Two dimensional (2-D) computation has been an accepted part of the design of accelerator magnets since the 1960's, but three-dimensional (3-D) computations are still not fully trusted. This paper describes the successes and limitations of 3-D computations, as applied to accelerator magnets for the Advanced Photon Source (APS) at Argonne National Laboratory (ANL). Both the finite element code TOSCA and the edge element volume integral code CORAL have been used in these computations. The ends of the dipole bending magnet for the injector synchrotron were designed using TOSCA; comparisons with measurements are described. Computation of other APS magnets are also described.

Three-dimensional finite element calculations in spherical geometry are performed to study the response of the mantle with platelike blocks at its surface to an initial condition corresponding to subduction along the margins of Pangea. The mantle is treated as an infinite Prandtl number Boussinesq fluid inside a spherical shell with isothermal, undeformable, free-slip boundaries. Nonsubducting rigid blocks to model continental lithosphere are included in the topmost layer of the computational mesh. At the beginning of the numerical experiments these blocks represent the present continents mapped to their approximate Pangean positions. Asymmetrical downwelling at the margins of these nonsubducting blocks results in a pattern of stresses that acts to pull the supercontinent apart. The calculations suggest that the breakup of Pangea and the subsequent global pattern of seafloor spreading was driven largely by the subduction at the Pangean margins.

Core samples taken from Hanford double-shell waste tank 101-SY during Window ``C`` (after the May 1991 gas release event) were analyzed for total organic carbon by the staff of the Analytical Chemistry Laboratory at Pacific Northwest Laboratory. The procedure uses the oxidation/extraction method of hot acid persulfate oxidation. Evolved CO{sub 2} is measured by a UIC Coulometric Carbon Analyzer coulometry detector. Samples are acidified with heated sulfuric acid to drive off all inorganic carbonate carbon as CO{sub 2}. Excess potassium persulfate oxidant, along with a silver catalyst, is then added to the heated sulfuric acid solution. All organic carbon is oxidized to CO{sub 2}, swept away by the carrier gas to the Coulometrics Analyzer, and the results calculated and displayed directly as {mu}g carbon titrated.

Core samples taken from Hanford double-shell waste tank 101-SY during Window C'' (after the May 1991 gas release event) were analyzed for total organic carbon by the staff of the Analytical Chemistry Laboratory at Pacific Northwest Laboratory. The procedure uses the oxidation/extraction method of hot acid persulfate oxidation. Evolved CO{sub 2} is measured by a UIC Coulometric Carbon Analyzer coulometry detector. Samples are acidified with heated sulfuric acid to drive off all inorganic carbonate carbon as CO{sub 2}. Excess potassium persulfate oxidant, along with a silver catalyst, is then added to the heated sulfuric acid solution. All organic carbon is oxidized to CO{sub 2}, swept away by the carrier gas to the Coulometrics Analyzer, and the results calculated and displayed directly as {mu}g carbon titrated.

The project provides a stepwise retrofit of an advanced overfire air (AOFA) system followed by low NO[sub x] burners (LNB). During each test phase of the project, diagnostic, performance, long-term, and verification testing will be performed. These tests are used to quantify the NO[sub x] reductions of each technology and evaluate the effects of those reductions on other combustion parameters such as particulatecharacteristics and boiler efficiency. Baseline, AOFA, and LNB without AOFA test segments have been completed. Analysis of the 94 days of LNB long-term data collected show the full-load NO[sub x] emission levels to be approximately 0.65 lb/MBtu. Flyash LOI values for the LNB configuration are approximately 8 percent at full-load. Corresponding values for the AOFA configuration are 0.94 lb/MBtu and approximately 10 percent. Abbreviated diagnostic tests for the LNB+AOFA configuration indicate that at 500 MWe, NO[sub x] emissions are approximately 0.55 lb/MBtu with corresponding flyash LOI values of approximately 11 percent. For comparison, the long-term full-load, baseline NO[sub x] emission level was approximately 1.24 lb/MBtu at 5.2 percent LOI. Comprehensive testing of the LNB+AOFA configuration will be performed when the stackparticulate emissions issue is resolved. Testing of a process optimization package on Plant Hammond Unit 4 was performed …

An engineering research and design competition to develop and demonstrate dedicated natural gas-powered light-duty trucks, the Natural Gas Vehicle (NGV) Challenge, was held June 6--11, 1191, in Oklahoma. Sponsored by the US Department of Energy (DOE), Energy, Mines, and Resources -- Canada (EMR), the Society of Automative Engineers (SAE), and General Motors Corporation (GM), the competition consisted of rigorous vehicle testing of exhaust emissions, fuel economy, performance parameters, and vehicle design. Using Sierra 2500 pickup trucks donated by GM, 24 teams of college and university engineers from the US and Canada participated in the event. A gasoline-powered control testing as a reference vehicle. This paper discusses the results of the event, summarizes the technologies employed, and makes observations on the state of natural gas vehicle technology.

