The Advanced Research Workshop (ARW) on Nuclear Materials Safety held June 8-10, 1998, in St. Petersburg, Russia, was attended by 27 Russian experts from 14 different Russian organizations, seven European experts from six different organizations, and 14 U.S. experts from seven different organizations. The ARW was conducted at the State Education Center (SEC), a former Minatom nuclear training center in St. Petersburg. Thirty-three technical presentations were made using simultaneous translations. These presentations are reprinted in this volume as a formal ARW Proceedings in the NATO Science Series. The representative technical papers contained here cover nuclear material safety topics on the storage and disposition of excess plutonium and high enriched uranium (HEU) fissile materials, including vitrification, mixed oxide (MOX) fuel fabrication, plutonium ceramics, reprocessing, geologic disposal, transportation, and Russian regulatory processes. This ARW completed discussions by experts of the nuclear materials safety topics that were not covered in the previous, companion ARW on Nuclear Materials Safety held in Amarillo, Texas, in March 1997. These two workshops, when viewed together as a set, have addressed most nuclear material aspects of the storage and disposition operations required for excess HEU and plutonium. As a result, specific experts in nuclear materials safety have been …

This paper explores the geometrical errors that reduce heliostat tracking accuracy at Solar Two. The basic heliostat control architecture is described. Then, the three dominant error sources are described and their effect on heliostat tracking is visually illustrated. The strategy currently used to minimize, but not truly correct, these error sources is also shown. Finally, a novel approach to minimizing error is presented.

In May of 1998, a technical basis and implementation guidelines document for A Technique for Human Event Analysis (ATHEANA) was issued as a draft report for public comment (NUREG-1624). In conjunction with the release of draft NUREG- 1624, a peer review of the new human reliability analysis method its documentation and the results of an initial test of the method was held over a two-day period in June 1998 in Seattle, Washington. Four internationally known and respected experts in HK4 or probabilistic risk assessment were selected to serve as the peer reviewers. In addition, approximately 20 other individuals with an interest in HRA and ATHEANA also attended the peer and were invited to provide comments. The peer review team was asked to comment on any aspect of the method or the report in which improvements could be made and to discuss its strengths and weaknesses. They were asked to focus on two major aspects: Are the basic premises of ATHEANA on solid ground and is the conceptual basis adequate? Is the ATHEANA implementation process adequate given the description of the intended users in the documentation? The four peer reviewers asked questions and provided oral comments during the peer review meeting …

Linearized methods are presented for appraising image resolution and parameter accuracy in images generated with two and three dimensional non-linear electromagnetic inversion schemes. When direct matrix inversion is employed, the model resolution and posterior model covariance matrices can be directly calculated. A method to examine how the horizontal and vertical resolution varies spatially within the electromagnetic property image is developed by examining the columns of the model resolution matrix. Plotting the square root of the diagonal of the model covariance matrix yields an estimate of how errors in the inversion process such as data noise and incorrect a priori assumptions about the imaged model map into parameter error. This type of image is shown to be useful in analyzing spatial variations in the image sensitivity to the data. A method is analyzed for statistically estimating the model covariance matrix when the conjugate gradient method is employed rather than a direct inversion technique (for example in 3D inversion). A method for calculating individual columns of the model resolution matrix using the conjugate gradient method is also developed. Examples of the image analysis techniques are provided on 2D and 3D synthetic cross well EM data sets, as well as a field data …

The so-called radiation-induced ductility (RID) reported in neutron-irradiated 47at%Al alloys is attributed to the formation of effective twin embryos in the presence of interstitial-type Frank loops in {gamma}-TiAl and the subsequent nucleation and growth of microtwins during post-irradiation tensile deformation. The stability of large faulted Frank loops is explained in terms of the repulsive interaction between Shockley and Frank partials. Interaction of only six ordinary slip dislocations with a Frank loop can facilitate a pole mechanism for twin formation to work. The relative ease of heterogeneous twin nucleation is the reason for the RID and the lack of changes in yield strength and work hardening.

