The viewgraphs from a talk on measurement of performance of applications programs are given. The area of interest is hydrodynamics. Only the viewgraphs are included; there is no text. (RWR)

Fuel cells show great promise as an efficient, nonpolluting vehicular power source that can operate on nonpetroleum fuel. As with other power sources, design tradeoffs can be made that either improve vehicle performance or reduce the size and cost of the fuel cell power system. To evaluate some of these tradeoffs, a number of phosphoric acid fuel cell power plant designs have been studied to determine the performance level they would provide, both for a compact passenger vehicle and a 40-ft city bus. The fuel is steam reformed methanol. The analyses indicate that 1978 fuel cell technology can provide a 22 to 50% improvement in fuel economy over the 1980 EPA estimate for the conventionally powered General Motors X car. With this technology the city bus can meet the DOT acceleration, gradability, and top speed requirements. A reasonable advance in fuel cell technology improves performance and fuel consumption of both vehicles substantially.

The tasks, objectives and completed work are discussed for the legislative and institutional program, cities program, geothermal applications utilization technology, and outreach. The work on the Maryvale Terrace development and the New Mexico Energy Institute are described. (MHR)

Three areas are reported: geothermal administration, geothermal planning, and other geothermal activities. Administration covers the status of the Imperial Valley Environmental Project transfer, update of the Geothermal Resource Center, and findings of the geothermal field inspections. Planning addresses Board of Supervisor actions, Planning Commission actions, notice of exemptions, and the master Environmental Impact Report for Salton Sea. The other activity includes the County Direct Heat Development study; the solicitation for district heating and cooling proposals; the new Geothermal Class II-1 disposal site; the DOE Region IX meeting in Tucson; and USGA designating a new KGRA, the East Brawley KGRA, the Westmoreland KGRA, and revising the southern border of the Salton Sea KGRA. (MHR)

Extensive NMR measurements of the proton relaxation times have been performed on low (i.e., alpha-phase) and intermediate (i.e., alpha'-phase) hydrogen concentrations in TiCr{sub}2H{sub}x with both the hexagonal Cl4 and cubic Cl5 Laves structures. The relaxation times indicate rapid diffusion rates above 200 K for all the TiCr{sub}2H{sub}x phases; however, large differences in the diffusion activation energies are observed. This behavior is associated with the hydrogen interstitial site occupancies and diffusion pathways becoming restricted in the Cl4 structure.

The overall objective of this program is to determine the optical properties of i-Carbon (diamond-like) films and determine if these films can be developed into antireflecting (AR) coatings for silicon solar cells. The i-C films have been produced on glass, silicon, and KCl by radio frequency (RF) plasma decomposition of the alkane gases. Films were also produced on silicon solar cells by low-energy ion beam techniques. These coatings did not perform as well as those made from hydrocarbon gases. Significant progress has been made in understanding the deposition parameters that affect the optical properties of the films. The optical constants n and k have been determined over a large range of process parameters and source gas. The degree of hydrogen incorporation in these films has been studied by SIMS analysis. It was found that the lower optically absorbing films contain more hydrogen. This hydrogen does not, however, manifest itself in fundamental C-H absorption bands in the infrared. Very efficient single-layer quarter-wave i-C AR coatings have been produced on single-crystal and SOC Si solar cells. An increase in cell efficiency of 40% over uncoated cells has been achieved.

Investigations of ion generation and recombination mechanisms in the cesium plasma as they pertain to the advanced mode thermionic energy converter are described. The changes in plasma density and temperature within the converter have been studied under the influence of several promising auxiliary ionization candidate sources. Three novel approaches of external cesium ion generation have been investigated in some detail, namely vibrationally excited N/sub 2/ as an energy source of ionization of Cs ions in a DC discharge, microwave power as a means of resonant sustenance of the cesium plasma, and ion generation in a pulse N/sub 2/-Cs mixture. The experimental data obtained and discussed show that all three techniques - i.e. the non-LTE high-voltage pulsing, the energy transfer from vibrationally excited diatomic gases, and the external pumping with a microwave power - have considerable promise as schemes in auxiliary ion generation applicable to the advanced thermionic energy converter.

This analysis of advanced wastewater treatment systems for coal gasification plants highlights the three coal gasification demonstration plants proposed by the US Department of Energy: The Memphis Light, Gas and Water Division Industrial Fuel Gas Demonstration Plant, the Illinois Coal Gasification Group Pipeline Gas Demonstration Plant, and the CONOCO Pipeline Gas Demonstration Plant. Technical risks exist for coal gasification wastewater treatment systems, in general, and for the three DOE demonstration plants (as designed), in particular, because of key data gaps. The quantities and compositions of coal gasification wastewaters are not well known; the treatability of coal gasification wastewaters by various technologies has not been adequately studied; the dynamic interactions of sequential wastewater treatment processes and upstream wastewater sources has not been tested at demonstration scale. This report identifies key data gaps and recommends that demonstration-size and commercial-size plants be used for coal gasification wastewater treatment data base development. While certain advanced treatment technologies can benefit from additional bench-scale studies, bench-scale and pilot plant scale operations are not representative of commercial-size facility operation. It is recommended that coal gasification demonstration plants, and other commercial-size facilities that generate similar wastewaters, be used to test advanced wastewater treatment technologies during operation by using …

