The details of a shingle module design which produces in excess of 97 watts/m/sup 2/ of module area at 1 kW/m/sup 2/ insolation and at 60/sup 0/C are reported. This selected design employs a tempered glass coverplate to provide the primary solar cell structural support. The use of the B.F. Goodrich FLEXSEAL roofing system as the outer skin of the shingle substrate provides a high confidence of achieving the 15 year service life goal. The fabrication and testing of a preproduction module of this design has demonstrated that this selected approach will meet the environmental testing requirements imposed by the contract. Attempts to fabricate a preproduction module of an alternative design, which embeds the solar cell assembly within a methyl methacrylate casting, proved unsuccessful.

An investigation of available data on the saturation state of seawater with respect to calcium carbonate and its possible significance for scale formation on Ocean Thermal Energy Conversion (OTEC) heat exchangers has been carried out. Pertinent oceanographic data is lacking at or near potential OTEC sites for the calculation of the degree of saturation of seawater with respect to calcium carbonate. Consequently, only ''extrapolated'' saturation values can be used. These indicate that near surface seawater is probably supersaturated, with respect to the calcium carbonate phases calcite and aragonite, at all potential OTEC sites. The deep seawater that would be brought to the surface at the potential Atlantic Ocean sites is also likely to be supersaturated with respect to calcium carbonate. The deep seawater at the potential Pacific Ocean sites may be slightly undersaturated. The fact that OTEC heat exchangers will be operating in seawater, which is supersaturated with respect to calcium carbonate, means that if nucleation of calcite or aragonite occurs on the heat exchanger surfaces, significant growth rates of calcium carbonate scale may be expected. The potential for calcium carbonate nucleation is highest at cathodic metal surface locations, which are produced as the result of aluminum corrosion in seawater. …

Expanded development of total-flow expander technology in order to obtain efficient energy extraction from the liquid flow component of the geothermal well flow, in addition to steam enthalpy conversion, has been undertaken by the University of California, Lawrence Livermore Laboratory (LLL). The flow conditions necessary for this type of complete system performance characterization are beyond the capabilities of the test facility utilized in the preliminary tests at the LLL hot-water test facility. As an alternative to increasing the existing facility to meet the expanded test requirements, test facilities in the industrial California community are being surveyed to assess their capability in supporting future tests of the LLL expander. Biphase Engines, Inc. of Santa Monica, California was contracted by LLL to perform this survey. The goal of the Biphase Engines survey is to identify organizations with, first, an interest in supporting the LLL turbine test program and, second, to review their test capabilities with respect to the turbine test requirements. The results of the survey are described in the following sections which includes a listing of all organizations contacted. The responses to all inquiries are given. The affirmative responses to the test-support requirement are detailed with a description of the test …

The objective of Phase I of this project is to support the Solar Central Receiver Power Plant research, development and demonstration effort by: (1) Establishment of a heliostat design, with associated manufacturing, assembly, installation and maintenance approaches, that, in quantity production will yield significant reductions in capital and operating costs over an assumed 30 year plant lifetime as compared with existing designs. (2) Identification of needs for near term and further research and development in heliostat concept, materials, manufacture, installation, maintenance, and other areas, where successful accomplishment and application would offer significant payoffs in the further reduction of the cost of electrical energy from Solar Central Receiver Power Plants. The Phase I study will define a low-cost heliostat preliminary design and the conceptual design of a heliostat manufacturing/installation plan which will result in low life cycle cost when produced and installed at high rate and large quantities for commercial Solar Central Receiver Power Plants. The study will develop the annualized life cycle cost and the performance of heliostats for a 30 year plant life, for each of three rates of continuous production and installation. The three specified rates are 25,000, 250,000, and 1,000,000 heliostats per year. The analysis of these …

During the past quarter, 5 runs were made on a number of hydrotreated samples including a mildly hydrotreated simulated in-situ (1.35% N) and two moderately hydrotreated Tosco II (0.82% N and 1.55% N) distillates. The results are, in general, consistent with previous results which indicated an increase in olefins yield as the severity of hydrogenation increased. The olefins yields for the simulated in-situ oil were greater than those for the Tosco II oil for oil hydrogenated to comparable severities. The moderately hydrogenated Tosco II oil exhibited gasification tendencies at severe pyrolysis conditions, similar to the severely hydrogenated Tosco II oil. Correlational efforts were continued in using the propylene yield versus severity factor, and the yields of all major gas components versus propylene to ethylene ratio as a means of correlating pyrolysis yields. The efforts were extended to the hydrogenated simulated in-situ and Tosco II distillates.

