Resource Type

Radionuclides in plankton from the South Pacific Basin (open access)

Radionuclides in plankton from the South Pacific Basin

We have initiated an investigation of the utility of marine plankton as bioconcentrating samplers of low-level marine radioactivity in the southern hemisphere. A literature review has shown that both freshwater and marine plankton have trace element and radionuclide concentration factors (relative to water) of up to 10/sup 4/. We participated in Operations Deepfreeze 1981 and 1982, collecting a total of 48 plankton samples from the USCGC Glacier on its Antarctic cruises. Battelle Pacific Northwest Laboratories sampled air, water, rain, and fallout. We were able to measure concentrations in plankton of the naturally-occurring radionuclides /sup 7/Be, /sup 40/K, and the U and Th series, and we believe that we have detected low levels of /sup 144/Ce and /sup 95/Nb in seven samples ranging as far south as 68/sup 0/. Biological identification of the plankton suggests a possible correlation between radionuclide concentration and the protozoa content of the samples. 7 references, 5 figures.
Date: March 23, 1984
Creator: Marsh, K.V. & Buddemeier, R.W.
System: The UNT Digital Library
Quantitative analysis of the hydrothermal system in Lassen Volcanic National Park and Lassen Known Geothermal Resource Area (open access)

Quantitative analysis of the hydrothermal system in Lassen Volcanic National Park and Lassen Known Geothermal Resource Area

The Lassen hydrothermal system is in the southern Cascade Range, approximately 70 kilometers east-southeast of Redding, California. The conceptual model of the Lassen system is termed a liquid-dominated hydrothermal system with a parasitic vapor-dominated zone. The essential feature of this model is that steam and steam-heated discharge at relatively high elevations in Lassen Volcanic National Park (LVNP) and liquid discharge with high chloride concentrations at relatively low elevations outside LVNP in the Lassen Known Geothermal Resource Area (KGRA) are both fed by an upflow of high-enthalpy, two-phase fluid within the Park. Liquid flows laterally away from the upflow area towards the areas of high-chloride discharge, and steam rises through a vapor-dominated zone to feed the steam and steam-heated features. The geometric model corresponds to an areally restricted flow regime that connects the Bumpass Hell area in LVNP with regions of chloride hot springs in the Mill Creek canyon in the KGRA south of LVNP. Simulations of thermal fluid withdrawal in the Mill Creek Canyon were carried out in order to determine the effects of such withdrawal on portions of the hydrothermal system within the Park. 19 refs., 17 figs., 4 tabs.
Date: January 1, 1984
Creator: Sorey, M.L. & Ingebritsen, S.E.
System: The UNT Digital Library
Pacific Northwest Laboratory, annual report for 1983 to the DOE Office of Energy Research. Part 4. Physical sciences (open access)

Pacific Northwest Laboratory, annual report for 1983 to the DOE Office of Energy Research. Part 4. Physical sciences

Part 4 of the Pacific Northwest Laboratory Annual Report for 1983 to the Office of Energy Research, includes those programs funded under the title Physical and Technological Research. The Field Task Program Studies reports in this document are grouped under the subheadings and each section is introduced by a divider page that indicates the Field Task Agreement reported in that section. These reports only briefly indicate progress made during 1983. The reader should contact the principal investigators named or examine the publications cited for more details.
Date: February 1, 1984
Creator: unknown
System: The UNT Digital Library
Interactions of tailings leachate with local liner materials found at Canonsburg, Pennsylvania. (open access)

Interactions of tailings leachate with local liner materials found at Canonsburg, Pennsylvania.

The mill tailings site at Canonsburg, Pennsylvania is the first mill site to receive remedial action under the Department of Energy's Uranium Mill Tailings Remedial Action Program. Part of this remedial action will require excavating the 53,500 m/sup 3/ (70,000 yd/sup 3/) of tailings on the site having a specific activity exceeding 100 pCi/g, and encapsulating these contaminated tailings in a clay-lined cell. As part of the remedial action effort, Pacific Northwest Laboratory has been studying the interactions of tailings and tailings leachate with locally occurring clays proposed for liner materials. These studies include physical and chemical characterization of amended and unamended local clays, chemical characterization of the tailings, column studies of tailings leached with deionized water, and column studies of clays contacted with tailings solutions to determine the attenuation properties of the proposed liner materials. Column studies of tailings leached with deionized water indicated that the Canonsburg tailings could represent a source of soluble radium-226 and uranium-238, several trace metals, cations, and the anions SO/sub 4/, NO/sub 3/, and Cl. Of these soluble contaminants, uranium-238, radium-226, the trace metals As and Mo, and the anions F and SO/sub 4/ were present at levels exceeding maximum concentration levels in the …
Date: April 1, 1984
Creator: Dodson, M.E.; Gee, G.W. & Serne, R.J.
System: The UNT Digital Library
Retrospective examination of geothermal environmental assessments (open access)