Let me begin with some comments about transparency. We all have some perception or vision about the use of transparency for nuclear technology and nuclear non-proliferation. Although we probably have some common understanding of what it implies, there is no precise definition that is agreed upon. One of the most significant ideas in transparency is that it is considered to be a voluntary or unilateral action. The party, or organization, or nation that wants its activities to be transparent voluntarily provides information to other parties with the expectation of receiving some acceptance or good will in return. The organization giving the information determines what information to provide, how much, how often, and when. This is in contrast to official treaties and monitoring regimes, in which specific verification information and activities are prescribed. This should have the advantage for the transparent organization of being less intrusive and less costly than a treaty monitoring regime. Information related to sensitive nuclear technology, proprietary processes, and physical security is more easily protected. The difficultly for both parties, the transparent organization and the information recipients, is in determining what information is necessary for the desired confidence building. It must be recognized that this state of …

In industry, the need to maximize energy efficiency depends on the availability of suitable advanced materials. Ceramic composites are exemplary materials for many advanced engineering applications because they exhibit good thermal stability, oxidation resistance and enhanced toughness. Presently, ceramic composite fabrication processes are costly, often requiring high temperatures and pressures to achieve reasonable densities. Our research is focused on developing a processing technique, that will allow production of alumina/aluminum composites using relatively low temperatures and without the application of an external force, thus reducing the processing costs. Our composites were formed using Reactive Metal Penetration (RMP), which is a process involving the reaction of molten Al with a dense ceramic preform. The result is a near net shape ceramic/metal composite with interpenetrating phases. The volume fraction of metal in the composites was varied by doping an aluminosilicate ceramic preform with silica. For this study we fabricated composites using pure mullite and mullite doped with 23 and 42 weight percent silica, yielding 18, 25, and 30 volume percent metal in the composites, respectively. Optical and Scanning Electron Microscopy were used to characterize the homogeneity and scale of the microstructure. The scale of the microstructure varied with preform composition, the reaction temperature …

We have constructed a single ring to resonantly double an 18 watt Nd:YLF mode-locked laser and re-double the stored green to produce over 4 watts of power in the ultra-violet (UV). This laser is used to produce a beam of 470 MeV gamma-rays by Compton backscattering the laser beam from 2.8 GeV electrons stored in a synchrotron. Achieving high luminosity of the colliding beams requires very good mode quality and beam stability at the intersection point 22 meters from the laser. The ring consists of six mirrors, with two 25 cm radius of curvature mirrors enclosing each nonlinear crystal. The drive laser is a lamp pumped Nd:YLF with a 50 ps bunch length at 76 MHz. A pointing stabilizer servo has been constructed as part of the infrared (IR) mode matching telescope. The IR to green conversion is accomplished in a 15 mm long non-critically phased matched LB0 crystal located at a 40 micron waist, with an IR conversion efficiency of 70%. A stable, nearly diffraction limited W beam of up to 4.2 watts is generated in a BBO crystal in the green storage ring. The output power is relatively independent of the efficiency of the LB0 and BBO crystals. …

None

None

Interracial segregation and partitioning in a polysynthetically twinned Ti-48.4 at.% Al-0.6% Zr alloy were investigated by atom probe field ion microscopy and atom probe tomography. The compositions of the {gamma} and {alpha}{sub 2} phases were determined to be Ti-47.5% Al-O.71% Zr-0.06% O and Ti-31.6% Al-0.68% Zr-2.4% O, respectively. These results indicate a high concentration of zirconium in both matrix phases, confirming a strength increase through solid-solution strengthening, but no significant zirconium partitioning to either phase. Although zirconium additions produced a refined lamellar microstructure in this material, compositional analysis of {gamma}/{gamma} and {gamma}/{alpha}{sub 2} interfaces showed no evidence of significant zirconium segregation. This suggests that zirconium additions may produce a refined lamellar microstructure, but may not be effective at providing resistance to growth and coarsening.

