A truncated determinant algorithm is used to study the physical effects of the quark eigenmodes associated with eigenvalues below 300 MeV. This initial study focuses on coarse lattices (with O(a{sup 2}) improved gauge action), light internal quark masses and large physical volumes. Four bellweather full QCD processes are discussed: topological charge distributions, the eta prime propagator, string breaking as observed in the static energy and the rho decay into two pions.

The effect of possible accidental beam loss in LHC on the IP5 insertion elements and CMS detector is studied via realistic Monte Carlo simulations. Such beam loss could be the consequence of an unsynchronized abort or � in worst case � an accidental prefire of one of the abort kicker modules. Simulations with the STRUCT code show that this beam losses would take place in the IP5 inner and outer triplets. MARS simulations of the hadronic and electro-magnetic cascades induced in such an event indicate severe heating of the inner triplet quadrupoles. In order to protect the IP5 elements, two methods are proposed: a set of shadow collimators in the outer triplet and a prefired module compensation using a special module charged with an opposite voltage (antikicker). The remnants of the accidental beam loss entering the experimental hall have been used as input for FLUKA simulations in the CMS detector. It is shown that it is vital to take measures to reliably protect the expensive CMS tracker components.

A possibility to improve the Tevatron beam halo scraping using a bent channeling crystal instead of a thin scattering primary collimator is studied. To evaluate the efficiency of the system, realistic simulations have been performed using the CATCH and STRUCT Monte Carlo codes. It is shown that the scraping efficiency can be increased and the accelerator-related backgrounds in the CDF and DØ collider detectors can be reduced by about one order of magnitude. Results on scraping efficiency versus thickness of amorphous layer of the crystal, crystal alignment and its length are presented.

A 120 GeV Main Injector proton beam will be delivered to the NuMI beam line at Fermilab at the rate of 3.7x 10{sup 20} per year. Realistic Monte Carlo simulations have been performed to examine the radiation environment in the beam extraction system and NuMI beam line elements. A complete 3-D model of the 160 meter extraction region has been implemented utilizing the computer code MARS. The model includes a description of the field of the electrostatic septa and POISSON calculated field maps of the Lambertson magnets and the other lattice components in the area. The beam element alignment and the source term have been simulated using the code STRUCT. Results on beam losses in the system, energy deposition in the core elements and residual dose rates on the components are presented.

This work combines focused ion beam sputtering and ultra-precision machining as a first step in fabricating microstructure in metals and alloys. Specifically, {approx}25{micro}m diameter micro-end mills are made from cobalt M42 high-speed steel and C2 micrograin tungsten carbide tool blanks by ion beam sputtering. A 20 keV focused gallium beam defines tool cutting edges having radii of curvature < 0.1{micro}m. Micro-end mills having 2, 4 and 5 cutting edges successfully machine small trenches in 6061-T4 aluminum, brass, 4340 steel and polymethyl methacrylate. Machined trench widths are approximately equal to the tool diameters and surface roughnesses (rms) are {approx}150 nm or less. Microtools are robust and operate for more than 6 hours without fracture. Results from ultra-precision machining aluminum at feed rates as high as 50 mm/minute are included.

Analytical expressions used to optimize AR coatings for single junction solar cells are extended for use in monolithic, series interconnected multi-junction solar cell AR coating design. The result is an analytical expression which relates the solar cell performance (through J{sub sc}) directly to the AR coating design through the device reflectance. It is also illustrated how AR coating design be used to provide an additional degree of freedom for current matching multi-junction devices.

AR coating design for multi-junction solar cells can be more challenging than in the single junction case. Reasons for this are discussed. Analytical expressions used to optimize AR coatings for single junction solar cells are extended for use in monolithic, series interconnected multi-junction solar cell AR coating design. The result is an analytical expression which relates the solar cell performance (through J{sub SC}) directly to the AR coating design through the device reflectance. It is also illustrated how AR coating design can be used to provide an additional degree of freedom for current matching multi-junction devices.