This Options Analysis/Environmental Impact Statement (OA/EIS) identifies, presents effects of, and evaluates the potential options for changing instream flow levels in efforts to increase salmon populations in the lower Columbia and Snake rivers. The potential actions would be implemented during 1992 to benefit juvenile and adult salmon during migration through eight run-of-river reservoirs. The Corps of Engineers (Corps) prepared this document in cooperation with the Bonneville Power Administration and the Bureau of Reclamation. The US Fish and Wildlife Service (FSWS) is a participating agency. The text and appendices of the document describe the characteristics of 10 Federal projects and one private water development project in the Columbia River drainage basin. Present and potential operation of these projects and their effects on the salmon that spawn and rear in the Columbia and Snake River System are presented. The life history, status, and response of Pacific salmon to current environmental conditions are described.

This Options Analysis/Environmental Impact Statement (OA/EIS) identifies, presents effects of, and evaluates the potential options for changing instream flow levels in efforts to increase salmon populations in the lower Columbia and Snake rivers. The potential actions would be implemented during 1992 to benefit juvenile and adult salmon during migration through eight run-of-river reservoirs. The Corps of Engineers (Corps) prepared this document in cooperation with the Bonneville Power Administration and the Bureau of Reclamation. The US Fish and Wildlife Service (FWS) is a participating agency. The text and appendices of the document describe the characteristics of 10 Federal projects and one private water development project in the Columbia River drainage basin. Present and potential operation of these projects and their effects on the salmon that spawn and rear in the Columbia and Snake River System are presented. The life history, status, and response of Pacific salmon to current environmental conditions are described. The document concludes with an evaluation of the potential effects that could result from implementing proposed actions. The conclusions are based on evaluation of existing data, utilization of numerical models, and application of logical inference. This volume contains the appendices.

Detailed thermal stress analyses of beamline and optical components subject to high heat loads require an Accurate determination of the absorbed power profile for accurate prediction of the temperature profile and structural parameters. This is particularly important for high power beams from wigglers and undulators at the third generation synchrotron sources because components must, in general, be designed and maintained with strict mechanical tolerances. The spatial distribution of the power density of an undulator is a rapidly varying function of the energy of the photons suggesting that approximative methods based on a smooth spectral variation may not be valid. In this paper, a fast code for calculating undulator spectra is developed and compared with a wiggler code for approximation of the same spectra. Results from numerical simulations, including the emittance of the stored particle beam, are presented for the absorbed power density in a beryllium window. We find markedly different results for the two models for far off-axis radiation indicating the inadequacy of the wiggler model applied to an undulator spectrum in this case. The wiggler model overestimates the total absorbed power by as much as 82% for the beryllium window.

Static leach tests similar to PCT (Product Consistency Test) were performed for up to 2 years to assess long-term reaction behavior of high-level nuclear waste glasses similar to those at Defense Waste Processing Facility. These tests show the reaction rate to decrease with the reaction time from an initially high rate to a low rate, but then to accelerate to a higher rate after reaction times of about 1 year, depending on glass surface area/leachant volume ratio used. Solution concentrations of soluble glass components increase as the reaction is accelerated, while release of other glass components into solution is controlled by secondary phases. Net result is that transformation of glass to stable phases is accelerated while the solution becomes enriched in soluble components not effectively contained in secondary phases. Rate becomes linear in time after the acceleration and may be similar to the initial forward rate. A current model of glass reaction predicts that the glass reaction will be accelerated upon the formation of secondary phases which lower the silicic acid solution concentration. These tests show total Si concentration to increase upon reaction acceleration, however, which may be due to the slightly higher pH attained with the acceleration. The sudden …

The Accelerator Research Studies program at the University of Maryland, sponsored by the Department of Energy under grant number DE-FG05-91ER40642, is currently in the first year of a three-year funding cycle. The program consists of the following three tasks: TASK A, Study of Transport and Longitudinal Compression of Intense, High-Brightness Beams, TASK B, Study of Collective Ion Acceleration by Intense Electron Beams and Pseudospark Produced High Brightness Electron Beams; TASK C, Study of a Gyroklystron High-power Microwave Source for Linear Colliders. In this report we document the progress that has been made during the past year for each of the three tasks.

Every accelerator or storage ring system consists of a charged particle beam propagating through a beam line. Although a number of computer programs exits that simulate the propagation of a beam in a given beam line, only a few provide the capabilities for designing, commissioning and operating the beam line. This paper shows how a multi-track'' simulation and analysis code can be used for these applications.