Retrospective examination of geothermal environmental assessments

Since 1976, the Department of Energy (DOE) has supported a variety of programs and projects dealing with the exploration, development, and utilization of geothermal energy. This report presents an overview of the environmental impacts associated with these efforts. Impacts that were predicted in the environmental analyses prepared for the programs and projects are reviewed and summarized, along with measures that were recommended to mitigate these impacts. Also, for those projects that have gone forward, actual impacts and implemented mitigation measures are reported, based on telephone interviews with DOE and project personnel. An accident involving spills of geothermal fluids was the major environmental concern associated with geothermal development. Other important considerations included noise from drilling and production, emissions of H/sub 2/S and cooling tower drift, disposal of solid waste (e.g., from H/sub 2/S control), and the cumulative effects of geothermal development on land use and ecosystems. Mitigation measures were frequently recommended and implemented in conjunction with noise reduction; drift elimination; reduction of fugitive dust, erosion, and sedimentation; blowout prevention; and retention of wastes and spills. Monitoring to resolve uncertainties was often implemented to detect induced seismicity and subsidence, noise, drift deposition, concentrations of air and water pollutants, and effects on groundwater. …
Date: March 1, 1984
Creator: Webb, J. W.; Eddlemon, G. K. & Reed, A. W.
System: The UNT Digital Library
Murakami density limit in tokamaks and reversed-field pinches (open access)

Murakami density limit in tokamaks and reversed-field pinches

A theoretical upper limit for the density in an ohmically heated tokamak discharge follows from the requirement that the ohmic heating power deposited in the central current-carrying channel exceed the impurity radiative cooling in this critical region. A compact summary of our results gives this limit n/sub M/ for the central density as n/sub M/ = (Z/sub e//(Z/sub e/-1)/sup 1/2/n/sub eo/ (B/sub T//1T)(1m/R) where n/sub eo/ depends strongly on the impurity species and is remarkably independent of the central electron temperature T/sub e/(0). For T/sub e/(0) approx. 1 keV, we have n/sub eo/ = 1.5 x 10/sup 14/ cm/sup -3/ for beryllium, n/sub eo/ = 5 x 10/sup 13/ cm/sup -3/ for oxygen, n/sub eo/ = 1.0 x 10/sup 13/ cm/sup -3/ for iron, and n/sub eo/ = 0.5 x 10/sup 13/ cm/sup -3/ for tungsten. The results agree quantitatively with Murakami's original observations. A similar density limit, known as the I/N limit, exists for reversed-field pinch devices and this limit has also been evaluated for a variety of impurity species.
Date: March 1, 1984
Creator: Perkins, F.W. & Hulse, R.A.
System: The UNT Digital Library
Second Nuclear Era (open access)

Second Nuclear Era

The Institute for Energy Analysis with support from The Andrew W. Mellon Foundation has studied the decline of the present nuclear era in the United States and the characteristics of a Second Nuclear Era which might be instrumental in restoring nuclear power to an appropriate place in the energy options of our country. The study has determined that reactors operating today are much safer than they were at the time of the TMI accident. A number of concepts for a supersafe reactor were reviewed and at least two were found that show considerable promise, the PIUS, a Swedish pressurized water design, and a gas-cooled modular design of German and US origin. Although new, safer, incrementally improved, conventional reactors are under study by the nuclear industry, the complete lack of new orders in the United States will slow their introduction and they are likely to be more expensive than present designs. The study recommends that supersafe reactors be taken seriously and that federal and private funds both be used to design and, if feasible, to build a prototype reactor of substantial size. 146 references, 8 figures, 2 tables.
Date: March 1, 1984
Creator: Weinberg, Alvin M.; Spiewak, Irving; Barkenbus, Jack N.; Livingston, Robert S. & Phung, Doan L.
System: The UNT Digital Library
Mechanical transport in two-dimensional networks of fractures (open access)

