Two types of fast bolometers are described for the plasma energy transport study in the Madison Symmetric Torus plasma confinement device. Both types use pyrocrystals of LiTaO[sub 3] or LiNbO[sub 3] as the sensors. One type is used for measurements of the radiated heat losses and is situated at the vacuum shell inner surface. Another type is insertable in the plasma and measures the plasma particle heat flux. The frequency response of the bolometers is measured to be in the 150--200 kHz range. The range of the measured power fluxes is 0.1 W/cm[sup 2] 10 kW/cm[sup 2] and can be adjusted by changing the size of the entrance aperture. The lower limit is determined by the amplifier noise and the frequency bandwidth, the higher limit by destruction of the bolometer sensor.

This report gives a general overview of the EGS[underscore]Windows2 program. The program is intended to be used to display individual particle histories of electrons, photons, and positrons generated by the EGS4 Code System. Much of this work is based on the earlier version of EGS[underscore]Windows2 from the Institute for National Measurement Standards at the National Research Council of Canada (NRCC). No attempt is made to modify their EGS subroutine WATCH, which is used to output the particle vectors to be read by EGS-Windows, or duplicate any of the documentation describing the subroutine. EGS[underscore]Windows2 reads data in the same format as produced by WATCH. Users of EGS[underscore]Windows2 are encouraged to obtain the original EGS[underscore]Windows report from the NRCC in addition to this report as complete documentation of EGS[underscore]Windows2. As in the original report, two levels of information are covered in this report: the user level, and the programmer level. The user level should be read by all users. It describes execution, operation, and capabilities. The programmer level should be read by those users who may want to modify the program or who would like a more detailed understanding. It describes briefly the routines and there function, as well as the major …

Objective is to understand the mechanisms governing nonequilibrium plasma atomistic or molecular deposition of hard face coatings. Laser diagnostic methods include coherent anti-Stokes Raman spectroscopy (CARS) and laser-induced fluorescence. TiB[sub 2] and diamonds were used as the hard face coating materials. Diborane was used as precursor to TiB[sub 2].

A variety of silyl- and alkyl-germylene precursors have been synthesized and subsequently pyrolyzed in the gas phase. Arrhenius parameters were obtained employing a pulsed-stirred flow reactor for these unimolecular decompositions. These precursors are divided into two major categories by mechanism of germylene extrusion: {alpha}-elimination precursors and germylacetylenes. The extrusion of germylenes from germylacetylene precursors is of primary interest. A mechanism is proposed employing a germacyclopropene intermediate. Evidence supporting this mechanism is presented. In the process of exploring germylacetylenes as germylene precursors, an apparent dyatropic rearrangement between germanium and silicon was observed. This rearrangement was subsequently explored.

This document is the fourth quarterly technical progress report under Contract No. DE-AC22-92PC92110, {open_quotes}Development of Vanadium-Phosphate Catalysts for Methanol Production by Selective Oxidation of Methane.{close_quotes} During this quarter, the authors focused primarily on catalyst activity testing in the microreactor. Additional blank runs using methane and methanol were performed. Initial attempts at preparing a silica supported catalyst are described. These results are discussed in detail and plans for the coming quarter are outlined.

The roughly 0.5-km{sup 2} (0.2-mi{sup 2}) Hanford Waste Vitrification Plant (WHVP) site is located in the Pasco Basin in south-central Washington State at the US Department of Energy`s Hanford Site. The HWVP site is planned for use as a waste treatment facility for treating the high-activity fraction of waste currently stored in underground storage tanks on the Hanford Site. In order to determine the pre-construction chemical properties of the proposed construction site soils and to enable the HWVP to segregate these, as necessary, from any impact of HWVP operations, a soil baseline sampling plan was written and implemented. The report describes the baseline sampling plan.

Element-specific magnetic hysteresis measurements on heteromagnetic materials have been achieved by using circularly polarized soft-x- rays. Dramatically different Fe and Co hysteresis curves of Fe/Cu/Co trilayers were obtained by recording the magnetic circular dichroism (MCD) at their respective L{sub 3} white lines as a function of applied magnetic field. The data resolve the complicated hysteresis curves, observed by conventional magnetometry, and determine the individual magnetic moments for the Fe and Co layers. Fine hysteresis features, imperceptible in the conventional curves, were also observed, demonstrating a new application of circularly polarized soft-x-rays in the investigation of magnetic systems.

