This report

The primary objective of this work was to demonstrate that copper silver selenide and TAGS could be segmented. The hot junction temperature was planned to be 725/sup 0/C with the segmentation temperature at 400/sup 0/C, both temperatures were selected to prevent excessive sublimation from the hot ends of the segments, respectively. The program was planned as a cooperative effort between General Atomic company and Teledyne Energy Systems. Accordingly, General Atomic synthesized the CuAgSe that was used to fabricate the test hardware that was ultimately delivered to General Atomic for testing. Both the CuAgSe and TAGS were hot pressed in an argon atmosphere then the segments were furnace-bonded to each other. A secondary objective was to produce CuAgSe powder by rapid solidification.

Progress has been ahead of planned expectations in three instances: (a) achievement of 4 mA/cm/sup 2/, short circuit current density in a MIS structure solar cell under AM1 illumination; (b) fabrication of large area (4 cm/sup 2/) MIS cells with external J/sub sc/ > 3 mA/cm/sup 2/; and (c) deposition of p/sup +/ layers by B/sub 2/H/sub 6/ gas phase doping. A program status table is included. Reproducible n layers are now routinely deposited by sputtering in Ar, H/sub 2/, and PH/sub 3/ gases. The major remaining obstacle to the goal of a 3.5% cell is the deposition of a quality i-layer. Although information deduced from infrared absorption and Raman data indicates that most of the hydrogen is bonded in the SiH configuration, the photoconductivity of the intrinsic material requires marked improvement. Two forms of magnetron sputtering, planar and cylindrical, are being exploited. The planar deposition system has the advantage that experimental costs are low; the cylindrical system is easily scalable to large product throughput. Schematic illustrations of the two systems and descriptions of apparatus modifications incorporated are included.

The risks associated with geothermal hydrothermal commercialization are broken down into five categories: resource risk; technological risk; regulatory risk; investment parity risks; and institutional risk aversion. The impact of each risk upon geothermal financing is assessed. The federal government's programs to provide financial incentives for geothermal development are presented as follows: tax incentives; indirect financial incentives programs; direct grant/cost-sharing programs; and attempts at reducing regulatory risk through the enactment of legal and institutional reforms. (MHR)

Fiber-reinforced composite materials are being widely used in engineered structures. This report examines how the general form of the Weibull Criterion, including the evaluation of the parameters and the scaling of the parameter values, can be used for the prediction of component failure.

A device is described for indicating and preventing damage to voltage cells such as galvanic cells and fuel cells connected in series by detecting sequential voltages and comparing these voltages to adjacent voltage cells. The device is implemented by using operational amplifiers and switching circuitry is provided by transistors. The device can be utilized in battery powered electric vehicles to prevent galvanic cell damage and also in series connected fuel cells to prevent fuel cell damage.

The requirements for the design and test of terrestrial solar cell modules for one phase of DOE's Low-Cost Solar Array Project are presented. Intermediate-load modules designed to meet this specification will generally have the following design features and characteristics: (1) nominal operating voltage (V/sub no/) between 5 Vdc and 20 Vdc; (2) ability to be series-connected to worst-case open-circuit voltages of 1000 Vdc; (3) dimensions not exceeding 1.22 m x 2.44 m (4 ft x 8 ft); (4) flat-plate configuration (non-concentrating); and (5) output power referenced to nominal operating conditions and V/sub no/. In addition to module design and performance requirements, a series of characterization and qualification tests are also specified.

June 1, 1981-August 31, 1981 was the third consecutive quarter of superheated steam injection at the BX In Situ Oil Shale Project. Injection was continuous except for the period of July 14th to August 1st when the injection was suspended during the drilling of core hole BX-37. During the quarter, 99,760 barrels of water as superheated steam were injected into Project injection wells at an average well head temperature of 752/sup 0/F and an average wellhead pressure of 1312 PSIG. During the same period, 135,469 barrels of fluid were produced from the Project production wells for a produced to injected fluid ratio of 1.36 to 1.0. Net oil production during the quarter was 38 barrels.

September 1, 1981-November 30, 1981, was the fourth consecutive quarter of superheated steam injection at the BX In Situ Oil Shale Project. During the quarter, 117,520 barrels of water as steam were injected into project injection wells at an average wellhead temperature of 715/sup 0/F and an average wellhead pressure of 1378 PSIG. During the same period, 148,516 barrels of fluid were produced from the project production wells for a produced-to-injected fluid ratio of 1.26 to 1.0. Net oil production for the quarter was 169 barrels.