Mechanical transport in two-dimensional networks of fractures

The objectives of this research are to evaluate directional mechanical transport parameters for anisotropic fracture systems, and to determine if fracture systems behave like equivalent porous media. The tracer experiments used to measure directional tortuosity, longitudinal geometric dispersivity, and hydraulic effective porosity are conducted with a uniform flow field and measurements are made from the fluid flowing within a test section where linear length of travel is constant. Since fluid flow and mechanical transport are coupled processes, the directional variations of specific discharge and hydraulic effective porosity are measured in regions with constant hydraulic gradients to evaluate porous medium equivalence for the two processes, respectively. If the fracture region behaves like an equivalent porous medium, the system has the following stable properties: (1) specific discharge is uniform in any direction and can be predicted from a permeability tensor; and (2) hydraulic effective porosity is directionally stable. Fracture systems with two parallel sets of continuous fractures satisfy criterion 1. However, in these systems hydraulic effective porosity is directionally dependent, and thus, criterion 2 is violated. Thus, for some fracture systems, fluid flow can be predicted using porous media assumptions, but it may not be possible to predict transport using porous media …
Date: April 1, 1984
Creator: Endo, H.K.
System: The UNT Digital Library
Inspection of the Heber binary-cycle geothermal project (open access)

Inspection of the Heber binary-cycle geothermal project

We concluded that DOE had effective management control procedures to monitor project costs and the design, construction and demonstration activities. Lessons learned from previous DOE geothermal projects were applied and technical information generated from the Heber plant will be transferred to the public and private sectors by the project participants. We also identified the following issues that concerned us: Revenue Sharing: under existing revenue sharing provisions in the Cooperative Agreement, we estimate that reimbursable revenues to DOE will range between $30.5 million and $51.6 million. DOE and the public should be reimbursed for the total contribution of $61 million because the plant, if commercialized, will primarily benefit ratepayers and stockholders of San Diego Gas and Electric Company (SDG and E); Project Office Support Contracts: Our analyses of a number of project office support contracts suggest that some of this work should be cost shared with SDG and E; in other cases, the value of the work is questionable and appears to be an unnecessary expenditure of DOE funds; and Questionable Contractor Procurement: the noncompetitive procurement of a private firm to develop an economic study of a second Heber plant appears to be unjustified and duplicates work already planned by project …
Date: March 28, 1984
Creator: unknown
System: The UNT Digital Library
Analysis of fracture modes during extrusion and drawing of bimetal rods or wire. Analytical study of drawing and extrusion of superconducting filamentary wires: fracture problems and evaluation of temperature rise. Final report (open access)

Analysis of fracture modes during extrusion and drawing of bimetal rods or wire. Analytical study of drawing and extrusion of superconducting filamentary wires: fracture problems and evaluation of temperature rise. Final report

Based on the upper-bound theorem in limit analysis, a theoretical model describing sound flow, core fracture, and sleeve fracture in bimetal rods and wire during extrusion and drawing was developed. The variables affecting core and sleeve fracture are: reduction in area, die geometry, friction, relative size and strength of the core, and applied surface tractions. Within the wide range of combinations of these process variables, only a small range permits co-extrusion and codrawing without fracture. Criteria for the prevention of core and sleeve fracture during co-extrusion and core fracture during co-drawing were developed and presented graphically in this study. The results were applied to the central burst problem during extrusion and drawing of homogeneous materials.
Date: January 9, 1984
Creator: Avitzur, B.; Wu, R.; Chou, Y.T. & Talbert, S.
System: The UNT Digital Library
Case study of the Wendel-Amedee Exploration Drilling Project, Lassen County, California, User Coupled Confirmation Drilling Program (open access)

Case study of the Wendel-Amedee Exploration Drilling Project, Lassen County, California, User Coupled Confirmation Drilling Program