Every accelerator or storage ring system consists of a charged particle beam propagating through a beam line. Although a number of computer programs exits that simulate the propagation of a beam in a given beam line, only a few provide the capabilities for designing, commissioning and operating the beam line. This paper shows how a ``multi-track`` simulation and analysis code can be used for these applications.

Iodine-129 is one of several long-lived reactor products that is being considered for transmutation by the Los Alamos Accelerator Transmutation of Waste (ATW) program. A reasonable rate of transmutation of 1291 is possible in this system because of the anticipated high neutron flux generated from the accelerator. This report summarizes previous papers dealing with the transmutation of 1291 where reactor technologies have been employed for neutron sources. The transmutation process is considered marginal under these conditions. Presented here are additional information concerning the final products that could be formed from the transmutation process in the ATW blanket. The transmutation scheme proposes the use of solid iodine as the target material and the escape of product xenon from the containers after van Dincklange (1981). Additional developmental plans are considered.

A Five-step methodology has been developed to evaluate information needs for nuclear power plants under accident conditions and the availability of plant instrumentation during severe accidents. Step 1 examines the credible accidents and their relationships to plant safety functions. Step 2 determines the information personnel involved in accident management will need to understand plant behavior. Step 3 determines the capability of the instrumentation to function properly under severe accident conditions. Step 4 determines the conditions expected during the identified severe accidents. Step 5 compares the instrument capabilities and the severe accident conditions to evaluate the availability of the instrumentation to supply needed plant information.

The Salton Sea reservoir, located in Imperial County, Ca., is unique in several ways from most liquid-dominated geothermal reservoirs that have been developed to date. One of these differences is the presence of hyper-saline brines containing up to 28% TDS (Total Dissolved Solids) and up to 0.2% NCG (Non-Condensible Gas). A simple material and energy balance model has been developed to study the effect of TDS and NCG on Salton Sea reservoir response. This study demonstrated that during the development of a two-phase system the partitioning of the NCG into the vapor phase and the consequential concentration of the TDS in the brine drastically alters the reservoir fluid properties. In modeling pressure depletion of hyper-saline reservoirs, such as the Salton Sea, these changes in reservoir fluid composition were shown to seriously affect the simulation results. As a result of these findings, a compositional fluid property package was developed using published data on H{sub 2}O-CO{sub 2}-NaCl mixtures. This fluid property package was then incorporated into the simulation program used by Unocal. Validation of the fluid property package in this simulation program was made using measured reservoir temperature, surface enthalpy, and surface flash data. The development of a compositional simulation program for …

There are job-specific training requirements established by regulations that Impose stringent training requirements on a contractor, for example, the Occupational Safety Health Act (OSHA). Failure to comply with OSHA training requirements can result in severe penalties being levied against a company. Although an accredited training program is expensive, it is a possible solution for minimizing risks associated with job-specific training requirements for employees. Operating DOE contractors direct approximately 10 percent of the operating funds toward training activities. Training needs for contractors span a broad range, from requirements awareness training for managers, to general training required on a one-time basis for all employees, to highly specialized training programs for employees involved In clean-up operations at hazardous waste sites. With this kind of an investment in training, it is logical to maximize the most return on an investment of training funds and to limit exposure to liability suits whenever possible. This presentation will provide an overview of accredited industrial safety programs. The criteria for accredited industrial safety programs will be defined. The question of whether accredited training programs are necessary will be examined. Finally, advantages and disadvantages will be identified for accrediting industrial safety training programs.

The solubility correlations for the H{sub 2}O-CO{sub 2} system applied so far for numerical simulation of geothermal reservoir and well flows are crude. This is due, at least partly, to the significant disagreement existing between the solubility models and results published in the specialized literature. In this work we analyze the reasons underlying this disagreement. On this basis, we propose a thermodynamically correct, and numerically accurate model for the solubility of carbon dioxide in water. Its range of validity is up to 350 C and 500 bar. Our main contributions are: (a) the adoption of an equation of state for the gas phase that realistically accounts for the non-ideal behavior of both components and that of the mixture, within the P-T range considered; and (b) to accurately include the effects of temperature and pressure on the solubility of carbon dioxide in the liquid phase. The proposed model fits the available phase equilibrium data for the H{sub 2}O-CO{sub 2} system nicely. In particular, it does not present the severe conflict between the linearity of the model and the lack of linearity of the data, evident in earlier models. The tight fit obtained with our model indicates that the complexities of H{sub …