The stacking of second and third layers of supercrystals of self-assembled passivated gold nanoparticles has been investigated using transmission electron microscopy. We report for the first time nanoparticles occupying the twofold saddle site in the third layer.

The spatial arrangement of sodium cations for a series of sodium phosphate glasses, xNa{sub 2}O(100-x)P{sub 2}O{sub 5} (x<55), were investigated using {sup 23}Na spin-echo NMR spectroscopy. The spin-echo decay rate is a function of the Na-Na homonuclear dipolar coupling and is related to the spatial proximity of neighboring Na nuclei. The spin-echo decay rate in these sodium phosphate glasses increases non-linearly with higher sodium number density, and thus provides a measure of the Na-Na extended range order. The results of these {sup 23}Na NMR experiments are discussed within the context of several structural models, including a decimated crystal lattice model, cubic dilation lattice model, a hard sphere (HS) random distribution model and a pair-wise cluster hard sphere model. While the experimental {sup 23}Na spin-echo M{sub 2} are described adequately by both the decimated lattice and the random HS model, it is demonstrated that the slight non-linear behavior of M{sub 2} as a function of sodium number density is more correctly described by the random distribution in the HS model. At low sodium number densities the experimental M{sub 2} is inconsistent with models incorporating Na-Na clustering. The ability to distinguish between Na-Na clusters and non-clustered distributions becomes more difficult at higher …

Monte Carlo simulations of phosphate tetrahedron connectivity distributions in alkali and alkaline earth phosphate glasses are reported. By utilizing a discrete bond model, the distribution of next-nearest neighbor connectivities between phosphate polyhedron for random, alternating and clustering bonding scenarios was evaluated as a function of the relative bond energy difference. The simulated distributions are compared to experimentally observed connectivities reported for solid-state two-dimensional exchange and double-quantum NMR experiments of phosphate glasses. These Monte Carlo simulations demonstrate that the polyhedron connectivity is best described by a random distribution in lithium phosphate and calcium phosphate glasses.

A series of single-well injection-withdrawal (SWIW) and two-well convergent-flow (TWCF) tracer tests were conducted in the Culebra dolomite at the WIPP site in late 1995 and early 1996. Modeling analyses over the past year have focused on reproducing the observed mass-recovery curves and understanding the basic physical processes controlling tracer transport in SWIW and TWCF tests. To date, specific modeling efforts have focused on five SWIW tests and one TWCF pathway at each of two different locations (H-11 and H-19 hydropads). An inverse parameter-estimation procedure was implemented to model the SWIW and TWCF tests with both traditional and multirate double-porosity formulations. The traditional model assumes a single diffusion rate while the multirate model uses a first-order approximation to model a continuous distribution of diffusion coefficients. Conceptually, the multirate model represents variable matrix block sizes within the Culebra as observed in geologic investigations and also variability in diffusion rates within the matrix blocks as observed with X-ray imaging in the laboratory. Single-rate double-porosity models cannot provide an adequate match to the SWIW data. Multirate double-porosity models provide excellent fits to all five SWIW mass-recovery curves. Models of the TWCF tests show that, at one location, the tracer test can be modeled …

A motion planning strategy was developed and implemented to generate motion control instructions from solid model data for controlling a robotically driven solid free-form fabrication process. The planning strategy was tested using a PUMA type robot arm integrated into a LENS{trademark} (Laser Engineered Net Shape) system. Previous systems relied on a series of x, y, and z stages, to provide a minimal coordinated motion control capability. This limited the complexity of geometries that could be constructed. With the coordinated motion provided by a robotic arm, the system can produce three dimensional parts by ''writing'' material onto any face of existing material. The motion planning strategy relied on solid model geometry evaluation and exploited robotic positioning flexibility to allow the construction of geometrically complex parts. The integration of the robotic manipulator into the LENS{trademark} system was tested by producing metal parts directly from CAD models.