The Wendel-Amedee KGRA is located in Honey Lake basin in Lassen County, California, on the boundary between the Modoc Plateau and the Basin and Range geologic provinces. A variety of geophysical surveys was performed over the project property. Geophysical data helped in establishing the regional structural framework, however, none of the geophysical data is sufficiently refined to be considered suitable for the purpose of siting an exploration drill hole. Drilling of reservoir confirmation well WEN-1 took place from August 1 to September 22, 1981. Pulse and long-term flow testing subjected the reservoir to a maximum flow of 680 gpm for 75 hours. At that rate, the well exhibited a productivity index of 21.6 gpm/psi; the reservoir transmissivity was 3.5 x 10/sup 6/ md-ft/cp. The maximum bottom-hole temperature recorded during testing was 251/sup 0/F. The conceptual model of the geothermal resource at Wendel Hot Springs calls on ground water, originating in the neighboring volcanic highlands, descending through jointed and otherwise permeable rocks into the granitic basement. Once in the basement, the fluid is heated as it continues its descent, and lateral movement as dictated by the hydrologic gradient. It then rises to the discharge point along transmissive faults. 45 refs., 28 …
Date: September 1, 1984
Creator: Zeisloft, J.; Sibbett, B.S. & Adams, M.C.
System: The UNT Digital Library
Structural materials for breeder reactor cores and coolant circuits (open access)

Structural materials for breeder reactor cores and coolant circuits

The structural components of principal interest in LMFBR cores and cooling circuits include the reactor vessel, primary and secondary piping, intermediate heat exchanger (IHX), and steam generator. Load-bearing components inside the vessel, among these the fuel cladding and duct, are also included. The operating conditions present in a fast-breeder nuclear reactor impose a number of requirements on the mechanical, physical, and neutronic properties of the materials used to construct these components.
Date: February 1, 1984
Creator: Diercks, D. R.
System: The UNT Digital Library
Fermilab 200 MeV linac control system hardware (open access)

Fermilab 200 MeV linac control system hardware

This report is a description of the present Linac distributed control system that replaces the original Xerox computer and interface electronics with a network of 68000-based stations. In addition to replacing the obsolete Xerox equipment, goals set for the new system were to retain the fast response and interactive nature of the original system, to improve reliability, to ease maintenance, and to provide 15 Hz monitoring of all Linac parameters. Our previous experience with microcomputer installations showed that small, stand-alone control systems are rather straightforward to implement and have been proven to be reliable in operation, even in the severe environment of the 750-keV preaccelerator. The overall design of the Linac system incorporates the concept of many relatively small, stand-alone control systems networked together using an intercomputer communication network. Each station retains its local control system character but takes advantage of the network to allow an operator to interact with the entire Linac from any local console. At the same time, a link to the central computer system allows Host computers to also access parameters in the Linac.
Date: January 1, 1984
Creator: Shea, M.F.
System: The UNT Digital Library
Direct spectroscopic observation of charge-exchange recombination of medium-Z elements in the PLT tokamak (open access)

Direct spectroscopic observation of charge-exchange recombination of medium-Z elements in the PLT tokamak

We report the first observation of line emission resulting directly from charge-exchange recombination of medium-Z elements (Al, Sc) injected into a PLT discharge. Transitions due to the radiative cascade immediately following charge-exchange of He-like Al and Sc were observed by a VUV spectrograph and two air monochromators. In two cases, AlXI 3209 A and ScXIX 112.1 A, the observed transition had not previously been experimentally identified. Spatial scans provided information on the profile of the neutral beam in the plasma.
Date: March 1, 1984
Creator: Skinner, C. H.; Suckewer, S.; Cohen, S. A.; Schilling, G.; Wilson, R. & Stratton, B.
System: The UNT Digital Library
Oxidation/gasification of carbon residue on retorted oil shale. Final report (open access)

Oxidation/gasification of carbon residue on retorted oil shale. Final report

Studies of the oxidation and gasification of oil shale char were extended to an investigation of the effects of mineral catalysis. Six shales with differing mineral compositions were studied, including samples from the saline zone in the Western Colorado and from the Antrim shales of Michigan. Oxidation kinetics data, corrected for mass transfer effects, were compared for all six samples. A high assay shale from Utah and a sample from the saline zone were found to have the highest oxidation rates. By examining the data for shales which were water leached and thermally pretreated, it was concluded that both NaO and CaO act as oxidation catalysts. However, as a result of mineral decomposition experiments conducted with a sample from the C-a lease tract, it appears as though the ankeritic dolomite fraction will not decompose as long as there is a minimal CO/sub 2/ over pressure. Rather, low temperature silication reactions appear to take place once the temperature exceeds 925/sup 0/K. An extensive evaluation was also completed for the gasification of an Antrim shale from Michigan. Both the rates of CO/sub 2/ and steam gasification of the char were found to be markedly lower than that observed for a shale sample …
Date: January 16, 1984
Creator: Thomson, W. J.
System: The UNT Digital Library
Cumulative Effects of Micro-Hydro Development on the Fisheries of the Swan River Drainage, Montana, First Annual Progress Report (Covering Field Season July-November 1982). (open access)

Cumulative Effects of Micro-Hydro Development on the Fisheries of the Swan River Drainage, Montana, First Annual Progress Report (Covering Field Season July-November 1982).

