In the Sulfex process, stainless steel cladding, generally 304-L, is removed from fuel elements by dissolution in boiling four to six molar sulfuric acid. When cladding removal is complete, the decladding solution is removed is removed to waste. The exposed fuel cores are rinsed and dissolved in nitric acid.

This report describes progress made in the study of the feasibility of the concept, plant arrangement studies, and considerations pertaining to partial plant attendance. It is concluded that both the indirect and direct boiling cycles are feasible. The recommended reference design is the direct cycle, in a single capsule, with the turbine, generator and pumps on a single shaft.

The following document describes the usage and results of sending pulsed beams of electrically charged particles with electrically wide range of pulse lengths and pulse repetition rates.

The most important component required for the Astron experimental facility is a high energy, high current, pulsed electron accelerator. A thin cylindrical layer of high energy electrons trapped within an axially symmetric magnetic field is the key feature of the Astron thermonuclear device. The trapping magnetic field is constant in time. Therefore, it is not possible to inject electrons and trap the electrons in this field unless during the injection phase a part of the electron energy is absorbed by some friction process. This is accomplished by means of eddy currents generated on suitable passive circuits by the current of the injected electron bunch. This method has ben described elsewhere. However, in order to achieve an effective loss mechanism the current of the injected electron beam must be over one hundred amps. Such high current beams are difficult to handle except if the electron energy is high enough so that the electrostatic repulsive force is compensated to great extent by attractive magnetive forces. Hence the electron energy required is 5 Mev or higher. Other requirements on the electron layer yield the same result.

An approximate Boltzmann equation, known as the single relaxation model is studied here. This equation is linearized and the fundamental solution is considered. Following N. Grad, the solution, asymptotic in small values of the ratio of mean-free-path to distance from the origin, is sought. It can be shown that the fundamental solution itself gives the asymptotic description of the flow field past an object. This solution gives the asymptotic description when the distance from the origin is much greater than either the mean-free-path or the body size. This is true independently of the Knudsen number.

A prototype instrument has been designed and built which demonstrates an ultrasonic pulse echo technique of measuring metal thickness in the range .010 to .080 inches. Extension of the range of measurement on the thick side appears straightforward, however, transducer frequency response considerations may limit the extension of the method for very thin sections. The instrument is based upon the principle that sections, when driven by pulses of vibratory energy, resonate at frequencies dependent upon the thickness of the section.

"Dust and gas masks and respirators have been an effective method under certain environmental conditions to reduce the inhalation of toxic aerosols. Under many conditions, however, their efficacy has been seriously questioned. It is the purpose of this study to evaluation over-all respirator performance on fine aerosols and to develop equipment whereby a greater degree of respiratory protection may be assured with reliability for highly toxic atmospheres."

Quarterly report describing progress on a project to develop and evaluate high-temperature tungsten alloys. This report discusses properties for specific base alloys at room temperature and under high temperatures.

Individual Samarkand wildtype D. melanogaster males were permitted to choose between either two white-eyed or two red-eyed females or between a red-eyed and a white-eyed female. Observations of the flies were made over a period of about two hours and premating periods, intermating periods and the durations of copulations were recorded.

A reliable spline disposal system is necessary for full utilization of the Poison Spline Control System. The spline choppers were not reliable enough so a spline coiler was developed and designed to replace the choppers. A Development Test, IP-306-X (HW-63820), was issued authorizing on-pile testing of the spline coiler at X area. This report closes the Development Test and discusses the use of spline coilers.

The fabricability, elevated temperature strength, steam corrosion resistance, and hydrogen pickup of various binary, ternary, and quaternary alloys were studied experimentally.

At present, emphasis is being given the application of nondestructive testing to the inspection of nuclear fuel in conjunction with complete product specifications. The objective is to quantitatively specify fuel quality parameters, and to measure the entire fuel production against these specifications nondestructively. Under this concept the acceptability of a given fuel element becomes a well-defined factor readily determined by appropriate nondestructive tests.

It is the purpose of this report to explain the bands and uses of a digital computer program for the calculation of steady state steam-water pressure drop and critical flow in pipes. The program has been coded for the IBM 709 computer. While so attempt has been made to obtain improved models of two-phase flow, it is believed that the numerical integration technique used in the code will permit more accurate calculation where pressure drops are large compared to the upstream pressure. The technique should lend itself readily to any improved correlations which appear in the future.