In the period from April to October of 1988, a series of welding operations on the outside of the AZ Tank Farm ventilation line piping at the Hanford Site produced unexpected and repeated cracking of the austenitic stainless steel base metal and of a seam weld in the pipe. The ventilation line is fabricated from type 304L stainless steel pipe of 24 inch diameter and 0.25 inch wall thickness. The pipe was wrapped in polyethylene bubble wrap and buried approximately 12 feet below grade. Except for the time period between 1980 and 1987, impressed current cathodic protection has been applied to the pipe since its installation in 1974. The paper describes the history of the cracking of the pipe, the probable cracking mechanisms, and the recommended future action for repair/replacement of the pipe.

None

None

The electrical conductivities of boron carbides, B{sub 12+x}C{sub 3{minus}x} with 0.1 < x < 1.7, between 300 and 1200K suggest the hopping of a nearly temperature-independent density of small (bi)polarons. The activation energies of the nobilities are low, {approx} 0.16 eV, and are nearly independent of the composition. At lower temperatures, conductivities have non-Arrhenius temperature dependencies and strong sensitivity to carbon concentration. Percolative aspects of low-temperature hopping are evident in this sensitivity to composition. Boron carbides' Seebeck coefficients are anomalous in that (1) they are much larger than expected from boron carbides' large carrier densities and (2) they depend only weakly on the carrier density. Carrier-induced softening of local vibrations gives contributions to the Seebeck coefficient that mirror the magnitudes and temperature dependencies found in boron carbides.

We have conducted a fretting research project using MIL-L-87177 and CLT: X-10 lubricants on Nano-miniature connectors. When they were fretted without lubricant, individual connectors first exceeded our 0.5 ohm failure criteria from 2,341 to 45,238 fretting cycles. With additional fretting, their contact resistance increased to more than 100,000 ohms. Unmodified MIL-L-87177 lubricant delayed the onset of first failure to between 430,000 and over 20,000,000 fretting cycles. MIL-L-87177 modified by addition of Teflon powder delayed first failure to beyond 5 million fretting cycles. Best results were obtained when Teflon was used and also when both the straight and modified lubricants were poured into and then out of the connector. CLT: X-10 lubricant delayed the onset of first failure to beyond 55 million cycles in one test where a failure was actually observed and to beyond 20 million cycles in another that was terminated without failure. CLT: X-10 recovered an unlubricated connector driven deeply into failure, with six failed pins recovering immediately and four more recovering during an additional 420 thousand fretting cycles. MIL-L-87177 was not able to recover a connector under similar conditions.

Oak Ridge National Laboratory (ORNL) has been a major center of isotope production research, development, and distribution for over 50 years. Currently, the major isotope production activities include (1) the production of transuranium element radioisotopes, including 252 Cf; (2) the production of medical and industrial radioisotopes; (3) maintenance and expansion of the capabilities for production of enriched stable isotopes; and, (4) preparation of a wide range of custom-order chemical and physical forms of isotope products, particularly in accelerator physics research. The recent supply of and demand for isotope products and services in these areas, research and development (R&D), and the capabilities for future supply are described in more detail below. The keys to continuing the supply of these important products and services are the maintenance, improvement, and potential expansion of specialized facilities, including (1) the High Flux Isotope Reactor (HFIR), (2) the Radiochemical Engineering Development Center (REDC) and Radiochemical Development Laboratory (RDL) hot cell facilities, (3) the electromagnetic calutron mass separators and the plasma separation process equipment for isotope enrichment, and (4) the Isotope Research Materials Laboratory (IRML) equipment for preparation of specialized chemical and physical forms of isotope products. The status and plans for these ORNL isotope production facilities …

A sodalite/glass ceramic waste form has been developed to immobilize highly radioactive nuclear wastes in chloride form, as part of an electrochemical cleanup process. Simulated waste forms have been fabricated which contain plutonium and are representative of the salt from the electrometallurgical process to recover uranium from spent nuclear fuel. X-ray absorption fine structure spectroscopy (XAFS) and x-ray absorption near-edge spectroscopy (XANES) studies were performed to determine the location, oxidation state and form of the plutonium within these waste forms. Plutonium, in the non-fission-element case, was found to segregate as plutonium(IV) oxide with a crystallite size of at least 20 nm. With fission elements present, the crystallite size was about 2 nm. No plutonium was observed within the sodalite or glass in the waste form.