This fisheries study is to determine the potential cumulative biological and economic effects of 20 small or micro-hydro-electric facilities (less than 5 megawatts) proposed to be constructed on tributaries to the Swan River, a 1738 square kilometer (671 square mile) drainage located in northwestern Montana. The study addresses portions of measure 1204 (b) (2) of the Norwthwest Power Planning Council's Columbia River Basin Fish and Wildlife Program. Aerial pre-surveys conducted during 1982 identified 102 stream reaches that may support fish populations in the Swan drainage between Swan and Lindbergh lakes. These reaches were located in 49 tributary streams and constituted 416 kilometers (258 miles) of potential fish habitat. Construction of all proposed small hydro projects would divert water from 54 kilometers (34 miles) or about 13 percent of the tributary system. Only two of the 20 proposed hydro sites did not support trout populations and most were populated by migratory bull trout and westslope cutthroat trout. Potential cumulative habitat losses that could result from dewatering of all proposed project areas were predicted using a stream reach classification scheme involving stream gradient, drainage ara, and fish population data. Preliminary results of this worst case analysis indicate that 23, 19 and 6 …
Date: March 1, 1984
Creator: Leathe, Stephen A. & Graham, Patrick J.
System: The UNT Digital Library
One-dimensional code to predict the thermal behavior of the UTSI MHD radiant furnace (open access)

One-dimensional code to predict the thermal behavior of the UTSI MHD radiant furnace

An analytical model of the thermal behavior of the radiant furnace components installed in the CFFF has been developed. Efforts have been primarily directed towards obtaining a representative global evaluation of the heat recovery of the major downstream components. An overall review of the heat transfer code developed specifically for the DOE CFFF downstream components is presented. The basic methods by which the gas state, transport properties, and the thermal radiative and convective properties are calculated are delineated. Since the thermal behavior of the furnace is radiation dominated, a greater emphasis was placed on this mode of heat transfer. The heat transfer model employs a single zone approximation to the physical problem. The results of the code show good agreement with the experimental data. A more rigorous approach to the problem requires the use of a multi-zone analysis which is presently under consideration. 21 references. (WHK)
Date: March 1, 1984
Creator: Galanga, F.L.
System: The UNT Digital Library
Heteroatom speciation in coal liquefaction via FTIR coupled with liquid chromatography. Quarterly progress report, October 1-December 31, 1983 (open access)

Heteroatom speciation in coal liquefaction via FTIR coupled with liquid chromatography. Quarterly progress report, October 1-December 31, 1983

The objectives of the research are (1) evaluate the potential of FT-IR for qualitative functional group detection in chromatographic fractions of highly polar materials, (2) develop separation techniques with the aid of FT-IR detection for concentration of oxygen, nitrogen and sulfur functionalities in synfuels, (3) describe and quantify the various heteroatom functionalities in selected solvent refined coal fractions, (4) place speciation techniques on-line with chromatographic separations, (5) compare quantitative speciation information obtained from LC-FTIR with established fluorine tagging techniques regarding model compounds and synfuels. 23 figures, 5 tables.
Date: May 1, 1984
Creator: Taylor, L.T.
System: The UNT Digital Library
Management and organizational assessments: a review of selected organizations (open access)

Management and organizational assessments: a review of selected organizations

This report is part of a larger project designed to assist the NRC in its responsibilities for assessing the management and organization of utilities applying for an operating license for a nuclear power plant. This report reviews the processes and criteria used by other organizations that conduct management and organization audits and evaluations. It was undertaken in order to provide data and a basis for future analysis by taking a comparative perspective. When considering changes in criteria and procedures as the NRC is doing, a standard benchmark is the performance of other organizations that are similarly situated. It was our goal to directly inform the NRC about the activities of other organizations so that a reconsideration of NRC activities could benefit from the perspective of organizations with a longer, broader, and different experience than the NRC has in the management and organization area. Data collected for this report has provided useful information in designing organization and administration guidelines and assessment procedures for consideration by the NRC.
Date: February 1, 1984
Creator: Nadel, M. V. & Kerwin, C. M.
System: The UNT Digital Library
DAS performance analysis (open access)