Two types of enclosed hot junction arrangements are possible with sheathed mineral insulated thermocouples. They are the integral junction and he isolated junction. The integral junction is formed by welding, soldering, brazing or forging the two wires into the end of the sheath. The process forms a good thermal and electrical contact between the three materials.

Absolute (p,n) cross sections have been measured for Ti47, V51, Cr52, Co59, and Cu63 at energies between 4 and 6.5 Mov. These data plus earlier measurements of the cross section for inelastic proton scattering have been used to estimate total proton absorption cross sections for V51 and Co59. An optical model calculation using parameters giving a good fit to elastic scattering measurements predicts an absorption cross section in good agreement with the measurements for Co59. For V51, some sets of parameters gave good agreement with the measured absorption cross section, but the fit to the elastic scattering data was only fair.

In answer to the question, "How well do we know the composition of the fuel material for the PRTR start-up tests?", the analytical data on the PRTR fuel elements and other fuel elements which were fabricated by similar processes was gathered and analyzed. The results of this analysis are presented.

Work on the preparation of graphite spheres containing thorium oxide for use as breeder elements in the Pebble Bed Reactor-Steam Power Plant is described. Graphite spheres of varying density were infiltrated with thorium nitrate solutions, followed by denitration to thorium oxide.

One of the primary reasons for operating the high pressure KER loops is to obtain information concerning water quality control characteristics for recirculating water cooled reactors. The KER-1 loop is predominantly carbon steel and approximates the water quality conditions specified for the New Production Reactor (NPR).

This report describes the work carried out in 321 Building semiworks equipment, to define the factors contributing to high corrosion-product contamination and presents recommendations for reducing the impurity level to meet current specifications (maximum of 200 parts total metals per million parts U).

Tory 11-A, the first experimental reactor in the Pluto nuclear ramjet program, will be tested in late 1960 at the Nevada Test Site of the Atomic Energy Commission. The fundamental objective of Tory II-A is to demonstrate that a high power density, high-temperature, air-cooled reactor can be successfully designed, constructed, and operated. This application places requirements on the reactor control system which are considerably more stringent than those found in previous reactor systems, both from the standpoint of radiation environment and system performance. To fulfill the system requirements a high-performance reactor control system has been designed and built; control actuation hardware has been developed which can withstand the high-radiation environment of Tory LI-A. This actuation system features radiation-tolerant electrohydraulic components: actuators, servo-valves, solenoid valves, feedback transducers, accumulators and associated hydraulic components. To provide high reliability against undesired shutdowns while carrying out high power level transients, the Tory 11-A control philosophy includes a new concept in reactor safety: reliance on a nonlocking, fast-reset safety system during accident situations. The fast-reset system acts so as to hold the programmed power level rather than initiating an irreversible "scram" action. A reactor "scram", if tolerated, could produce thermal shocks which would seriously damage the …

"We want to point out that there is a possible method for determining the anomalous magnetic moment of the Λ from the observation of metastable states of hyperframents. There are two possible sources for the apparent difference of binding energies of a hyperfragment. One of these comes from the difference of Q values due to the decay into an excited and ground states of the residual nucleus. The other possibility will arise if there exists a metastable state of the decaying hyperfragment."

Exponential and critical approach type measurements have been made to determine the critical mass, material buckling, and in a few cases, the extrapolation length for the lattices. This report attempts to list all measurements on water-uranium heterogenous lattices made to date at Hanford. All lattices were water moderated hexagonal arrays loaded with uranium of enrichments up to 3.15.

The Astron, a thermo-nuclear fusion research machine, requires the injection of high-energy electron at 5 MEV emery level +- 1/2 %, 200 amperes, 60 pulses per second, 0.3 usec pulse width. The accelerator will work by the induction principle with approximately 500 magnetic cores, each 1/2 inch thick lined up on centers. Each core will be pulsed by a single primary turn and the electrons forming the secondary will experience a voltage acceleration equivalent to the primary voltage upon passing by each core. The coupling in this arrangement has been tested and it is very nearly unity.

Continued operation of F reactor with high water collection rates during the past 12 years has resulted in numerous detrimental effects. In addition to promoting external corrosion tube leaks, water leaks have corroded the Gunbarrel to the biological shield donut assemblies and cast iron thermal shield blocks, thus preventing the majority of tubes in F reactor from unrestrained thermal expansion. Fatigue of the Van Stone flange under the resulting compression loads leads to eventual failure in some cases. In addition, excessive compression loads exerted against the nozzle gasket result in plastic deformation and eventual failures of the gasket.