None

Alternative methods of connecting similar mutually coupled coils to their power supplies and dump resistors are investigated. The circuits are evaluated for both operating and fault conditions. The factors considered are the voltage to ground during a dump, short circuits, open circuits, quenches, and failure of the protection system to detect a quench. Of particular interest are the currents induced in coils that remain superconducting when one or more coils quench. The alternative connections include combined power supplies, individual dump resistors, combined resistors and series and parallel dump resistors. A new circuit that contains coupling resistors is proposed. The coupling resistors do not affect normal fast dumps but reduce the peak induced currents while also reducing the energy rating of the dump resistors. Another novel circuit, the series circuit with diodes, is discussed. The MFTF-B central-cell solenoids are used as an example.

Data and operating experience acquired during the last three years on the heat-transfer properties of pressurized superfluid He II indicate that the fluid can be successfully used as a coil coolant for high-field superconducting magnets. Indeed, the fluid seems to offer triple benefits over that of ordinary normal life: (1) coil conductors can be driven to wetted perimeter heat fluxes exceeding 1 W.cm/sup -2/; (2) the reduced low-temperature operation (from 4.2) at 1.8 K enhances the critical current densities (J/sub c/) of both Nb/sub 3/Sn and ternary additions to the compound by 140 to 200%; (3) the upper critical field (H/sub c2/) also increases, allowing viable solenoid magnet designs approaching 20-T peak fields. This paper reviews the significant properties of He II relevant to magnet design, describes current superconducting coils and systems that utilize the fluid, and discusses the possible application of the present data base to production of future ultrahigh-field superconducting coils yielding 20-T fields.

Desktop computers operating into a CAMAC-based interface are used to control and monitor the operation of the various subsystems on the Tandem Mirror Experiment-Upgrade (TMX-U) at Lawrence Livermore National Laboratory (LLNL). These systems include: shot sequencer/master timing, neutral beam control (four consoles), magnet power system control, ion-cyclotron resonant heating (ICRH) control, thermocouple monitoring, getter system control, gas fueling system control, and electron-cyclotron resonant heating (ECRH) monitoring. Two additional computers are used to control the TMX-U neutral beam test stand and provide computer-aided repair/test and development of CAMAC modules. These machines are usually programmed in BASIC, but some codes have been interpreted into assembly language to increase speed. Details of the computer interfaces and system complexity are described as well as the evolution of the systems to their present states.

A number of novel features of QCD are reviewed, including the consequences of formation zone and color transparency phenomena in hadronic collisions, the use of automatic scale setting for perturbative predictions, null-zone phenomena as a fundamental test of gauge theory, and the relationship of intrinsic heavy colored particle Fock state components to new particle production. We conclude with a review of the applications of QCD to nuclear multiquark systems. 74 references.

The Nova assurance management program was developed using the quality assurance (QA) approach first implemented at LLNL in early 1978. The LLNL QA program is described as an introduction to the Nova assurance management program. The Nova system is described pictorially through the Nova configuration, subsystems and major components, interjecting the QA techniques which are being pragmatically used to assure the successful completion of the project.

Photon-stimulated desorption experiments were performed on the (001) face of LiF for photon energies near the F(2s) and Li(ls) edges (from 37 to 72 eV). There are structures in the F{sup +} yield above the F(2s) edge which are absent in the Li{sup +} spectrum, differences in detail in the Li{sup +} and F{sup +} yields near the Li(1s) edge, and considerable broadening of the desorption yields as compared to the bulk photoabsorption spectrum. The first observation of a strong x-ray, and visible, beam exposure dependence of ion yields from LiF and NaF is also presented. These results are discussed in terms of electronic and defect properties of alkali halides.

The microstructural behavior of irradiated mixed-oxide fuel subjected to multiple, mild thermal transients was investigated using direct electrical heating. The results demonstrate that significant intergranular porosity, accompanied by large-scale (>90%) release of the retained fission gas, developed as a result of the cyclic heating. Microstructural examination of the fuel indicated that thermal-shock-induced cracking of the fuel contributed significantly to the increased swelling and gas release.

Extensive use of electron cyclotron resonant heating (ECRH) in the Tandem Mirror Experiment-Upgrade (TMX-U) requires continuous development of components to improve efficiency, increase reliability, and deliver power to new locations with respect to the plasma. We have used rectangular waveguide components on the experiment and have developed, tested, and installed circular waveguide components. We replaced the rectangular with the circular components because of the greater transmission efficiency and power-handling capability of the circular ones. Design, fabrication, and testing of all components are complete for all systems. In this paper we describe the design criteria for the system.

