A steering system for use with a multiple vehicle train is disclosed which permits tracking without rails of one vehicle after another. This system is particularly useful for moving conveyor systems into and out of curved paths of room and pillar underground mine installations. The steering system features an elongated steering bar pivotally connected to each of adjacent vehicles at end portions of the bar permitting angular orientation of each vehicle in respect to the steering bar and other vehicles. Each end portion of the steering bar is linked to the near pair of vehicle wheels through wheel yoke pivot arms about king pin type pivots. Movement of the steering bar about its pivotal connection provides proportional turning of the wheels to effect steering and tracking of one vehicle following another in both forward and reverse directions.

A neutral beamline employing direct energy recovery of unneutralized residual ions is provided which enhances the energy recovery of the full energy ion component of the beam exiting the neutralizer cell, and thus improves the overall neutral beamline efficiency. The unneutralized full energy ions exiting the neutralizer are deflected from the beam path and the electrons in the cell are blocked by a magnetic field applied transverse to the beam direction in the neutralizer exit region. The ions which are generated at essentially ground potential and accelerated through the neutralizer cell by a negative acceleration voltage are collected at ground potential. A neutralizer cell exit end region is provided which allows the magnetic and electric fields acting on the exiting ions to be loosely coupled.

A surge counter for a rotating compressor is provided which detects surging by monitoring the vibration signal from an accelerometer mounted on the shaft bearing of the compressor. The circuit detects a rapid increase in the amplitude envelope of the vibration signal, e.g., 4 dB or greater in less than one second, which is associated with a surge onset and increments a counter. The circuit is rendered nonresponsive for a period of about 5 seconds following the detection which corresponds to the duration of the surge condition. This prevents multiple registration of counts during the surge period due to rapid swings in vibration amplitude during the period.

A secondary concentrator for use in receiver systems for linear focusing primary concentrators is provided with reflector wings at each end. The wings increase the capture of light rays reflected from areas adjacent the rim of a primary concentrator, increasing the apparent aperture size of the receiver as viewed from the rim of the primary concentrator. The length, tilt, and curvature of the wing reflectors can be adjusted to provide a receiver having a desired aperture aspect.

A US Air Force (USAF) Residential Energy Conservation Methodology was developed to compare USAF needs and available data to the procedures of the Residential Conservation Service (RCS) program as developed for general use by utility companies serving civilian customers. Attention was given to the data implications related to group housing, climatic data requirements, life-cycle cost analysis, energy saving modifications beyond those covered by RCS, and methods for utilizing existing energy consumption data in approaching the USAF survey program. Detailed information and summaries are given on the five subtasks of the program. Energy conservation alternatives are listed and the basic analysis techniques to be used in evaluating their thermal performane are described. (MCW)

The assay of nuclear material holdup in fuel manufacturing plants is a laborious but often necessary part of completing the material balance. A range of instruments, standards, and a methodology for assaying holdup has been developed. The objectives of holdup measurement are ascertaining the amount, distribution, and how firmly fixed the SNM is. The purposes are reconciliation of material unbalance during or after a manufacturing campaign or plant decommissioning, to decide security requirements, or whether further recovery efforts are justified.

The primary barrier to release of fission product from any of the fuel types into the primary circuit of the HTGR are the coatings on the fuel particles. Both pyrolytic carbon and silicon carbide coatings are very effective in retaining fission gases under normal operating conditions. One of the possible performance limitations which has been observed in irradiation tests of TRISO fuel is chemical interaction of the SiC layer with fission products. This reaction reduces the thickness of the SiC layer in TRISO particles and can lead to release of fission products from the particles if the SiC layer is completely penetrated. The experimental section of this report describes the results of work at General Atomic concerning the reaction of fission products with silicon carbide. The discussion section describes data obtained by various laboratories and includes (1) a description of the fission products which have been found to react with SiC; (2) a description of the kinetics of silicon carbide thinning caused by fission product reaction during out-of-pile thermal gradient heating and the application of these kinetics to in-pile irradiation; and (3) a comparison of silicon carbide thinning in LEU and HEU fuels.

A system is provided for utilizing fines of carbonaceous materials such as particles or pieces of oil shale of about one-half inch or less diameter which are rejected for use in some conventional or prior surface retorting process, which obtains maximum utilization of the energy content of the fines and which produces a waste which is relatively inert and of a size to facilitate disposal. The system includes a cyclone retort which pyrolyzes the fines in the presence of heated gaseous combustion products, the cyclone retort having a first outlet through which vapors can exit that can be cooled to provide oil, and having a second outlet through which spent shale fines are removed. A burner connected to the spent shale outlet of the cyclone retort, burns the spent shale with air, to provide hot combustion products that are carried back to the cyclone retort to supply gaseous combustion products utilized therein. The burner heats the spent shale to a temperature which forms a molten slag, and the molten slag is removed from the burner into a quencher that suddenly cools the molten slag to form granules that are relatively inert and of a size that is convenient to handle …

