The absolute cross sections for the single, double, triple and quadruple ionization of Cs/sup +/ ions by electron impact have been measured from below their respective thresholds to approximately 5000 eV. This determination has been accomplshed using a crossed beam facility in which monoenergetic beams of ions and electrons are caused to intersect at right angles in a well-defined collision volume. Multiply charged, product ions born as a result of the electron impact are deflected into their respective detectors by cascaded electrostatic analyzers. The multiply charged beam current component is measured by means of a vibrating reed electrometer operating in the rate-of-charge mode.

During the past three months effort has concentrated on formulating a method to predict the enhancement of electrode surface field and power input occasioned by the presence of a projection on the electrode surface, during the ion sheath development period which attends the scavenging a contact gap following current interruption in vacuum. In addition, experimental evidence has been obtained to support the theory, postulated earlier, of a turn-around interval for electrons left in the gap, which preceeds the rise of the transient recovery voltage.

Extensive data analysis and theoretical analysis has been done to complete the extensive decay scheme investigation of /sup 206/ /sup 208/Fr and the level structures of /sup 206/ /sup 208/Rn. A final version of a journal article is presented in preprint form. Extensive Monte Carlo calculations have been made to correct the end point energies of positron spectra taken with intrinsic Ge detectors for annihilation radiation interferences. These calculations were tested using the decay of /sup 82/Sr which has previously measured positron branches. This technique was applied to the positron spectra collected at the on-line UNISOR isotope separator. The reactions used were /sup 60/Ni(/sup 20/Ne;p2n)/sup 77/Rb and /sup 60/Ni(/sup 20/Ne;pn)/sup 78/Rb. Values for 5, ..gamma..-..beta../sup +/ coincidence positron end point energies are given for the decay of /sup 77/Rb. The implied Q-value is 5.075 +- 0.010 MeV. A complete paper on the calculated corrections is presented. A flow chart of a more complete program which accounts for positrons scattering out of the detector and for bremsstralung radiation is also presented. End-point energies of four ..beta../sup +/ branches in /sup 77/Rb are given as well as a proposed energy level scheme of /sup 75/Kr based on ..gamma..-..gamma.. coincidence data taken at …

A method has been developed for the determination of plutonium in air samples and smear samples that were collected on filter papers. The sample papers are digested in nitric acid, extracted into 2-thenoyltrifluoroacetone (TTA)-xylene, and evaporated onto stainless steel disks. Alpha spectrometry is employed to determine the activity of each plutonium isotope. Each sample is spiked with plutonium-236. All glassware used in the procedure is disposable. The detection limits are 3 and 5 dpm (disintegrations per minute) for air and smear samples, respectively, with an average recovery of 87%.

The purpose of this work has been to identify aspects of cell fabrication and treatment which are critical for achieving high efficiency Cu/sub 2/S/CdS solar cells. In approaching the problem several comparisons were made of the effects of specific steps in two methods of cell fabrication. These methods had previously given cells of about 6% and a maximum of 9% efficiency. Three areas requiring special attention and specific means to achieve acceptable results were identified. (1) The Cu/sub 2/S/CdS heterojunction area must be minimized. If single source evaporations of CdS are made on substrates whose temperatures (approx. 220/sup 0/C) are monitored and controlled using welded thermocouples, the CdS films will have adequately large grains (grain diameter greater than or equal to 2 ..mu..m) and will not develop significant etch pits during texturing in a mild etchant solution. (2) The termination of the wet barrier processing steps must be done carefully. An acceptable termination involves minimizing the amount of cuprous chloride retained on the cell surface during transfer to a rinsing stage while providing adequate exclusion of air from the space above the surface of the cuprous chloride solution. (3) Once formed, the Cu/sub 2/S layer should not be exposed to …

INTERCOMP has simulated six geothermal reservoir problems. INTERCOMP's geothermal reservoir model was used for all problems. No modifications were made to this model except to provide tabular output of the simulation results in the units used in RFP No. DE-RP03-80SF-10844. No difficulty was encountered in performing the problems described herein, although setting up the boundary and grid conditions exactly as specified were sometimes awkward, and minor modifications to the grid system were necessitated. The results of each problem are presented in tabular and (for many) graphical form.

A useful gage has been developed for measuring pressure of nonplanar or obliquely incident stress waves. The measurements made with these gages are not as precise as direct strain gage measurements, but are very good considering the conditions under which these gages are used. We feel a need to further develop our ability to measure nonplanar stress waves in the 0 to 10 kbar range. Carbon or ytterbium will probably be chosen for the sensing element.

Two electrically powered mopeds were designed and built. These vehicles offer single-person transportation which is convenient, quiet, low-cost, smooth, and pollution-free. The first moped has a 12 volt electrical system. The second has a 24 volt electrical system. They both have top speeds of about 20 miles per hour. They both use transistorized speed controls and deep-discharge, lead-acid batteries. These mopeds were put through a 750 mile test program. In this program, the 12 volt bike had an average range of nine miles. The 24 volt bike, with a smaller battery capacity, had an average range of six miles.