Since its beginning, the Atmospheric Release Advisory Capability (ARAC), an emergency radiological dose assessment service of the US Government, has been called on to do consequence assessments for releases into the atmosphere of radionuclides and a variety of other substances. Some of the more noteworthy emergency responses have been for the Three Mile Island and Chernobyl nuclear power reactor accidents, and more recently, for a cloud of gases from a rail-car spill into the Sacramento river of the herbicide metam sodium, smoke from hundreds of burning oil wells in Kuwait, and ash clouds from the eruption of Mt. Pinatubo. The spatial scales of these responses range from local, to regional, to global, and the response periods from hours, to weeks, to months. Because of the variety of requirements of each unique assessment, ARAC has developed and maintains a flexible system of people, computer software and hardware.

Objective is to understand the mechanisms governing nonequilibrium plasma atomistic or molecular deposition of hard face coatings. Laser diagnostic methods include coherent anti-Stokes Raman spectroscopy (CARS) and laser-induced fluorescence. TiB{sub 2} and diamonds were used as the hard face coating materials. Diborane was used as precursor to TiB{sub 2}.

The Energy Information Administration (EIA), in cooperation with the US Geological Survey (USGS), has assessed 13 major petroleum producing regions outside of the United States. This series of assessments has been performed under EIA`s Foreign Energy Supply Assessment Program (FESAP). The basic approach used in these assessments was to combine historical drilling, discovery, and production data with EIA reserve estimates and USGS undiscovered resource estimates. Field-level data for discovered oil were used for these previous assessments. In FESAP, supply projections through depletion were typically formulated for the country or major producing region. Until now, EIA has not prepared an assessment of oil and gas provinces in the former Soviet Union (FSU). Before breakup of the Soviet Union in 1991, the Fergana basin was selected for a trial assessment of its discovered and undiscovered oil and gas. The object was to see if enough data could be collected and estimated to perform reasonable field-level estimates of oil and gas in this basin. If so, then assessments of other basins in the FSU could be considered. The objective was met and assessments of other basins can be considered. Collected data for this assessment cover discoveries through 1987. Compared to most other oil …

This program includes six tasks, including (1) a project measuring the performance of unique solar system components, (2) a project to develop a methodology for determining annual performance ratings of solar domestic hot water systems, (3) a project that will identify, analyze, design, build, and experimentally evaluate SDHW systems incorporating advanced concepts and components, (4) a liquid desiccant cooling system development project, (5) a project that will perform TRNSYS simulations to determine potential energy savings for desiccant cooling systems, especially in humid climates, and (6) a management task. The objectives and progress in each task are described.

Available thermodynamic data for volatilization of U and Pu gaseous species under oxidizing conditions are tabulated: UO{sub 3}, UO{sub 2}(OH){sub 2}, UO{sub 2}F{sub 2}, PuO{sub 3}, PuO{sub 2}(OH){sub 2}. Results of a thermodynamic analysis of U, Pu, and Am volatilities in the secondary combustor, plasma arc process, and vitrifier are given.

We have measured solute trapping of Sn in Al over a wide enough range of velocities to make a quantitative test of theory. The Continuous Growth Model of Aziz is the only one-parameter model that fits the data. We have also measured the diffusive speed - the growth rate at which interfacial partitioning is in mid-transition between equilibrium partitioning and complete solute trapping - for several solutes in A1. We have found an inverse correlation between the equilibrium partition coefficient and the diffusive speed. Taken together, these results give us heretofore unprecedented predictive capability in modeling rapid solidification processing. We have also examined theoretically short-range diffusion-limited growth, characteristic of incomplete solute trapping, and interface-limited growth, characteristic of complete solute trapping, in alloy solidification and have shown that the two regimes fall naturally out of a single unified theory of solidification.