The solenoid design follows closely the considerations qiven in {bar p} note 116. In particular we try to make the solenoid undivided, but with a centre tap for the cooling water. We found a variant for the centre tap, so that the two layers are now electrically in series. Due to the very long length, it seems better not to fill the clearance between return yoke and OD of the second layer with epoxy. Instead, we support and adjust the coil every 2 m with three bolts at 120 deqrees screwed in the return yoke. The latter is then supposed to be sufficiently stiff, so as to give the weaker mandrel the desired straightness. We give a positive pitch, i.e. somewhat more than the width of the copper section including insulation and tolerances. The precise pitch cannot be stated here, because the copper section will be somewhat trapezoidal. How much, depends on the winding procedure. The layers are epoxy impregnated and solidair with the mandrel. The Figures show an axial section and the construction of the central water tap. The dimensions shown are on the assumption of a free choice of the diameters of return yoke and mandrel. This may …

The A.P.T. Dry Plate Scrubber (DPS) uses a shallow, dense mobile bed of solid collector granules which move across a perforated plate. The gas stream containing fine particles and vapors is moved upward through the perforations to form high velocity gas jets. The fine particles are removed by inertial deposition onto the collector granules or by direct interception. Electrostatic forces also can be used to improve the collection efficiency and increase the adhesive forces between the particles and collectors. The DPS column consists of a series of collection stages (perforated plates) with the collectors either passing sequentially over each stage or being fed separately to each stage. The stages can be designed so as to promote the collection of large particles on the lower stages and the collection of fine particles and alkali vapors on the upper stages. The DPS is especially well suited for cleaning high temperature and pressure gases such as the effluent from a pressurized fluidized bed combustion (PFBC) process. The objective of this project is to conduct a bench scale experimental evaluation of the DPS at high temperature and pressure to determine its potential for controlling particulate and alkali vapor emissions from PFBC processes.

In the last year the following experiments have been carried out: (A) magneto-oscillations have been observed in the dislocation drag process, (B) a rotational peak has been observed; this peak is related to the rotation of a magnetic field relative to the slip plane of deforming crystal, (C) twinning of a zinc crystal was shown to be related to the velocity of the dislocations involved. This correspondence between the nucleation of dislocation twinning and dislocation velocity has not been observed before.

The generalized conjugate gradient scheme based on the k-line block Jacobi splitting A = M-N was studied for solving model two-dimensional parabolic and elliptic difference equations AU = F tilde. A represents the matrix ch/sup ..cap alpha../-h/sup 2/..delta../sub h/. Eigenvalues of M/sup -1/N cluster, and the cluster radii decrease as ch/sup ..cap alpha../ or k increases. Computations with k = 4, 8, 16, 32, and ch/sup ..cap alpha../ = 0, h, 2 are discussed.

The effort reported is a continuation of the development testing of the 1.5-ton solar desiccant air conditioner (SODAC) and is concerned with determination of the SODAC performance in the recirculated and ventilated mode configuration. Test data in the recirculated mode are presented. As originally conceived, the SODAC features two-speed indoor and outdoor fans to permit more efficient operation at reduced capacity. In both full-flow and half-flow cases, the experimental data are compared to computer predictions. The system and its operation are described, as are the system test facility and procedures. The system description includes the characteristics of the major components, the performance at design conditions, and the control schemes for optimum operation in various climates. (LEW)

Measurements have been made of thermal conductivity, diffusivity, and linear expansion as a function of temperature (to 573 K) and hydrostatic pressure (to 50 MPa) on two rocks, Avery Island domal salt and Climax Stock quartz monzonite. For Avery Island salt the thermal properties do not show any pressure dependence and are approximately the same values as for single crystal halite at 0.1 MPa. The lack of pressure dependence is attributed to the high symmetry of halite (cubic) and to its low strength, both of which inhibit brittle fracturing. For Climax Stock quartz monzonite no pressure dependence of thermal diffusivity has been resolved, but conductivity does show a drop of approximately 10% with decreasing pressure from 50 to 3 MPa. The pressure dependence is not measurably altered by heating the rock to as high as 473 K under 50 MPa. Our measurements so far on the thermal conductivity of quartz monzonite vs temperature and pressure are in agreement with predictions of the Walsh and Decker (1966) model of thermal conductivity vs crack porosity based on independent measurements of crack porosity vs temperature and pressure for the same quartz monzonite. Heating to temperatures greater than 473 K at 50 MPa, or …

An assessment is made of the technical and economical feasibility of converting municipal waste into useful and useable energy. The concept presented involves retrofitting an existing municipal incinerator with the systems and equipment necessary to produce process steam and electric power. The concept is economically attractive since the cost of necessary waste heat recovery equipment is usually a comparatively small percentage of the cost of the original incinerator installation. Technical data obtained from presently operating incinerators designed specifically for generating energy, documents the technical feasibility and stipulates certain design constraints. The investigation includes a cost summary; description of process and facilities; conceptual design; economic analysis; derivation of costs; itemized estimated costs; design and construction schedule; and some drawings.