A proposed design analysis is presented of a passive solar energy efficient system for a typical three-level, three bedroom, two story, garage-under townhouse. The design incorporates the best, most performance-proven and cost effective products, materials, processes, technologies, and sub-systems which are available today. Seven distinct categories recognized for analysis are identified as: the exterior environment; the interior environment; conservation of energy; natural energy utilization; auxiliary energy utilization; control and distribution systems; and occupant adaptation. Preliminary design features, fenestration sysems, the plenum-supply system, the thermal-storage party-fire walls, direct gain storage, the radiant comfort system, and direct passive cooling systems are briefly described. Features of the design under analysis and on which conclusions have not yet been formulated are: the energy reclamation system, auxiliary energy back-up systems, the distribution system and operating modes, the control systems, and non-comfort energy systems and inputs. (MCW)

Real-time radiography is used for imaging both dynamic events and static objects. Fluorescent screens play an important role in converting radiation to light, which is then observed directly or intensified and detected. The radiographic parameters for real-time radiography are similar to conventional film radiography with special emphasis on statistics and magnification. Direct-viewing fluoroscopy uses the human eye as a detector of fluorescent screen light or the light from an intensifier. Remote-viewing systems replace the human observer with a television camera. The remote-viewing systems have many advantages over the direct-viewing conditions such as safety, image enhancement, and the capability to produce permanent records. This report reviews real-time imaging system parameters and components.

This report summarizes results from the successful experimental operation of the Tandem Mirror Experiment (TMX) over the period October 1978 through September 1980. The experimental program, summarized by the DOE milestones given in Table 1-1, had three basic phases: (1) an 8-month checkout period, October 1978 through May 1979; (2) a 6-month initial period of operation, June through November 1979, during which the basic principles of the tandem configuration were demonstrated (i.e., plasma confinement was improved over that of a single-cell mirror); and (3) a 10-month period, December 1979 through September 1980, during which the initial TMX results were corroborated by additional diagnostic measurements and many detailed physics investigations were carried out. This report summarizes the early results, presents results of recent data analysis, and outlines areas of ongoing research and data analysis which will be reported in future journal publications.

This report summarizes results from the successful experimental operation of the Tandem Mirror Experiment (TMX) over the period October 1978 through September 1980. The experimental program, summarized by the DOE milestones given in Table 1, had three basic phases: (1) an 8-month checkout period, October 1978 through May 1979; (2) a 6-month initial period of operation, June through November 1979, during which the basic principles of the tandem configuration were demonstrated (i.e., plasma confinement was improved over that of a single-cell mirror); and (3) a 10-month period, December 1979 through September 1980, during which the initial TMX results were corroborated by additional diagnostic measurements and many detailed physics investigations were carried out. This report summarizes the early results, presents results of recent data analysis, and outlines areas of ongoing research.

A literature search and review of the studies analyzing the relationship between thermal and electrical energy demand for various industries and applications resulted in several applications affording reasonable correlation to the thermal and electrical output of the HTSOE fuel cell. One of the best matches was in the aluminum industry, specifically, the Reynolds Aluminum Production Complex near Corpus Christi, Texas. Therefore, a preliminary design of three variations of a cogeneration system for this plant was effected. The designs were not optimized, nor were alternate methods of providing energy compared with the HTSOE cogeneration systems. The designs were developed to the extent necessary to determine technical practicality and economic viability, when compared with alternate conventional fuel (gas and electric) prices in the year 1990.

Two fiber optic connectors for field use in high efficiency, long distance systems are described and evaluated in this report. The transmission testing arrangement and other considerations are included with the test results. Techniques for optimizing the transmission through these connectors are also described and the results are reported. Many desirable characteristics of connectors for field use are considered and compared to the ITT and Amphenol connectors tested here.

The seismic qualification requirements of auxiliary feedwater systems (AFWS) of Pressurized Water Reactors (PWR) were developed over a number of years. These are formalized in the publication General Design Criteria (Appendix A to 10CFR50). The full recognition of the system as an engineered safety feature did not occur until publication of the Standard Review Plan (1975). Efforts to determine how to backfit seismic requirements to earlier plants has been undertaken primarily in the Systematic Evaluation Program (SEP) for a limited number of operating reactors. Nuclear Reactor Research (RES) and NRR have requested LLNL to perform a probabilistic study on the AFWS of San Onofre Nuclear Generating Station (SONGS) Unit 1 utilizing the tools developed by the Seismic Safety Margins Research Program (SSMRP). The main objectives of this project are to: identify the weak links of AFWS; compare the failure probabilities of SONGS 1 and Zion 1 AFWS: and compare the seismic responses due to different input spectra and design values.