Two types of fast bolometers are described for the plasma energy transport study in the Madison Symmetric Torus plasma confinement device. Both types use pyrocrystals of LiTaO{sub 3} or LiNbO{sub 3} as the sensors. One type is used for measurements of the radiated heat losses and is situated at the vacuum shell inner surface. Another type is insertable in the plasma and measures the plasma particle heat flux. The frequency response of the bolometers is measured to be in the 150--200 kHz range. The range of the measured power fluxes is 0.1 W/cm{sup 2} 10 kW/cm{sup 2} and can be adjusted by changing the size of the entrance aperture. The lower limit is determined by the amplifier noise and the frequency bandwidth, the higher limit by destruction of the bolometer sensor.

Research and development in support of the DWPF began during the 1970`s at the Savannah River Technology Center (formerly the Savannah River Laboratory). A large amount of data relevant to compliance with the Waste Acceptance Product Specifications (WAPS) was generated prior to the preparation and issue of the WAPS. Thus, most of this data was not generated under a quality assurance program which meets the Office of Civilian Radioactive Waste Management`s requirements. The DWPF has developed a plan for qualification of existing data sets which will be used to establish compliance with the WAPS, which is reported here. In this document, the existing data sets which will be used for compliance are identified, and the method(s) of qualification of each data set for use in the Waste Form Qualification Report is defined. This document thus provides a link between the detailed descriptions of all of the compliance activities in the Waste Form Compliance Plans (WCP), and the requirements for qualification of existing data sets used for compliance purposes. All of these data sets will be qualified by the end of Qualification Runs in the DWPF.

The investigations with the anion exchange resin Reillex{trademark}-HPQ is continuing along several different paths. The topics of current investigations that are reported here are: The sorption behavior of chromium(VI) on Reillex{trademark}-HPQ from nitric acid solutions and from sodium hydroxide/sodium nitrate solutions; sorption behavior of F{sup {minus}} on Reillex{trademark}-HPQ resin in acidic sodium nitrate solution; sorption behavior of Cl{sup {minus}} on Reillex{trademark}-HPQ resin in acidic sodium nitrate solution; sorption behavior of Br{sup {minus}} on Reillex{trademark}-HPQ resin in acidic sodium nitrate solution; and the Honors thesis by one of the students is attached as Appendix II (on ion exchange properties of a new macroperous resin using bromide as the model ion in aqueous nitrate solutions).

The intent of this paper is to cover as completely as possible and in sufficient detail the topics relevant to lead design. The first part identifies the problems associated with lead design, states the mathematical formulation, and shows the results of numerical and analytical solutions. The second part presents the results of a parametric study whose object is to determine the best choice for cooling method, material, and geometry. These findings axe applied in a third part to the design of high-current leads whose end temperatures are determined from the surrounding equipment. It is found that cooling method or improved heat transfer are not critical once good heat exchange is established. The range 5 < RRR < 100 is found to be acceptable for the relative resistivity ratio of the material. Use of high transition temperature super conductor materials is not warranted for this application. The optimal geometry (L:length, A:cross-section) for given current (1) follows the relation LI/A = 2 {times} 10{sup 5} but extends over a large of values. Mass flow needed to prevent thermal runaway varies linearly with current above a given threshold. Below that value, the mass flow is constant with current. Transient analysis shows no evidence …

The objectives of this project are to test novel fullerene based catalysts for application in methane activation. Fullerenes are a recently discovered allotrope of carbon that have been found to possess unusual properties, some of which may be ideal for methane conversion to higher hydrocarbons. The project is divided into three technical tasks. Task 1 deals with the synthesis and characterization of the fullerenes and fullerene soots, Task 2 with the testing of the catalysts, and Task 3 with the evaluation of the results and technical reporting requirements. This quarter we prepared fullerene soot and conducted experiments to determined its reactivity towards methane, hydrogen, and ethylene. The results are summarized: (1) Soot containing approximately 12-14 wt % fullerenes was prepared by the discharge method of Haufler et al. SRI is in the process of developing methodology to produce large scale amounts of fullerenes and fullerene based materials and is working with a private company to that end. In order to provide a background of fullerene soot and describe some of these methods we have included Appendix A. (2) We conducted some preliminary experiments in order to determine the temperature regime at which fullerene based soot would begin to be active …