Statistical concepts, methods, and tools are often used in the implementation of statistical thinking. Unfortunately, statistical tools are all too often misused by not applying them in the context of statistical thinking that focuses on processes, variation, and data. The consequences of this misuse may be ''data torturing'' or going beyond reasonable interpretation of the facts due to a misunderstanding of the processes creating the data or the misinterpretation of variability in the data. In the hope of averting future misuse and data torturing, examples are provided where the application of common statistical tools, in the absence of statistical thinking, provides deceptive results by not adequately representing the underlying process and variability. For each of the examples, a discussion is provided on how applying the concepts of statistical thinking may have prevented the data torturing. The lessons learned from these examples will provide an increased awareness of the potential for many statistical methods to mislead and a better understanding of how statistical thinking broadens and increases the effectiveness of statistical tools.

We present a preliminary measurement of the electron angular distribution parameter {alpha}₂ in W {yields} e{nu} events using data collected by the D0 detector during the 1994-1995 Tevatron run. We compare our results with next-to- leading order perturbative QCD, which predicts an angular distribution of (1±{alpha}₁ cos{theta}* +{alpha}₂ cos²{theta}*), where {theta}* is the angle between the charged lepton and the antiproton in the Collins-Soper frame. In the presence of QCD corrections, the parameters {alpha}₁ and {alpha}₂ become functions of p^W_T , the W boson transverse momentum. We present the first measurement of {alpha}₂ as a function of p^W_T. This measurement is of importance, because it provides a test of next-to-leading order QCD corrections which are a non-negligible contribution to the W mass measurement.

Using data corresponding to an integrated luminosity of 79 pb{sup -1}, D0 has searched for events containing multiple jets and large missing transverse energy in p{bar p} collisions at {radical}s = 1.8 TeV at the Fermilab Tevatron collider. Observing no significant excess beyond what is expected from the standard model, they set limits on the masses of squarks and gluinos and on the model parameters m{sub 0} and m{sub 1/2}, in the framework of the minimal low-energy supergravity models of supersymmetry. For tan {beta} = 2 and A{sub 0} = 0, with {mu} < 0, they exclude all models with m{sub q} {approx} < 250 GeV/c{sup 2}. For models with equal squark and gluino masses, they exclude m < 260 GeV/c{sup 2}.

The most ambitious implementation of the Jefferson Lab data acquisition system (CODA) to date is for the CLAS spectrometer in Experimental Hall B. CLAS has over 40,000 instrumented channels and uses up to 30 front-end (FASTBUS/VME) crates in the DAQ subsystem. During the initial experiments the authors found that performance of the fully instrumented DAQ system did not scale as expected based on single point to point benchmarks. Over the past year the authors have been able to study various performance bottlenecks in the CLAS DAQ system including front-end real time performance, switched 100BaseT Ethernet data transport, and online data distribution and recording. Performance tuning was necessary for components on both real time (VxWorks) and UNIX (Solaris) operating systems. In addition, a new efficient Event Transfer System (ET) was developed to provide faster online monitoring while having minimal impact on data throughput to storage. They discuss these issues and efforts to overcome the real world problems associated with running a high performance DAQ system on a variety of commercial hardware and software.

The processes of defining managerial roles and providing for delegation of authority are essential to any enterprise. At most large organizations, these processes are defined in policy manuals and through sets of standard operating procedures for many, if not all, business and administrative functions. Many of these staff-initiated, administrative functions require the routing of documents for approval to one or more levels of management. These employee-oriented, back office types of workflows tend to require more flexibility in determining to whom these documents should go to, while, at the same time, providing the responsible parties with the flexibility to delegate their approval authority or allow others to review their work. Although this practice is commonplace in manual, paper-based processes that exist in many organizations, it is difficult to provide the same flexibility in the more structured, electronic-based, workflow systems.