This report details the results of a theoretical study of seismic coupling and decoupling of underground explosions in a salt medium. A series of chemical and nuclear explosions was carried out years ago in salt domes for the Cowboy and the Dribble programs to provide experimental data on seismic coupling for both tamped explosions and explosions in cavities. The Cowboy program consisted of a series of chemical explosions, and the Dribble program consisted of the tamped nuclear Salmon event, the Sterling nuclear event in the Salmon cavity, and an associated site calibration effort. This report presents the results of extensive computer calculations, which are in satisfactory agreement with the experimental data. The calculations were extended to give general results on seismic coupling in salt. The measure of seismic coupling for most of this work was the residual reduced displacement potential (residual RDP). The decoupling associated with a shot in a cavity was expressed as the ratio of the resulting residual RDP to that of an equal-sized tamped shot.

Four sources or error (uncertainty) are studied in water content obtained from neutron logs calibrated in partially saturated media for holes up to 3 m. For this calibration a special facility was built and an algorithm for a commercial epithermal neutron log was developed that obtains water content from count rate, bulk density, and gap between the neutron sonde and the borehole wall. The algorithm contained errors due to the calibration and lack of fit, while the field measurements included uncertainties in the count rate (caused by statistics and a short time constant), gap, and density. There can be inhomogeneity in the material surrounding the borehole. Under normal field conditions the hole-size-corrected water content obtained from such neutron logs can have an uncertainty as large as 15% of its value.

The FMA Linear Pocket Feeder (LPF) is a positive displacement feed system in which the pressure seal is developed by a set of mechanical labyrinth seals between the piston rings and the sealing tube. The pressure seal is completely independent of the type and size of coal used. The LPF can maintain a pressure difference with no coal in the system and can achieve steady state operation in less than a minute after startup. Coal flow rate can be changed while the LPF is operating at design speed and operating pressure with no effect on the LPF's performance. The LPF has the potential for operating on all types and sizes of coal as long as they are free flowing. The existing LPF will be upgraded utilizing the knowledge gained during the previous 330 hours of operation. The loading station will be redesigned to allow the infeed of coarse coal in such a manner that minimum degradation occurs during entry into the pockets of the feeder and feed of pulverized coal in a way that minimizes entrapment of air under the coal charge to allow quicker settling. Certain other proposed design changes are described also. (LTN)

The Lawrence Livermore National Laboratory (LLNL) has the necessary equipment and trained personnel to respond to a large number of hazardous material spills and fires or other emergencies resulting from these spills including injured personnel. This response capability is further expanded by the agreements that LLNL has with a number of outside response agencies. The Hazards Control Department at LLNL functions as the central point for coordinating the response of the equipment and personnel. Emergencies involving hazardous waste are also coordinated through the Hazards Control Department, but the equipment and personnel in the Toxic Waste Control Group would be activated for large volume waste pumpouts. Descriptions of response equipment, hazardous waste locations communication systems, and procedures for personnel involved in the emergency are provided.

The hydrogen embrittlement susceptibility of commercial 2-1/4 Cr-1Mo steels has been investigated, using H/sub 2/S as the primary environment. After it was found that low strength steels, which had been given a post weld heat treatment, were immune to the test techniques developed, the effect of strength level was studied to establish a lower limit for embrittlement. Similar tests on the peak hardness zone in the heat affected zone of a weld showed that the crack preferred to move to the far heat affected zone where the strength level was below the lower limit established above. It is suggested that residual stresses may account for the anomaly, although other factors such as structural change could be important. In order to assess the low strengh steels, the environment was changed to include saturated water vapor in the H/sub 2/S. It was found that the low strength steels could be readily tested in this environment, thus providing a means of ranking Cr-Mo steels for hydrogen embrittlement susceptibility. Tests on one steel were included to show that the variability in the data using the H/sub 2/S + H/sub 2/O environment was small enough to make the screening test results significant.

The High-Field Test Facility (HFTF) project has two primary goals. The first is to establish manufacturing capability for a Nb/sub 3/Sn conductor suitable for use in a mirror fusion coil. The second is to provide a test facility for evaluating other fusion conductor designs at high fields. This paper describes some of the problems encountered and the solutions devised in working toward the first goal. Construction of the test facility coils will be described in a subsequent paper.

A water source heat pump has been designed that is capable of operating over the range from 40 to 110/sup 0/F entering water temperature and has a heating coefficient of performance greater than six in the upper portion of this range. A computerized heat pump balance program was written to allow the performance of either a water-to-water or a water-to-air heat pump to be predicted in either the heating or cooling mode. A detailed program description, flow charts, and sample outputs are appended. The balance program was used to specify components for a high efficiency water-to-water and a high efficiency water-to-air heat pump. Performance predictions for both units in heating and in cooling are included. The water-to-water and water-to-air performance predictions were compared. The water-to-air approach was clearly superior. A detailed design and layout was done for the three solar-assisted water-to-air heat pump. A horizontal configuration was chosen for marketability reasons. The design was made consistent with high quantity production equipment available in our factories and should result in the lowest possible manufacturing cost. A key question to be answered in this project is whether a reciprocating compressor can operate without damage at the high suction pressures characteristic to the …

One of the end plug configurations we have investigated for use in a tandem mirror reactor is the axisymmetric cusp. We show that because of non-adiabaticity, the containment of 3.5 MeV alpha particles in this configuration is insufficient for the attainment of acceptable plasma performance.