DAS performance analysis

This report begins with an overview of the Data Acquisition System (DAS), which supports several of PPPL's experimental devices. Performance measurements which were taken on DAS and the tools used to make them are then described.
Date: February 1, 1984
Creator: Bates, G.; Bodine, S.; Carroll, T. & Keller, M.
System: The UNT Digital Library
Long term materials test program. Quarterly report, April-June 1983 (open access)

Long term materials test program. Quarterly report, April-June 1983

Corrosion and erosion/corrosion testing of gas turbine materials in the effluent from a pressurized fluidized bed coal combustor continues under the Long Term Materials Test program. Two 1000-hour erosion/corrosion screening tests of twelve candidate gas turbine vane and blade base alloys and a variety of protective coating systems have been completed. Test conditions included 1350/sup 0/F, 800 to 900 ft/s and particulate loadings of 30 to 90 ppM. Erosion/corrosion degradation rates of 1 to 4 mils/1000 hours were observed with corrosion predominant in areas of particle impaction. FeCrAlY, CoCrAlY and rhodium aluminide coatings show significantly better resistance to degradation than unprotected base alloys, aluminide or platinum-aluminide diffusion coatings.
Date: January 1, 1984
Creator: unknown
System: The UNT Digital Library
Photodegradation of mutagens in solvent-refined coal liquids (open access)

Photodegradation of mutagens in solvent-refined coal liquids

The purpose of this investigation was to evaluate any changes in the chemical composition and microbial mutagenicities of two representative solvent-refined coal (SRC) liquids as a function of exposure time to sunlight and air. This information was desired to assess potential health hazards arising from ground spills of these liquids during production, transport and use. Results of microbial mutagenicity assays using Salmonella typhimurium TA98, conducted after exposure, showed that the mutagenicities of both an SRC-II fuel oil blend and an SRC-I process solvent decreased continuously with exposure time to air and that the decrease was accelerated by simultaneous exposure to simulated sunlight. The liquids were exposed as thin layers supported on surfaces of glass, paper, clay or aluminum; but the type of support had little effect on the results. The contrast between these results and the reported increases of mutagenesis in organisms exposed simultaneously to coal liquids and near-ultraviolet light suggested that short-lived mutagenic intermediates, e.g., organic free radicals, were formed in the liquids during exposure to light. The highest activities of microbial mutagenicity in the SRC liquids were found in fractions rich in amino polycyclic aromatic hydrocarbons (amino PAH). After a 36-hour exposure of the fuel oil blend to …
Date: April 1, 1984
Creator: Kalkwarf, D. R.; Stewart, D. L.; Pelroy, R. A. & Weimer, W. C.
System: The UNT Digital Library
Effects of low-temperature fusion neutron irradiation on critical properties of a monofilament niobium-tin superconductor (open access)

Effects of low-temperature fusion neutron irradiation on critical properties of a monofilament niobium-tin superconductor

The objective of this work was to irradiate a Nb/sub 3/Sn superconductor with 14.8 MeV neutrons at 4 K and measure critical current in transverse fields of up to 12 T, irradiating up to a fluence sufficient to decrease the critical current to below its initial value. Critical temperatures were also to be measured. The samples were to be kept near 4 K between the irradiation and the measurement of critical properties. This work is directed toward establishing an engineering design fluence limit for Nb/sub 3/Sn when used in fusion reactor superconducting magnets.
Date: March 22, 1984
Creator: Guinan, M.W.; Van Konynenburg, R.A. & Mitchell, J.B.
System: The UNT Digital Library
Review of proposed EPA ambient lead criteria standard document. Final report. Task assignment No. 10 (open access)

Review of proposed EPA ambient lead criteria standard document. Final report. Task assignment No. 10

The proposed October 1983 EPA ambient lead criteria document, Air Quality Criteria for Lead is reviewed from the perspective of DOE's policies and programs and addresses potential impacts on energy production and energy-intensive industries. Following an introduction, the study is organized in five subsequent sections. Section 2.0 addresses environmental and health effects of exposure to lead. Section 3.0 reviews sources of lead emissions. Section 4.0 presents information on lead concentrations in ambient air. Section 5.0 examines dose-effect relationships among lead emissions, ambient air concentrations and blood lead levels. Section 6.0 presents Radian's evaluation of the regulatory implications of the criteria document and the information it provides. 10 figures, 11 tables.
Date: March 4, 1984
Creator: unknown
System: The UNT Digital Library