The use of empirical pseudopotentials, in evaluating interatomic potentials, provides an inexpensive and convenient method for obtaining highly accurate potential curves and permits the modeling of core-valence correlation, and the inclusion of relativistic effects when these are significant. As an example, recent calculations of the chi/sup 1/..sigma../sup +/ and a/sup 3/..sigma../sup +/ states of LiH, NaH, KH, RbH, and CsH and the chi/sup 2/..sigma../sup +/ states of their anions are discussed. Pseudopotentials, including core polarization terms, have been used to replace the core electrons, and this has been coupled with the development of compact, highly-optimized basis sets for the corresponding one- and two-electron atoms. Comparisons of the neutral potential curves with experiment and other ab initio calculations show good agreement (within 1000 cm/sup -1/ over most of the potential curves) with the difference curves being considerably more accurate.

The structure of coal and the processes of coal gasification and coal liquefaction are reviewed. While coal conversion technology is not likely to provide a significant amount of synthetic fuel within the next several years, there is a clear interest both in government and private sectors in the development of this technology to hedge against ever-diminishing petroleum supplies, especially from foreign sources. It is evident from this rather cursory survey that there is some old technology that is highly reliable; new technology is being developed but is not ready for commercialization at the present state of development. The area of coal conversion is ripe for exploration both on the applied and basic research levels. A great deal more must be understood about the reactions of coal, the reactions of coal products, and the physics and chemistry involved in the various stages of coal conversion processes in order to make this technology economically viable.

Chemical decomposition models have been deduced from the available chemical kinetic data on the thermal decomposition of HMX, TATB, RDX, and TNT. A thermal conduction model is used in which the thermal conductivity of the reacting explosive decreases linearly with the mass fraction reacted to that of the gaseous products. These reactive heat flow models are used to predict the time to explosion versus reciprocal temperature curves from several heavily confined explosive tests. Good agreement is obtained between experimental and calculated explosion times for the pure explosives HMX, TATB, RDX, and TNT, mixtures such as RX-26-AF (HMX/TATB), Octol (HMX/TNT), and Comp B (RDX/TNT), and for PBX 9404, an HMX-based explosive containing an energetic nitrocellulose binder.

A hydrotreating catalyst is prepared from coal mineral matter obtained by low temperature ashing coals of relatively low bassanite content by the steps of: (a) depositing on the low temperature ash 0.25 to 3 grams of an iron or nickel salt in water per gram of ash and drying a resulting slurry; (b) crushing and sizing a resulting solid; and (c) heating the thus-sized solid powder in hydrogen.

A minimally refined fluid composition, suitable as a fuel mixture and derived from biomass material, is comprised of one or more water-soluble carbohydrates such as sucrose, one or more alcohols having less than four carbons, and water. The carbohydrate provides the fuel source; water-solubilizes the carbohydrate; and the alcohol aids in the combustion of the carbohydrate and reduces the viscosity of the carbohydrate/water solution. Because less energy is required to obtain the carbohydrate from the raw biomass than alcohol, an overall energy savings is realized compared to fuels employing alcohol as the primary fuel.

Information on heterogeneous assembly evaluation is presented concerning ringed moderator description and flux trap description; cross section generation; ringed moderator results; effects of heterogeneous moderation; sodium void worth breakdown; flux trap configuration; flux trap results; the effects of stoichiometric variation in the moderator; and the effects of lattice representation. Also discussed is the engineering compatibility of heterogeneous assembly designs.

A wood container for shipping and storing radioactive waste was designed to eliminate the problems caused by the weight, cost, and shape of the steel containers previously used. Tests specified by federal regulations (compression, free-drop, penetration, and vibration) were conducted on two of the containers, one loaded to 2500 lb and one loaded to 5000 lb. The 5000-lb container failed the free-drop test, but the 2500-lb container easily passed the tests and therefore qualifies as a Type A container. Its simplicity of design, low weight, and ease in handling have proved to be time-saving and cost-effective.

Flexibility in MFTB-B will be achieved partly by using the margins in particle and energy control designed into the machine and partly by making modest changes based on results obtained in TMX Upgrade. This latter flexibility is permitted by the schedule for vessel construction and component fabrication. The changes we might expect were determined by an examination of the processes involved in creating a thermal barrier and by speculating on the range of outcomes from TMX Upgrade experiments.

A computer simulation code at the Lawrence Livermore National Laboratory (LLNL) to predict the performance of a railgun electromagnetic accelerator has been developed and validated. The code, called MAGRAC (MAGnetic Railgun ACcelerator), models the performance of a railgun driven by a magnetic flux compression current generator (MFCG). The MAGRAC code employs a time-step solution of the nonlinear time-varying element railgun circuit to determine rail currents. From the rail currents, the projectile acceleration, velocity, and position are found. The MAGRAC code was validated through a series of eight railgun tests conducted jointly with the Los Alamos National Laboratory. The formulation of the MAGRAC railgun model is described and the predicted current waveforms compared with those obtained from full-scale experiments.