A review of corrosion and environmental effects on the mechanical properties of austenitic and ferritic steels for use with liquid metals in fusion reactors is presented. The mechanisms and kinetics of the corrosion processes in liquid lithium and Pb-17Li systems are examined and their influence on degradation of structural material is discussed. Requirements for additional data are identified.

Normal steam-side corrosion of steam-generator tubes in Liquid Metal Fast Breeder Reactors (LMFBRs) results in liberation of hydrogen, and most of this hydrogen diffuses through the tubes into the heat-transfer sodium and must be removed by the purification system. Cold traps are normally used to purify sodium, and they operate by cooling the sodium to temperatures near the melting point, where soluble impurities including hydrogen and oxygen precipitate as NaH and Na/sub 2/O, respectively. A computer model was developed to simulate the processes that occur in sodium cold traps. The Model for Analyzing Sodium Cold Traps (MASCOT) simulates any desired configuration of mesh arrangements and dimensions and calculates pressure drops and flow distributions, temperature profiles, impurity concentration profiles, and impurity mass distributions.

Using the SCEPTRE circuit modeling code, a computer model was developed for the MFTF Neutral Beam Power Supply System (NBPSS) Accel dc Power Supply (ADCPS). The ADCPS provides 90 kV, 88 A, to the Accel Modulator. Because of the complex behavior of the power supply, use of the computer model is necessary to adequately understand the power supply's behavior over a wide range of load conditions and faults. The model developed includes all the circuit components and parameters, and some of the stray values. The model has been well validated for transients with times on the order of milliseconds, and with one exception, for steady-state operation. When using a circuit modeling code for a system with a wide range of time constants, it can become impossible to obtain good solutions for all time ranges at once. The present model concentrates on the millisecond-range transients because the compensating capacitor bank tends to isolate the power supply from the load for faster transients. Attempts to include stray circuit elements with time constants in the microsecond and shorter range have had little success because of huge increases in computing time that result. The model has been successfully extended to include the accel modulator.

Studies have been performed during the past year to determine the configuration of a tandem mirror Fusion Power Demonstrator (FPD) machine capable of producing 1750 MW of fusion power. The FPD is seen as the next logical step after the Mirror Fusion Test Facility-B (MFTF-B) toward operation of a power reactor. The design of the FPD machine allows a phased construction: Phase I, a hydrogen or deuterium checkout machine; Phase 2, a DT breakeven machine; Phase 3, development of the Phase 2 machine to provide net power and act as a reactor demonstrator. These phases are essential to the development of remote handling equipment and the design of components that will ultimately be remotely handled. Phasing also permits more modes funding early in the program with some costs committed only after reaching major milestones.

We consider the requirements and constraints for negative-ion-based neutral beam injection systems, and show how these are reflected in design considerations. We will attempt to develop a set of guidelines for users and developers to use to see how well (in a qualitative sense, at least) a particular neutral beam system fits a particular proposed need.

A method was developed for economically fabricating short, wire-wound, steering magnets with maximum length, cosine-distributed, axial elements. This method utilizes multifunctional tooling to precisely flat-wind two-layer dipole halves that are subsequently reformed and encapsulated into semicylindrical form with confinement of the end turns into thin, half discs normal to the magnet axis. This paper addresses the magnet fabrication in detail, highlighting the inherent quality control features of the tooling, overall construction costs, and contemplated manufacturing enhancements.

Ion beam mixing in Pt-Si bilayered samples was measured during irradiation with projectiles ranging in mass from 4 amu (He) to 131 amu (Xe) at 10/sup 0/K, 300/sup 0/K and 373/sup 0/K. Using deposited damage energy as a basis for comparing the different irradiations, it was found that the heavier ions were more efficient than the lighter ones for inducing mixing. Moreover, it was observed that the mixing was essentially independent of temperature below 373/sup 0/K. These results are interpreted on the basis that the mixing is caused by the stimulated motion of defects during the cooling phase of energetic cascades.

The electron-cyclotron-resonant heating (ECRH) systems of rectangular waveguides on Tandem Mirror Experiment-Upgrade (TMX-U) operated with a overall efficiency of 50%, each system using a 28-GHz, 200-kW pulsed gyrotron. We designed and built four circular-waveguide systems with greater efficiency and greater power-handling capabilities to replace the rectangular waveguides. Two of these circular systems, at the 5-kG second-harmonic heating locations, have a total transmission efficiency of >90%. The two systems at the 10-kG fundamental heating locations have a total transmission efficiency of 80%. The difference in efficiency is due to the additional components required to launch the microwaves in the desired orientation and polarization with respect to magnetic-field lines at the 10-kG points. These systems handle the total power available from each gyrotron but do not have the arcing limitation problem of the rectangular waveguide. Each system requires several complex components. The overall physical layout and the design considerations for the rectangular and circular waveguide components are described here.