The usefulness of sister chromatid exchange (SCE) induction as a measure of low-level radiation effect was examined in a benthic marine worm, Neanthes arenaceodentata. Larvae were exposed to /sup 60/Co radiation for 12 to 24 h at total doses ranging from 0.5 to 309 R and at dose rates from 0.04 to 13 R/h. Animals exposed at intermediate dose rates (0.5, 0.6, 1.25, 2.0, and 2.5 R/h) had SCE frequencies per chromosome about twice that of those receiving no radiation (controls), whereas those exposed at the higher dose rates (7.0 and 13 R/h) had SCE frequencies lower than the controls. Animals exposed at the lower dose rates (0.04 and 0.1 R/h) had lower SCE frequencies than those exposed at intermediate dose rates (and higher SCE frequencies than controls). The length of chromosome pair number one differed among metaphase spreads and was used as an index of chromosome condensation in a given metaphase. Because there is a possibility that chromosome morphology may affect the ability to resolve SCEs, morphology will be monitored in future studies. A preliminary experiment was performed to assess the effects of 2.2 and 11.5 R/h for 24 h on growth and development. Larvae observed at 6 and …

A proposal of using extrapolation algorithms as an analytical - numerical tool for the evaluation of the beam-beam effects in storage rings is formulated. These algorithms already known to experts of Applied Mathematics are described in some detail. Physical models for the beam-beam interaction effects on betatron motion and polarization of a test particle are discussed and put in such a form to allow the application of the extrapolation algorithms.

Copper plates 90 mm in diameter, of thickness 0.25 mm and 0.5 mm, were accelerated by an adjacent 17 mm thick cylinder of RX-03-BB or PBX-9404-03. The explosive was initiated by impact of a thick flyer from the LLNL 102 mm gun, providing either a reactive or fully detonating wave, by appropriate choice of flyer velocities up to 1.30 mm/..mu..s. The free surface velocity of the plates were measured with a Fabry-Perot velocimeter. Excellent experimental free-surface velocity histories have been obtained. Calculations of this history employing beta-burn and nucleation and growth high explosives models are in good agreement with fully detonating experiments. For reacting RX-03-BB, adjustments in the parameter are needed. The experimental technique gives records whose agreement with calculation is sensitive to the model and is therefore a good way of testing new high explosive models. Also, this method allows one to infer information about the reaction zone length.

Experimental results in TMX have confirmed the basic principles of the tandem-mirror concept. A center-cell particle confinement parameter eta tau approx. 10/sup 11/ cm/sup -3/ s has been obtained at ion temperatures around 100 eV, which is a hundred-fold improvement over single mirrors at the same temperatures. For TMX these results have been obtained at peak beta values in the center cell in the range 10 to 40%, not yet limited by MHD activity; and ion-cyclotron resonant heating (ICRH) in the Phaedrus tandem-mirror experiment has produced beta values approx. 25%, which is several times the ideal MHD limit for that device. In addition, it has been demonstrated that the end fan chambers of TMX simultaneously isolate the hot electrons from the end walls, provide adequate pumping and conveniently dispose of the exhaust plasma energy either by thermal deposition on the end wall or by direct conversion to electricity (at 48% efficiency in agreement with calculations). Also, evidence was obtained for inherent divertor action in TMX, presumably in part responsible for the observed low impurity level (<0.5% low-Z ions in the center cell).

The potential environmental and socioeconomic impacts of the production of energy contained in hot dry rock (HDR) is surveyed here. In general, careful siting and timing and routine control measures should be adequate to prevent significant environmental harm; sites of particular ecological or visual and recreational value, however, may require more extensive (and more expensive) precautions such as using multiwell pads to reduce land disturbance and dry or wet and dry cooling towers to reduce or eliminate the consumptive use of water. The most important uncertainty among the environmental concerns is the seismic response of HDR formations to short-duration fluid injections at pressures above fracture thresholds; continued monitoring at HDR development sites is necessary. The direct socioeconomic impacts of HDR development should be relatively minor, owing to its capital-intensive nature. Of greater potential importance are the indirect jobs resulting from such development, which could cause significant demographic (and thus fiscal and social) impacts in sparsely populated regions. However, such indirect growth is not expected to begin until a large, stable HDR industry is established in a region, and thus its impacts are expected to be permanent rather than transient.

This system provides trigger signals at various times and clock signals at various frequencies for the CAMAC transient recorders of the plasma diagnostics system for the TMX-Upgrade. The timing system is designed so that all clocks are in fixed-phase relation to their corresponding triggers and to each other. Therefore, data recorded from the different diagnostics can be directly time compared. Trigger signals can be generated in 100-ns increments, with an uncertainty of 500 ps. The clock signals have a time uncertainty of less than 1 ns. The system is arranged so that these accuracies are maintained over the entire diagnostic room. The timing system is modular and uses mostly digital delay generators, signal fan outs, and frequency dividers. Because of the modular approach, the system can be arranged in several ways (producing many possible trigger times and sample rate clocks) and still maintain a system in which all clocks and triggers are in a fixed-phase relationship.