A subscale, direct contact heat exchanger (1-ft dia packed column) was built and operated under conditions applicable to the Biphase diesel bottoming cycle. Special probes for measuring gas and liquid temperatures and for measuring gas-phase compositions were designed and installed in the exchanger. The data obtained are unique in that they indicate both the extent of evaporation and condensation zones within the exchanger and the effect that those mass transport mechanisms have upon heat exchanger performance. For gas temperatures greater than 500/sup 0/F it was found that the maximum temperature to which Therminol 66 could be heated was strongly dependent upon vaporization effects. Data obtained are sufficient to provide for the preliminary design of a direct contact heat exchanger using Therminol 66 as the thermal fluid. Recommendations are made for further testing using other heat transfer fluids to derive a more general engineering approach to the design of direct heat exchangers.

The purpose of this manual is to present procedures to execute the Spent Nuclear Fuel Storage Model (SNFSM) program. This manual includes an overview of the model, operating environment, input and output specifications and user procedures. An example of the execution of the program is included to assist potential users.

Most detailed fusion target design is done by numerical simulation using large computers. Although numerical simulation is briefly discussed, this lecture deals primarily with the way in which basic physical arguments, driver technology considerations and economical power production requirements are used to guide and augment the simulations. Physics topics discussed include target energetics, preheat, stability and symmetry. A specific design example is discussed.

The fabrication and testing phase of the program to develop a shingle-type solar cell module is well underway. Six modules are currently being subjected to a qualification testing program which consists of both thermal cycling and humidity exposures followed by a mechanical integrity test to simulate wind loads. Fabrication of the remainder of the 50 deliverable modules is proceeding.

The cyclone incinerator was operated throughout the past quarter, generating additional data on system characteristics, equipment life expectancies, and by-product generation. Several changes in the incinerator system are in various stages of completion. The lid assembly, secondary chamber, and expansion unit for the new exhaust equipment are nearly ready for installation. A new heat exchanger has been installed in the scrubber system. An ash handling system has been designed for possible future addition to the system. Continuing studies will determine the best delivery mechanism for continuously feeding the cyclone incinerator. Preliminary investigations are being conducted to select an independent system to treat incinerator scrubber solution for recycling and to remove salts and sludge for disposal. Metal samples of two possible materials for incinerator construction were examined for corrosion degradation suffered at the incinerator exhaust outlet. Controlled experiments were conducted on the pressed ash-cement pellet matrix to define compressive strength, mechanical stability, density, and effect of curing environment (wet cure and dry cure). Leachability studies were initiated on pressed sludge/cement matrix in distilled water at ambient temperature. Compressive strengths of sludge/cement pressed matrix samples were investigated. Physical and chemical attributes of incinerated ash were evaluated in relationship to the ash/cement matrix.

Experimental values for the kerma per unit fluence at the neutron energy, E/sub n/ = 15 MeV, have been determined for graphite, Mg, and Fe. Ion chambers of small size with walls of these materials were employed, and were filled with a variety of gases--N/sub 2/, CO/sub 2/, Ne, Ar, Kr, and Xe. A calibrated neutron source was employed, allowing a straightforward determination of the kerma per unit fluence.

Consider the problem of testing goodness-of-fit to a specified location-scale family when evidence is to be combined from several independent samples, from populations with possibly different location and scale parameters. The procedure studied is that of computing standardized residuals from each sample and then combining these into one set to be treated essentially as though they came from one sample. It is shown that the limiting distribution of any location-scale invariant goodness-of-fit statistic so applied is precisely the same as for the corresponding one-sample problem. 13 references.

The purpose of this investigation was to determine the corrosion behavior of a high strength steel (ASTM A416-74 grade 270), typical of those used as tensioning tendons in prestressed concrete pressure vessels, in several corrosive environments and to demonstrate the protection afforded by coating the steel with either of two commercial petroleum-base greases or Portland Cement grout. In addition, the few reported incidents of prestressing steel failures in concrete pressure vessels used for containment of nuclear reactors are reviewed. The susceptibility of the steel to stress corrosion cracking and hydrogen embrittlement and its general corrosion rate were determined in several salt solutions. Wires coated with the greases and grout were soaked for long periods in the same solutions and changes in their mechanical properties were subsequently determined. All three coatings appeared to give essentially complete protection but small flaws in the grease coatings were detrimental; flaws or cracks less than 1 mm wide in the grout were without effect.

A filter fluorescer experiment has been installed and operated on the Argus laser system of the Lawrence Livermore Laboratory. X-ray spectra have been measured between 20 and 116 keV from laser produced plasmas. Three spectral cuts were made in this region (20 to 29, 47 to 61 and 80 to 116 keV) with an additional channel providing a measure of the high energy response (> 116 keV) of the third channel. We have measured x-ray spectra from laser shots of 600 to 900 J in 1 ns with intensities of 3 x 10/sup 14/ to 3 x 10/sup 15/ W/cm/sup 2/ incident on Au disks.