Seep C was a free-flowing stream of groundwater that emerged in a narrow valley below the old low-level waste (LLW) disposal trenches in Solid Waste Storage Area 5 (SWSA 5) at Oak Ridge National Laboratory (ORNL). The flow rate of the seep water was strongly influenced by rainfall, and typically ranged from 0.5 to 8 L/min. The seep water entered Melton Branch, a small stream that joins White Oak Creek before exiting the ORNL boundary. The seep water contained high concentrations of {sup 90}Sr (10,000 to 20,000 Bq/L) and, before the full-scale treatment system was installed, contributed about 25% of all the {sup 90}Sr leaving ORNL. Seep C was identified as a primary source of off-site contaminant transport and was designated for an early removal action under the Comprehensive Environmental Response and Liability Act (CERCLA). A passive flow treatment system was chosen as the most cost-effective method for treating the water.

The adhesion of alumina scales to aluminide bond coats is a life-limiting factor for some advanced thermal barrier coating systems. This study investigated the effects of aluminide bond coat sulfur and platinum contents on alumina scale adhesion and coating microstructural evolution during isothermal and cyclic oxidation testing at 1150 C. Low-sulfur NiAl and NiPtAl bond coats were fabricated by chemical vapor deposition (CVD). Lowering the sulfur contents of CVD NiAl bond coatings significantly improved scale adhesion, but localized scale spallation eventually initiated along coating grain boundaries. Further improvements in scale adhesion were obtained with Pt additions. The observed influences of Pt additions included: (1) mitigation of the detrimental effects of high sulfur levels, (2) drastic reductions in void growth along the scale-metal interface, (3) alteration of the oxide-metal interface morphology, and (4) elimination of Ta-rich oxides in the Al{sub 2}O{sub 3} scales during thermal cycling. The results of this study also suggested that the microstructure (especially the grain size) of CVD aluminide bond coatings plays a significant role in scale adhesion.

Biomass fuels are considered to be a promising renewable source of energy. However, impurities present in the fuel may cause corrosion problems with the materials used in the hot sections of gas turbines and only limited data are available so far. As part of the Advanced Turbine Systems Program initiated by the U.S. Department of Energy, the present study provides initial data on the hot corrosion resistance of different nickel-base alloys against sodium sulfate-induced corrosion as a baseline, and against salt compositions simulating biomass-derived fuel deposits. Single crystal nickel-superalloy Rene N5, a cast NiCrAlY alloy, a NiCoCrAlY alloy representing industrially used overlay compositions, and a model {beta}NiAl+Hf alloy were tested in 1h thermal cycles at 950 C with different salt coatings deposited onto the surfaces. Whereas the NiCoCrAlY alloy exhibited reasonable resistance against pure sodium sulfate deposits, the NiCrAiY alloy and Rene N5 were attacked severely. Although considered to be an ideal alumina former in air and oxygen at higher temperatures, {beta}NiAl+Hf also suffered from rapid corrosion attack at 950 C when coated with sodium sulfate. The higher level of potassium present in biomass fuels compared with conventional fuels was addressed by testing a NiCoCrAlY alloy coated with salts of …

This paper describes a life cycle analysis system (LCAS) developed to support US Department of Energy (DOE) decision-making regarding deactivation and decommissioning (D and D), pollution prevention (P2), and asset recovery, and its deployment to analyze the disposition of facilities and capital assets. Originally developed for use at the Oak Ridge East Tennessee Technology Park, this approach has been refined through application at Ohio Operations Office sites and is now being deployed at a number of DOE sites. Programs such as National Metals Recycle, the D and D Focus Area, P2, and Asset Utilization are successfully using the system to make better decisions resulting in lower cost to the taxpayer and improved environmental quality. The LCAS consists of a user-friendly, cost-effective, and analytically-sound decision-aiding process and a complementary suite of automated tools to handle data administration and multiple criteria life cycle analysis (LCA). LCA is a systematic and comprehensive process for identifying, assessing, and comparing alternatives for D and D, P2, and asset recovery at government sites, and for selecting and documenting a preferred alternative. An LCA includes all of the impacts (benefits and costs) that result from a course of action over the entire period of time affected by …