Optical techniques in the far infrared region (10 to 200 cm/sup -1/) are to explore the basic superconducting behavior of the high temperature superconductors V/sub 3/Si, Nb/sub 3/Ge, Nb, and granular NbN. Such spectroscopy yields accurate gap values, information about the temperature dependence of superconducting properties, values of the electron-phonon spectral function, and insight into grain-to-grain coupling in inhomogeneous geometries. These results are used to calculate basic superconducting parameters such as the coupling constant and the transition temperature with the aim of explaining the underlying physics of superconductors.

None

Progress has been ahead of planned expectations in three instances: (a) achievement of 4 mA/cm/sup 2/, short circuit current density in a MIS structure solar cell under AM1 illumination; (b) fabrication of large area (4 cm/sup 2/) MIS cells with external J/sub sc/ > 3 mA/cm/sup 2/; and (c) deposition of p/sup +/ layers by B/sub 2/H/sub 6/ gas phase doping. A program status table is included. Reproducible n layers are now routinely deposited by sputtering in Ar, H/sub 2/, and PH/sub 3/ gases. The major remaining obstacle to the goal of a 3.5% cell is the deposition of a quality i-layer. Although information deduced from infrared absorption and Raman data indicates that most of the hydrogen is bonded in the SiH configuration, the photoconductivity of the intrinsic material requires marked improvement. Two forms of magnetron sputtering, planar and cylindrical, are being exploited. The planar deposition system has the advantage that experimental costs are low; the cylindrical system is easily scalable to large product throughput. Schematic illustrations of the two systems and descriptions of apparatus modifications incorporated are included.

The requirements for the design and test of terrestrial solar cell modules for one phase of DOE's Low-Cost Solar Array Project are presented. Intermediate-load modules designed to meet this specification will generally have the following design features and characteristics: (1) nominal operating voltage (V/sub no/) between 5 Vdc and 20 Vdc; (2) ability to be series-connected to worst-case open-circuit voltages of 1000 Vdc; (3) dimensions not exceeding 1.22 m x 2.44 m (4 ft x 8 ft); (4) flat-plate configuration (non-concentrating); and (5) output power referenced to nominal operating conditions and V/sub no/. In addition to module design and performance requirements, a series of characterization and qualification tests are also specified.

A water source heat pump has been designed that is capable of operating over the range from 40 to 110/sup 0/F entering water temperature and has a heating coefficient of performance greater than six in the upper portion of this range. A computerized heat pump balance program was written to allow the performance of either a water-to-water or a water-to-air heat pump to be predicted in either the heating or cooling mode. A detailed program description, flow charts, and sample outputs are appended. The balance program was used to specify components for a high efficiency water-to-water and a high efficiency water-to-air heat pump. Performance predictions for both units in heating and in cooling are included. The water-to-water and water-to-air performance predictions were compared. The water-to-air approach was clearly superior. A detailed design and layout was done for the three solar-assisted water-to-air heat pump. A horizontal configuration was chosen for marketability reasons. The design was made consistent with high quantity production equipment available in our factories and should result in the lowest possible manufacturing cost. A key question to be answered in this project is whether a reciprocating compressor can operate without damage at the high suction pressures characteristic to the …

Tests are continuing on the shatter-resistant weathercase models and small samples. Extensive studies of composite materials has resulted in characterization of the epoxy weathercase materials mechanical properties over a wide range of temperatures and lifetime. Progress is reported on the design of the full scale prototype termination.

We have completed our evaluation of candidate longwall mines available for study in the Rocky Mountain Coal Province. This report summarizes our views and evaluation of two candidate mines, the Allen Mine in Weston, Colorado, and the Hawk's Nest Mine in Somerset, Colorado. WCC visited the Allen and the Hawk's Nest Mines, and rated them in order of preference for subsidence monitoring according to criteria given in this report. Based on these evaluations and related discussions with the Technical Project Officer, the Hawk's Nest Mine appears to be the preferred mine for subsidence monitoring, because it is the only candidate mine offering two adjacent longwall panels for monitoring wherein a full subsidence profile may be obtained for at least one of the panels. Selection of this mine requires that provisions be made for monitoring 2000 ft of overburden, whereas our proposal addressed a mine with 600 ft of overburden. Changes in instrumentation which may permit the project to remain within the current budget were investigated and are discussed.

The procedures and status of the absolute measurement of the neutron capture cross sections for /sup 115/In and /sup 232/Th are described. Work on the /sup 239/Pu fission fragment anisotropy and absolute measurement of the fast neutron fission cross section for /sup 233/U are briefly described. Progress in establishing the 14 MeV neutron measurements at the facility are discussed. (WHK)

A digitally based deflection generator for an electron-beam welder is presented. Up to seven patterns of any shape are stored in programmable read-only memory (PROM). The pattern resolution is 39% at frequencies from 10 Hz to 1 kHz and can be x-t, y-t, or x-y formed. Frequency and pattern selections may be chosen by the welder computer or manually selected on the front panel. The ability to repeatedly synchronize two waveforms of any shape and frequency enables an unlimited variety of welds.