A program to provide the basis for designing a practical electrochemical solar cell based on the II-VI compound semiconductors is described. Emphasis is on developing new electrolyte redox systems and electrode surface modifications which will stabilize the II-VI compounds against photodissolution without seriously degrading the long-term solar response. Work on redox couple stabilization of n-CdX photoanodes has focused on fast metal-based one-electron couples in various nonaqueous solvents which represent an extension of work with the methanol/ferro-ferricyanide system, which, although stabilizing for n-CdSe photoanodes, has been found to be photolytically unstable. Very promising results which were obtained for the FeCl/sub 4//sup 1-/2-/ couple in acetonitrile suggest that related chloro-couples should be considered, including the colorless two-electron tin (II, IV) and antimony (III, V) systems. Conducting polymer films of polyrrole photoelectrochemically deposited onto n-type semiconductors were previously shown to protect these electrode materials from photodecomposition while permitting electron exchange with the electrolyte, but poor adhesion has remained a key problem. Recently, improved adhesion has been attained for roughened semiconductor surfaces. It now appears that polypyrrole films are to some extent permeable to solvent/solute species since the film stability depends on the nature of the redox electrolyte, and semiconductor decomposition products seem to …

The ECRH diagnostics system monitors the net power delivered to the plasma by four 200-kW gyrotron oscillators, the frequency of each gyrotron, and some operating parameters of the gyrotron power supply system. The combination CAMAC- and GPIB-based data acquisition system is under desktop computer control that provides the capability for data conversion and display. The data acquisition system is also interfaced to the main computer system that acquires and archives the data.

The twenty-three (23) MFTF sustaining neutral beam arc power supplies were designed to provide 0.3 to 30 second output pulses over a range of 24 to 71 volts and 600 to 4000 amperes at 10 percent duty. For economic reasons, the circuit design consists of a 12 pulse rectifier which is asynchronously switched on and off by a three phase electromechanical contactor in the primary ac input. The paper describes the analysis of the problem, various possible solutions considered, and the simple and inexpensive solution adopted for use.

Tests are continuing on the shatter-resistant weathercase models and small samples. Extensive studies of composite materials has resulted in characterization of the epoxy weathercase materials mechanical properties over a wide range of temperatures and lifetime. Progress is reported on the design of the full scale prototype termination.

The results of an accurate determination of the recoil spectrum from (n, ..gamma..) reactions in molybdenum are presented. The recoil spectrum has been calculated from nuclear level structure data and measured branching ratios. Angular correlations between successive gammas have been accounted for using the standard theoretical techniques of Racah algebra and the density matrix formalism.

The present paper represents the first effort to date in which a combined experimental and theoretical approach has been used to study the effects of several inhibitors on hydrocarbon-air flames. This work is part of an attempt to build a consistent picture of chemical kinetic flame inhibition, beginning with a simple halogen molecule such as HBr and progressing sequentially towards more complex and more practical inhibitors such as CF/sub 3/Br. Inhibition efficiency can be defined as the rate of flame speed reduction, the amount of flame speed change per unit inhibitor added. Both the numerical model and the flame tube measurements found that the inhibition efficiency gradually decreases as the amount of inhibitor is increased. The present experimental and modeling results are shown, together with earlier data for CF/sub 3/Br-CH/sub 4/-air and CF/sub 3/Br-C/sub 3/H/sub 8/-air as well as HBr-CH/sub 4/-air, CH/sub 3/Br-CH/sub 4/-air and CF/sub 3/Br-CH/sub 4/-air. In the numerical study it was found that a stoichiometric methane-air mixture with up to 8% methyl bromide could support a flame, propagating at a speed of about 5 cm/sec, even though the addition of the first 1% of CH/sub 3/Br had reduced the flame speed from 38 cm/sec to about 26 …

The backscattering of energetic hydrogen particles, 1-1000 eV, from alkali metal surfaces provides for a relatively large yield of negative hydrogen ions. These yields are enhanced by particle reflection from surfaces consisting of partial alkali coatings over high-Z transition-metal substrates. The theoretical data supporting these observations are reviewed. The parameters leading to optimum reflection yields are summarized. In the volume of a hydrogen discharge with electron temperatures of about one electron volt, negative ions are formed by dissociative attachment to vibrationally excited molecules. The vibrational distribution is determined by e-V collisions between low energy electrons and vibrationally excited molecules, E-V singlet electron excitation processes caused by high energy (100 eV) electrons colliding with ground state molecules exciting to electronic states followed by radiative decay to higher vibrational levels, and V-T collisions between molecules resulting in transfer of vibrational excitation to translational energy. The role of these different processes as they bear on the vibrational distribution is discussed. The possibility of a volume-surface interaction leading to a high volume density of negative ions is considered.