The life cycle analysis toolbox is a valuable integration of decision-making tools and supporting materials developed by Oak Ridge National Laboratory (ORNL) to help Department of Energy managers improve environmental quality, reduce costs, and minimize risk. The toolbox provides decision-makers access to a wide variety of proven tools for pollution prevention (P2) and waste minimization (WMin), as well as ORNL expertise to select from this toolbox exactly the right tool to solve any given P2/WMin problem. The central element of the toolbox is a multiple criteria approach to life cycle analysis developed specifically to aid P2/WMin decision-making. ORNL has developed numerous tools that support this life cycle analysis approach. Tools are available to help model P2/WMin processes, estimate human health risks, estimate costs, and represent and manipulate uncertainties. Tools are available to help document P2/WMin decision-making and implement programs. Tools are also available to help track potential future environmental regulations that could impact P2/WMin programs and current regulations that must be followed. An Internet-site will provide broad access to the tools.

Measurements of liquid permeability in the mushy zones of AI-15.42% Cu and Al-8.68% Cu alloy samples have been performed isothermally just above the eutectic temperature, using eutectic liquid as the fluid. A modified method has been developed to determine the specific permeability, K{sub s}, as a function of time during the test from the data collected on these alloys. Factors affecting permeability measurements are discussed. Permeabilities are observed to vary throughout the experiment. This is attributed to microstructural coarsening and channeling that occurs in the sample during the experiment. The permeability is related to the microstructure of the sample using the Kozeny-Carman equation. The correlation between the measured K{sub s}, liquid fraction, g{sub L} and the specific solid surface area, S{sub v}, improves markedly when compared to previous studies in which microstructural coarsening was ignored.

Mercury was effectively removed from the oil via sorption using SAMMS.The method was demonstrated on a large scale using ORNL waste oil contaminated with mercury. This technology is ready for further demonstration and implementation when the SAMMS material is available in large quantities.

''The Murmansk Initiative - RF'' is a tri-lateral project developed to support Russia's ability to meet the London Convention's prohibition on ocean disposal of radioactive waste. The Initiative, under a tripartite agreement, has upgraded an existing low-level liquid radioactive waste treatment facility, increasing capacity from 1,200 m{sup 3}/year to 5,000 m{sup 3}/year, and expanded capability to treat liquids containing salt (up to 10 g/L). The three parties to the agreement, the Russian Federation, Norway, and the United States, have all contributed the project. All construction has been provided by Russia. Construction of mechanical systems (piping and valves, pumps, sorbent columns, settling tanks, and surge tanks) is nearing completion, with instrumentation and control (I&C) systems currently being installed. Delays to the I&C installation have occurred because changes in system specifications required additional U.S. supplied computer control equipment to be purchased, and clearance through customs (both U.S. and Russian) has been slow. Start-up testing has been limited to testing of isolated sub-systems because of the delays in the I&C installation. The current state of the Russian economy and completion of a cementation unit, which was not part of the original tri-partite agreement, have hampered final construction activities. Russian regulatory authorities have stated …

The U.S. Department of Energy will present an update and review of its programs in aluminum and magnesium for automotive and heavy-duty vehicle applications. While the main programs focused on vehicle materials are in the Office of Transportation Technologies, contributing efforts will be described in the DOE Office of Industrial Technologies and the DOE Office of Energy Research. The presentation will discuss materials for body/chassis and power train, and will highlight the considerable synergy among the efforts. The bulk of the effort is on castings, sheet, and alloys with a smaller focus on metal matrix composites. Cost reduction and energy savings are the overriding themes of the programs.

