development of aerating turbines that would ensure that water discharged from reservoirs has a dissolved oxygen concentration of at least 6 mg/L. These advanced, �environmentally friendly� turbines would be suitable both for new hydropower installations and for retrofitting at existing dams. Several new turbine designs that …

Daily newspaper from Perry, Oklahoma that includes local, state, and national news along with advertising.

Daily newspaper from Chickasha, Oklahoma that includes local, state, and national news along with advertising.

Daily newspaper from Altus, Oklahoma that includes local, state, and national news along with advertising.

The ATLAS Electromagnetic (EM) calorimeter (EMCAL) Front End Board (FEB) will be located in custom-designed enclosures solidly connected to the feedtroughs. It is a complex mixed signal board which includes the preamplifier, shaper, switched capacitor array analog memory unit (SCA), analog to digital conversion, serialization of the data and related control logic. It will be described in detail elsewhere in these proceedings. The electromagnetic interference (either pick-up from the on board digital activity, from power supply ripple or from external sources) which affects coherently large groups of channels (coherent noise) is of particular concern in calorimetry and it has been studied in detail.

Daily newspaper from Baytown, Texas that includes local, state, and national news along with advertising.

One of the several activities the International Atomic Energy Agency (IAEA) inspectors perform in the verification process of Safeguard operations is the review and correlation of data from different sources. This process is often complex due to the different forms in which the data is presented. This paper describes some of the elements that are necessary to create a ''standardized'' structure for the verification of data. When properly collected and formatted, data can be analyzed with off-the shelf software applications using customized macros to automate the commands for the desired analysis. The standardized-data collection methodology is based on instrumentation guidelines as well as data structure elements, such as verifiable timing of data entry, automated data logging, identification codes, and others. The identification codes are used to associate data items with their sources and to correlate them with items from other data logging activities. The addition of predefined parameter ranges allows automated evaluation with the capability to provide a data summary, a cross-index of all data related to a specific event. Instances of actual databases are used as examples. The data collection guidelines described in this paper facilitate the use of data from a variety of instrumentation platforms and also allow …

A faculty flute recital performed at the UNT College of Music Recital Hall.

Implementation of quality maintenance programs is essential to enhancing sustainable continuous operations of United States funded Materials Protection, Control and Accountability (MPC and A) equipment/systems upgrades at various Russian nuclear facilities. An effective maintenance program is expected to provide assurances to both parties for achieving maximum continuous systems operations with minimum down time. To be effective, the program developed must focus on minimum down time for any part of a system. Minimum down time is realized through the implementation of a quality maintenance program that includes preventative maintenance, necessary diagnostic tools, properly trained technical staff, and an in-house inventory of required spare parts for repairing the impacted component of the system. A centralized maintenance management program is logistically essential for the success of this effort because of the large volume of MPC and A equipment/systems installed at those sites. This paper will discuss current programs and conditions at the Russian Research Center-Kurchatov Institute, the All-Russian Scientific Institute for Technical Physics and the All-Russian Research Institute of Experimental Physics and will address those steps necessary to implement an upgraded program at those sites.

None

The technology of microelectronics that has evolved over the past half century is one of great power and sophistication and can now be extended to many applications (MEMS and MOEMS) other than electronics. An interesting application of MEMS quantum devices is the detection of electromagnetic radiation. The operation principle of MEMS quantum devices is based on the photoinduced stress in semiconductors, and the photon detection results from the measurement of the photoinduced bending. These devices can be described as micromechanical photon detectors. In this work, we have developed a technique for simulating electronic stresses using finite element analysis. We have used our technique to model the response of micromechanical photon devices to external stimuli and compared these results with experimental data. Material properties, geometry, and bimaterial design play an important role in the performance of micromechanical photon detectors. We have modeled these effects using finite element analysis and included the effects of bimaterial thickness coating, effective length of the device, width, and thickness.

The multi-wavelength anomalous diffraction, or MAD, method of determining protein structure is becoming routine in protein crystallography. An increase in the number of tuneable synchrotrons beamlines coupled with the widespread availability position-sensitive X-ray detectors based on charged-coupled devices and having fast readout raised MAD structure determination to a new and exciting level. Ultra-fast MAD data collection is now possible. Recognition of the value of selenium for phasing protein structures and improvement of methods for incorporating selenium into proteins in the form of selenomethionine have attracted greater interest in the MAD method. Recent developments in crystallographic software are complimenting the above advances, paving the way for rapid protein structure determination. An overview of a typical MAD experiment is described here, with emphasis on the rates and quality of data acquisition now achievable at beamlines developed at third-generation synchrotrons sources.

In this paper we report on current activities related to the merger of differential/integral data (especially in the resolved-resonance region) with nuclear criticality safety computations. Techniques are outlined for closer coupling of many processes � measurement, data reduction, differential-data analysis, integral-data analysis, generating multigroup cross sections, data-testing, criticality computations � which in the past have been treated independently.