The FRS is a pool structure and enclosing building constructed in 1966 for storing spent nuclear fuel. The enclosing building was not analyzed. The pool structure's responses to operating loads, seismic excitation, and an accidentally dropped cask were determined. Locations in the FRS pool were identified where structural strength would be exceeded in the event of an earthquake of 0.2 g maximum ground acceleration or an accident in which a cask dropped from the maximum height of the crane hook used to maneuver it. 25 figures, 4 tables.

The Emergency Core Cooling System (ECCS) for the LOFT reactor may need to be disabled for modifications or repairs of hardware or instrumentation or for component testing during periods when the reactor system is hot and pressurized, or it may be desirable to enable the ECCS to be disabled without the necessity of cooling down and depressurizing the reactor. LTR 113-47 has shown that the LOFT ECCS can be safely bypassed or disabled when the total core power does not exceed 25 kW. A modified policy involves disabling the automatic actuation of the LOFT ECCS, but still retaining the manual activation capability. Disabling of the automatic actuation can be safely utilized, without subjecting the fuel cladding to unacceptable temperatures, when the LOFT power decays to 70 kW; this power level permits a maximum delay of 20 minutes following a LOCA for the manual actuation of ECCS.

The laboratory cyclone incinerator, which started operation in January, 1978, has been developed to study the effects of burning feed containing radionuclides other than /sup 238/Pu. These isotopes must be removed from the off-gas during incineration. Preliminary data from early runs show that the combustion efficiency of the incinerator can still be improved. Controlled experiments were conducted on the pressed ash-cement pellet matrix to define compressive strength, mechanical stability, density, and effect of curing environment (wet cure and dry cure). Leachability studies were initiated on pressed sludge/cement matrix in distilled water at ambient temperature. Compressive strengths of sludge/cement pressed matrix samples were investigated. Physical and chemical attributes of incinerated ash were evaluated in relationship to the ash/cement matrix. 7 figs., 6 tables.

Lawrence Livermore Laboratory is conducting a safeguards program for the Nuclear Regulatory Commission. The goal of the Material Control Project of this program is to evaluate material control and accounting (MCA) methods in plants that handle special nuclear material (SNM). To this end we designed and implemented the dynamic chemical plant simulation program DYNSYL. This program can be used to generate process data or to provide estimates of process performance; it simulates both steady-state and dynamic behavior. The MCA methods that may have to be evaluated range from sophisticated on-line material trackers such as Kalman filter estimators, to relatively simple material balance procedures. This report describes the overall structure of DYNSYL and includes some example problems. The code is still in the experimental stage and revision is continuing.

Document issued by the Office of the Attorney General of Texas in Austin, Texas, providing an interpretation of Texas law. It provides the opinion of the Texas Attorney General, John L. Hill, regarding a legal question submitted for clarification; Validity of proposed rules of the Texas Antiquities Committee which would require underwater cultural resource survey guidelines.

Document issued by the Office of the Attorney General of Texas in Austin, Texas, providing an interpretation of Texas law. It provides the opinion of the Texas Attorney General, John L. Hill, regarding a legal question submitted for clarification;Payment for return transportation to Texas of Juvenile runways.

Document issued by the Office of the Attorney General of Texas in Austin, Texas, providing an interpretation of Texas law. It provides the opinion of the Texas Attorney General, John L. Hill, regarding a legal question submitted for clarification; Whether article 6252 llc V.T.C.S apply to audits.

Document issued by the Office of the Attorney General of Texas in Austin, Texas, providing an interpretation of Texas law. It provides the opinion of the Texas Attorney General, John L. Hill, regarding a legal question submitted for clarification; Whether the Texas Department of Agriculture may issue a nursery inspection certificate based on inspection of premises when no nursery stock is present.

Document issued by the Office of the Attorney General of Texas in Austin, Texas, providing an interpretation of Texas law. It provides the opinion of the Texas Attorney General, John L. Hill, regarding a legal question submitted for clarification; Whether a county may pay claims for supplies and services rendered to the Sheriff's Department without a purchase order when the commissioners court has issued a written order that the claim be paid.

Document issued by the Office of the Attorney General of Texas in Austin, Texas, providing an interpretation of Texas law. It provides the opinion of the Texas Attorney General, John L. Hill, regarding a legal question submitted for clarification; Applicability of Texas Speedy Trial Act to juvenile cases.