The high temperature diffusion technique for fuel filling of some future direct drive cryogenic ICF targets may be unacceptable. The following describes a technique of fitting a 1 mm diameter x 6 ..mu..m thick glass microsphere with an approx. 50 ..mu..m O.D. glass fill tube. The process of laser drilling a 50 ..mu..m diameter hole in the microsphere wall, technique for making the epoxy joint between the sphere and fill tube, as well as the assembly procedure are also discussed.

A combination regenerative ring and backward Raman waveguide amplifier and a combination regenerative ring oscillator and backward Raman waveguide amplifier which produce Raman amplification, pulse compression, and efficient energy extraction from the CO/sub 2/ laser pump signal for conversion into a Stokes radiation signal. The ring cavity configuration allows the CO/sub 2/ laser pump signal and Stokes signal to copropagate through the Raman waveguide amplifier. The backward Raman waveguide amplifier configuration extracts a major portion of the remaining energy from the CO/sub 2/ laser pump signal for conversion to Stokes radiation.

Results are presented for leach testing at 95/sup 0/C and 200/sup 0/C of SYNROC containing 9% and 20% simulated high level radioactive waste, synthetic hollandite and pervoskite samples, and natural zirconolite and pervoskite samples. Single phase synthetic minerals show much higher leach rates than natural mineral samples and polyphase SYNROC samples. Natural zirconolite samples with low radiation damage have leach rates at 200/sup 0/C based on U which are identical to those measured on SYNROC samples. Natural zirconolites with very large accumulated ..cap alpha.. dose and radiation damage have leach rates at 200/sup 0/C which are only 5 times higher than those of low dose samples.

The National Seismic Stations (NSS) instruments are being developed for seismic monitoring of regional and teleseismic events. They consist of two 3-component, broadband, borehole seismometers: the KS-36000 and the S-700, which is the backup for the KS-36000. Output is divided into frequency bands to reduce data loss due to saturation. Complete block diagrams of the KS-36000 and S-700 NSS seismometers and filters are presented. Both open-loop and closed-loop steady-state amplitude and phase curves are given. Without band-pass filters (but with shaping filters) the KS-36000 has a flat (i.e., between the -3dB points) velocity sensitivity from 0.03 to 23 Hz. With its shaping filters, the S-700 is flat from 0.2 to 40 Hz. The structure of the three band-pass filters (LP, MP, and SP) is superimposed on these velocity sensitivities. Passbands of the resulting overall velocity sensitivity for the KS-36000 are as follows: LP band = 0.01-0.05 Hz, MP band = 0.02-1.3 Hz, and SP band = 1-10 Hz. Step-function responses and phase and group delays are given for each of the bands. The MP-band step response is oscillatory due to its sharp, high-frequency cutoff, but an MP-band filter with a less abrupt cutoff eliminates the oscillation. To generate typical NSS …

Components of the dye-penetrant-testing process were characterized by microanalytical methods. Particulate material of a size range, which was small enough to plug the small leaks in thin-walled cans, was found. Testing of simulated leaks before and after dye-penetrant examination showed that the dye-penetrant testing had a high probability of plugging leaks < 1 x 10/sup -4/ atm-cm/sup 3//s of helium in size.

The DOE Conservation Program for Consumer Products requires the testing of products to determine whether they meet applicable energy-efficiency standards. Certification testing will take place at the manufacturers' facilities, while monitoring and enforcement usually take place at or by an independent test laboratory (ITL). Specifically, monitoring will take place at ITLs except in the case of trade-association programs where testing is generally conducted by trade-association representatives. ITLs will be utilized by DOE for all enforcement testing. Monitoring- and enforcement-test requirements are provided in Sections 2 and 3. Estimates and associated analysis of existing ITL capacity are given in Section 4. Section 5 compares ITL capacity and projected test-facility requirements and examines the cost and difficulty of eliminating projected deficits. A summary and conclusions are presented in Section 6. Appendix A presents an analysis of the sensitivity of projected ITL requirements to changes in key variables.

Conceptual design studies of a cusp field rf ion source are described. A diagram of the thruster is given. (MOW)

A weekly publication, the Texas Register serves as the journal of state agency rulemaking for Texas. Information published in the Texas Register includes proposed, adopted, withdrawn and emergency rule actions, notices of state agency review of agency rules, governor's appointments, attorney general opinions, and miscellaneous documents such as requests for proposals. After adoption, these rulemaking actions are codified into the Texas Administrative Code.

A weekly publication, the Texas Register serves as the journal of state agency rulemaking for Texas. Information published in the Texas Register includes proposed, adopted, withdrawn and emergency rule actions, notices of state agency review of agency rules, governor's appointments, attorney general opinions, and miscellaneous documents such as requests for proposals. After adoption, these rulemaking actions are codified into the Texas Administrative Code.

A weekly publication, the Texas Register serves as the journal of state agency rulemaking for Texas. Information published in the Texas Register includes proposed, adopted, withdrawn and emergency rule actions, notices of state agency review of agency rules, governor's appointments, attorney general opinions, and miscellaneous documents such as requests for proposals. After adoption, these rulemaking actions are codified into the Texas Administrative Code.