Applying programmable controllers in critical applications such as personnel safety and interlocks systems requires special considerations in the design of both hardware and software. All modern programmable controller systems feature extensive internal diagnostic capabilities to protect against problems such as program memory errors; however most, if not all present designs lack an intrinsic capability for detecting and countering failures on the field-side of their I/O modules. Many of the most common styles of I/O modules can also introduce potentially dangerous sneak circuits, even without component failure. This paper presents the most significant lessons learned to date in the design of the MFTF-B Personnel Safety and Interlocks System, which utilizes two non-redundant programmable controllers with over 800 I/O points each. Specific problems recognized during the design process as well as those discovered during initial testing and operation are discussed along with their specific solutions in hardware and software.

The optimum plasma for the tandem Mirror Fusion Test Facility (MFTF-B) at Lawrence Livermore National Laboratory (LLNL) is very sensitive to heavy contaminates, such as oxygen and metals. Unfortunately the current neutral beam sources generate not only high energy deuterium particles but also high energy oxygen particles. A new MFTF-B separator/neutralizer has been designed to filter out the unwanted oxygen and allow only primary species neutrals to reach the plasma.

The Electromagnetic Fluctuations (EMF) diagnostic will be used to monitor ion fluctuations which could be unstable in MFTF-B. Each probe assembly includes a high impedance electrostatic probe to measure potential fluctuations, and a group of nested, single turn loops to measure magnetic fluctuations in three directions. Eventually, more probes and loops will be added to each probe assembly for making more detailed measurements. The sensors must lie physically close to the plasma edge and are radially positionable. Also, probes at separate axial locations can be positioned to connect along the same magnetic field line. These probes are similar in concept to the rf probes used on TMX, but the high thermal load for 30-second shots on MFTF-B requires a water-cooled design along with temperature monitors. Each signal channel has a bandwidth of .001 to 150 MHz and is monitored by up to four different data channels which obtain amplitude and frequency information. This paper describes the EMF diagnostic and presents the detailed mechanical and electrical designs.

The Plasma Current Sensor (PCS) diagnostic includes large diamagnetic loops (DL) that fully encircle the plasma as well as small multi-turn pickup coils (PCs) located between the plasma and the superconducting magnets. Both types of sensors respond to changing magnetic flux linkages caused by plasma currents and are used to measure plasma diamagnetism, from which estimates of temperature and density can be made. The DLs are used in the central cell and Axicell regions, while the PCs are used in the Yin-yang regions where DLs are impractical. Other PCs are used in the central cell to detect axial plasma currents, to help tune trim coils in the transition cell and confirm theoretical estimates of radial diffusion limits. This paper describes the PCS diagnostic and presents the detailed mechanical and electrical designs.

The orientation dependence of characteristic x-ray emissions have been used to determine specific site occupations of Rare Earth additions in epitaxially grown films of Y/sub 1/ /sub 7/Sm/sub 0/ /sub 6/Lu/sub 0/ /sub 7/Fe/sub 5/O/sub 12/. A theoretical formulation based on the assumption of highly localized inner shell excitations was used not only to predict specific site sensitive orientations, but also to refine experimentally observed data employing a constrained least squares analysis to give probabilities for the occupation of the RE additions in the different crystallographic sites. Thus, it has been shown that in this compound the preference for the RE additions is a predominantly octahedral occupation with a probability greater than or equal to 95%. Some of the assumptions and limitations of the technique have also been discussed.

The diagnostic systems for Tandem Mirror Experiment-Upgrade (TMX-U) have grown from eleven initial systems to more than twenty systems. During operation, diagnostic system modifications are sometimes required to complete experimental objectives. Also, during operations new diagnostic systems are being developed and implemented. To ensure and maintain the quality and integrity of the data signals, a set of plans and systematic actions are being developed. This paper reviews the procedures set in place to maintain the integrity of existing data systems and ensure the performance objectives of new diagnostics being added.

Simulated SRL waste was prepared with compositions varying in iron and aluminum content. Two batches with similar composition were produced with different amounts of reducing agent added. Samples were isothermally heat treated and used to derive time-temperature-transformation diagrams. Supplementary samples were cooled in a manner programmed to simulate the cooling curves of production canisters. Less than 10% total devitrification occurs during normal processing. However, when waste glass 165 was purposely devitrified, up to 30 volume percent total spinel and acmite formed. Formation of these species had minor effect on leachability in MCC-1 and accelerated leach tests. 20 references, 4 figures, 2 tables.