A series of bench-scale experiments were conducted to determine the optimum reaction conditions for destruction of styrene-divinyl benzene based cation resin and methylene chloride by the mediated electrochemical oxidation (MEO) process. Reaction parameters examined include choice of electron transfer mediator, reaction temperature and solvent system. For the cation exchange resins, maximum destruction efficiencies were obtained using cerium (IV) as mediator in nitric acid at a temperature of 70 C. Reasonable efficiencies were also realized with silver(II) and cobalt (III) at ambient temperature in the same solvent. Use of sulfuric acid as the solvent yielded much lower efficiencies under equivalent conditions. Methylene chloride was found to react only with silver (II) at ambient temperature in nitric acid media, cobalt (III) and cerium (IV) were totally ineffective. These results demonstrate a need to perform bench-scale experiments to determine optimum operating conditions for each organic substrate targeted for treatment by the MEO process.

In spite of recent advances in the mathematical modeling of fluid dynamics for materials processing applications, no significant advances have been made in the numerical discretization of these equations. In this work, the application of two-step projection methods for the numerical simulation of interdendritic flows is, discussed. Unlike previous methods, the methods presented here are constructed for the exact equations which are characterized by variable density and volumetric fraction of the liquid. The drag terms, which describe the momentum loss due to the flow around and through the dendrite structures, are treated implicitly. Numerical examples for shrinkage-induced flow during solidification of an AI-4.5% Cu alloy bar is used to illustrate the effectiveness of the proposed algorithm.

The authors have developed several different types of tools for sampling from sealed containers. These tools allow the user to rapidly drill into a closed container, extract a sample of its contents (gas, liquid, or free-flowing powder), and permanently reseal the point of entry. This is accomplished without exposing the user or the environment to the container contents, even while drilling. The entire process is completed in less than 15 seconds for a 55 gallon drum. Almost any kind of container can be sampled (regardless of the materials) with wall thicknesses up to 1.3 cm and internal pressures up to 8 atm. Samples can be taken from the top, sides, or bottom of a container. The sampling tools are inexpensive, small, and easy to use. They work with any battery-powered hand drill. This allows considerable safety, speed, flexibility, and maneuverability. The tools also permit the user to rapidly attach plumbing, a pressure relief valve, alarms, or other instrumentation to a container. Possible applications include drum venting, liquid transfer, container flushing, waste characterization, monitoring, sampling for archival or quality control purposes, emergency sampling by rapid response teams, counter-terrorism, non-proliferation and treaty verification, and use by law enforcement personnel during drug or …

Experiments are described in which a focused pulsed-excimer laser beam is used either to ablate a graphite target and deposit hydrogen-free amorphous carbon films, or to directly texture a silicon surface and produce arrays of high-aspect-ratio silicon microcolumns. In the first case, diamond-like carbon (or tetrahedral amorphous carbon, ta-C) films were deposited with the experimental conditions selected so that the masses and kinetic energies of incident carbon species were reasonably well controlled. Striking systematic changes in ta-C film properties were found. The sp{sup 3}-bonded carbon fraction, the valence electron density, and the optical (Tauc) energy gap ail reach their maximum values in films deposited at a carbon ion kinetic energy of {approximately}90 eV. Tapping-mode atomic force microscope measurements also reveal that films deposited at 90 eV are extremely smooth (rms roughness {approximately}1 {angstrom} over several hundred nm) and relatively free of particulate, while the surface roughness increases in films deposited at significantly lower energies. In the second set of experiments, dense arrays of high-aspect-ratio silicon microcolumns {approximately}20-40 {micro}m tall and {approximately}2 {micro}m in diameter were formed by cumulative nanosecond pulsed excimer laser irradiation of silicon wafers in air and other oxygen-containing atmospheres. It is proposed that microcolumn growth occurs through …