We have developed a new measurement technique to improve the accuracy and sensitivity of the nondestructive assay (NDA) of plutonium scrap and waste. The 200-{ell} drum assay system uses the classical NDA method of counting passive-neutron coincidences from plutonium but has added the new features of add-a-source'' to improve the accuracy for matrix corrections and statistical techniques to improve the low-level detectability limits. The add-a-source technique introduces a small source of {sup 252}Cf (10{sup {minus}8} g) near the external surface of the sample drum. The drum perturbs the rate at which coincident neutrons from the {sup 252}Cf are counted. The perturbation provides the data to correct for the matrix and plutonium inside the drum. The errors introduced from matrix materials in 200-{ell} drums have been reduced by an order of magnitude using the add-a-source technique. In addition, the add-a-source method can detect unexpected neutron-shielding material inside the drum that might hide the presence of special nuclear materials. The detectability limit of the new waste-drum assay system for plutonium is better than prior systems for actual waste materials. For the in-plant installation at a mixed-oxide fabrication facility, the detectability limit is 0.73 mg of {sup 24O}Pu (or 2.3 mg of high-burnup …

Estimates for the pressure decline in high TDS geothermal fluids containing dissolved gases are extremely sensitive to the PVT representation of the reservoir fluid. Significant errors in predicted pressures will occur if the geothermal fluid is represented by one or two pseudo components with modified water properties. As a result, we have developed a PVT model to predict the thermodynamic properties of a prototype geothermal fluid as represented by three-component H{sub 2}O-CO{sub 2}-NaCl mixtures. The range of applicability of the model is: Temperatures from 75 to 700+ F, pressures from 14.7 to 5000 psi, carbon dioxide content from 0-5 wt%, and salt concentrations to 30 wt%. The model has been implemented into Unocal's version of a commercially available reservoir simulator and is currently being used to study one of Unocal's high salinity reservoirs located in the Imperial Valley of California.

This paper describes the ACPMAPS computing system -- its purpose, its hardware architecture, how the system is used, and relevant programming paradigms and concepts. Features of the hardware and software will be discussed in some detail, both quantitative and qualitative. This should give some perspective as to the suitability of the ACPMAPS system for various classes of applications, and as to where this system stands in the spectrum of today's supercomputers. The ACPMAPS project at Fermilab was initiated in 1987 as a collaborations between the Advanced Computer Program (now the Computer R D department) and the lattice gauge physicists in the Theory department. ACPMAPS is an acronym for Advanced Computer Program Multiple Array Processor System -- this acronym is no longer accurate, but the name has stuck. Although research physics computations were done on ACPMAPS as early as 1989, the full-scale system was commissioned as a reliable physics tool in early 1991. The original ACPMAPS was a 5 Gflop (peak) system. An upgrade by a factor of ten in computer power and memory size, but substituting a new CPU board, will occur during early 1991 -- this is referred to as the new ACPMAPS Upgrade or 50 GF ACPMAPS. The …

Transport of alkali metal atoms through porous cathodes of alkali metal thermal-to-electric converter (AMTEC) cells is responsible for significant, reducible losses in the electrical performance of these cells. Experimental evidence for activated transport of metal atoms at grain surfaces and boundaries within some AMTEC electrodes has been derived from temperature dependent studies as well as from analysis of the detailed frequency dependence of ac impedance results for other electrodes, including thin, mature molybdenum electrodes which exhibit transport dominated by free molecular flow of sodium gas at low frequencies or dc conditions. Activated surface transport will almost always exist in parallel with free molecular flow transport, and the process of alkali atom adsorption/desorption from the electrode surface will invariably be part of the transport process, and possibly a dominant part in some cases. Little can be learned about the detailed mass transport process from the ac impedance or current voltage curves of an electrode at one set of operating parameters, because the transport process includes a number of important physical parameters that are not all uniquely determined by one experiment. The temperature dependence of diffusion coefficient of the alkali metal through the electrode in several cases provides an activation energy and …

The LVQ algorithm is a common method which allows a set of reference vectors for a distance classifier to adapt to a given training set. We have developed a similar learning algorithm, LVQ-MM, which manipulates hyperellipsoidal cluster boundaries as opposed to reference vectors. Regions of the input feature space are first enclosed by ellipsoidal decision boundaries, and then these boundaries are iteratively modified to reduce classification error. Results obtained by classifying the Iris data set are provided.

Perfect crystal monochromators cannot diffract x-rays efficiently, nor transmit the high source brightness available at synchrotron radiation facilities, unless surface strains within the beam footprint are maintained within a few arcseconds. Insertion devices at existing synchrotron sources already produce x-ray power density levels that can induce surface slope errors of several arcseconds on silicon monochromator crystals at room temperature, no matter how well the crystal is cooled. The power density levels that will be produced by insertion devices at the third-generation sources will be as much as a factor of 100 higher still. One method of restoring ideal x-ray diffraction behavior, while coping with high power levels, involves adaptive compensation of the induced thermal strain field. The design and performance, using the X25 hybrid wiggler beam line at the National Synchrotron Light Source (NSLS), of a silicon crystal bender constructed for this purpose are described.