Hydrogen generation data obtained from IDMS runs PX4 and PX5 will be used to determine a bases for a deflagration/detonation simulation in the DWPF CPC. This simulation is necessary due to the new chemistry associated with the Late Wash/ Nitric Acid flowsheet and process modifications associated with the presence of H{sub 2} in the offgas. The simulation will be performed by Professor Van Brunt from the University of South Carolina. The scenario which leads up to the deflagration/detonation simulation will be chosen such that the following conditions apply. The SRAT is filled to its maximum operating level with 9,600 gal of sludge, which corresponds to the minimum vapor space above the sludge. The SRAT is at the boiling point, producing H{sub 2} at a very low rate (about 10 % of the peak) and 15 scfm of air inleakage is entering the SRAT. Then, the H{sub 2} generation rate will be allowed to increase exponentially (catalyst activation) until it readies the peak H{sub 2} generation rate of the IDMS run, after which the H{sub 2} generation rate will be allowed to decay exponentially (catalyst deactivation) until the total amount of H2 produced is between 85 and 100% of that produced …

The Savannah River Technology Center created a second instance of its ORACLE based PEN LIMS to support site Environmental Restoration projects. The first instance of the database had been optimized for R&D support and did not implement rigorous sample tracking, verification, and holding times needed to support regulatory commitments. Much of the R&D instance was transferable such as the work control functions for backlog reports, work assignment sheets, and hazard communication support. A major enhancement of the regulatory LIMS was the addition of features to support a {open_quotes}standardized{close_quotes} electronic data format for environmental data reporting. The electronic format, called {open_quotes}AN92{close_quotes}, was developed by the site environmental monitoring organization and applies to both onsite and offsite environmental analytical contracts. This format incorporates EPA CLP data validation codes as well as details holding time and analytical result reporting requirements. The authors support this format by using special SQL queries to the database. The data is then automatically transferred to the environmental databases for trending and geological mapping.

I have reported most of the results of my adhesive testing to members of the VLPC design team at one time or another, usually verbally, but I am wnnng this summary as an easy reference to the results I obtained. The adhesives I tested were for two primary purposes. The first was adhering optical fibers to Torlon 7130; the other was for securing an aluminum nitride substrate to the same material. I have not had access to a scanning electron microscope and someone with the knowledge to determine actual failure mechanisms, so the deductions I have made about why some adhesives have worked well at low temperatures for some purposes and not for other applications while a different material never worked and another always worked are partially speculation. They should be taken merely at face value with no particular results 'carved in stone' so to speak. The first aspect of my testing was adhesion of optical fiber to torlon. Knowing that this is a very important joint, I tested a variety of glues of two primary types: acrylic and W cure. W cure adhesives are known to possess reasonably good properties at low temperatures and are quite convenient to use …

This report discusses research on nuclear masses and nuclear structure far from stability.

The Electric Power Monthly is prepared by the Survey Management Division; Office of Coal, Nuclear, Electric and Alternate Fuels, Energy Information Administration (EIA), Department of Energy. This publication provides monthly statistics at the US, Census division, and State levels for net generation, fossil fuel consumption and stocks, quantity and quality of fossil fuels, cost of fossil fuels, electricity sales, revenue, and average revenue per kilowatthour of electricity sold. Data on net generation, fuel consumption, fuel stocks, quantity and cost of fossil fuels are also displayed for the North American Electric Reliability Council (NERC) regions.

The Center for Accelerator Mass Spectrometry at LLNL has installed a new 64 position AMS sample changer on our spectrometer. This new sample changer has the capability of being controlled manually by an operator or automatically by the AMS data acquisition computer. Automatic control of the sample changer by the data acquisition system is a necessary step towards unattended AMS operation in our laboratory. The sample changer uses a fiber optic shaft encoder for rough rotational indexing of the sample wheel and a series of sequenced pneumatic cylinders for final mechanical indexing of the wheel and insertion and retraction of samples. Transit time from sample to sample varies from 4 s to 19 s, depending on distance moved. Final sample location can be set to within 50 microns on the x and y axis and within 100 microns in the z axis. Changing sample wheels on the new sample changer is also easier and faster than was possible on our previous sample changer and does not require the use of any tools.