The following is taken from ORNL-2257, Instantaneous Velocity Profile Measurement by Photography, by R. E. Lynch, L. D. Palmer, and G. M. Winn. This report is in in preparation status; and errors, inconsistances, and omissions in he language, as well as in the technical aspects, may exist. The technique of using phosphorescent particles to enable photographic determination of qualitative and quantitative instantaneous velocity profiles is covered by AEC Patent Application No. SN-710, 371 issued to F. E. Lynch, L. D. Palmer, H. F. Poppendiek, and G. M. Winn and entitled " A Method of and Means for Visualizing Fluid Flow Patterns.

Uranium extractions from carbonate solutions were effective and phase separation rates were rapid using a new commercial quaternary extractant, Alamine 336. Extraction coefficients were approximately proportional to the quaternary concentration. Addition of -0.5 mole tridecanol/mole quaternary to the solvent gave optimum extraction efficiency and phase separation rates.

Standard water treatment practices have proven adequate for scale and corrosion control on the secondary side of the ORR pool-cooling heat exchanger. Corrosion rates measured on specimens exposed to secondary water showed maximum corrosion rates of approximately 1 mpy during the first exposure period and these rates decreased during subsequent exposure.

A preliminary study of dispersing agents for thorium oxide has been completed and several of the dispersants have possible uses. Also many of the industrial dispersing agents tested are not usable with thorium oxide due to induced behavior causing balling and caking. The effects of nitric acid concentration have been observed to also effect each dispersing agent.

Temperatures are given at which two liquid phases form in a synthetic homogeneous reactor fuel solution and its concentrates. The data show a two-liquid-phase boundary temperature of 332°C for the Particular HRT Fuel composition and a flat minimum temperature of 305°C for the initial solution concentrated between 300 and 329°C are presented to indicate solution stability in this temperature region. Some related comments on current HRT operations are given.

The method of calculation of various quantities relating the temperature and the rate of heat removal of UO2 test elements is presented. Graphs of the appropriate quantities as a function of the rate of heat removal are included.

An improved heat sink for space vehicles was proposed in ORNL-CF-59-1-21. Subsequent work on the problem has indicated that there is a substantial probability of a puncture of such a radiator by meteors. To meet this problem a modified geometry has been evolved for which the probability of a meteor puncture should be reduced by a factor of at least 100 relative to the radiator of the original proposal at the expense of an increase in radiator weight of possibly 30%. This memorandum outlines the approach to the problem and a series of similar promising solutions.

Preliminary measurements of the corrosion of titanium were made in 13 M HNO3-0.05 M fluoride using 0.1 M H3BO3 as a liquid and vapor phase complexing agent. Titanium Ax-55 was attacked at average rates of 0.58 and 0.33 mils/month in the liquid and vapor. In dissolver solutions containing 0.5 and 1.0 M titanium, all rates were less than 0.1 mils/month.

Many elements exhibit anisotropic scattering at energies of interest in reactor calculations. A method is presented for the calculation of transport cross sections including the observed anisotropy.

This memorandum summarizes the results of an analysis to determine the extent of displacement of the EOCR core due to blowdown in case of several postulated hot main gas coolant pipe failures. Results show that the core will be damaged for any hot pipe double-ended failure. Excepting the improbable case of no coolant flow existing proper to the break, the core will be damaged for any hot pipe fracture exposing a total flow area to the atmosphere equal to that of one pipe. Smaller breaks will probably be safe in this respect.

The nil-ductility-transition (NDT) temperature, as defined by the Naval Research Laboratory drop-weight test, was determined on the A212B carbon-silicon steel used in the pressure vessel of the N. S. Savannah nuclear reactor. Correlations were made with the Charpy-V-notch impact energy at NDT. Specimens taken at two different thickness location from materials used in the upper closure head of the reactor vessel yielded NDT temperatures of 0 - 20°F which correspond to Charpy-V-notch impact energies of 11-19 ft-lb. Testing of as-received material used in the lower closure head indicated that the NDT temperature was 50°F which was equivalent to an average Charpy-V-notch impact energy of 12 ft-lb. After normalizing and stress-relieving this material, in order to more closely approximate the final condition of the reactor vessel, NDT was reduced to less than 10°F.

The rate of uranium sorption by a strong-base anion-exchange resin (Dovex 21K) from a uranyl sulfate solution (U 0.005 M, H2SO4 0.02M, SO4 0.2 M) was studied using a stirred vessel technique and measuring the U235 gamma radiation on each bead. Resin initially in the chloride form and the sulfate for was studied.

Preliminary experiments have been conducted to evaluate the use of the nuclear reactions Li6 (n,α)H3 and O16(H13,n)F18 to determine the thickness of oxide films on metals. Sheets of thin paper and of aluminum, imbedded in powdered LiF, were irradiated with pile neutrons at a flux of 6 x 10^11 n/cm^2/sec and counted with an end-window proportional counter. A saturation activity of 1.87 hr F18 of 150 dis/min per microgram of oxygen was observed in the paper, but radioactivity due to impurities masked F18 in the aluminum. It is concluded that a 1 A (0.01 μgm/cm^2) oxide film thickness may be measured by a neutron irradiation at a flux of 10^14 n/cm^2/sec but chemical separation of induced radioactivity from the bulk metal is essential.

A method for determining the concentration of Li6 in aqueous solution has been tested using the nuclear reactions Li6 (n,α)H3 and O16 (H3,n)F18. Annihilation 7 radiation of induced 1.87 hour F18 radioactivity was counted with a well-type scintillation counter, and the radioactivity per millimole of lithium was found to be independent of lithium concentration below about 0.2moles/liter. The sensitivity limit for detecting lithium is less than 0.1 micromole (0.0075 micromole Li6).

In the preliminary stages of getting up a time-of-flight system for measuring neutron spectra from proton reactions, a study of the time dependence of the beam in the 86Inch Cyclotron was made. This study revealed the expected bunching of the protons to produce a short burst of beam on each cycle of the 13.4 Mc/s accelerating voltage. In addition to the 13.4 Mc/s structure, however, there was a 360 c/sec modulation of the beam pulses and a complicated pattern built upon that.

Tests were conducted to determine methods of removing scale deposits from the HRT heat exchangers. A mockup of the heat exchanger header was cleared of a deposit of iron rust by reverse flushing at a flow rate below 75 gpm. A tube bundle consisting of 109 1/4in. O.D. x 0.049 in. wall tubes was plugged with rust. Approximately 80% of these tubes were unplugged by using a 70 psi water pressure differential in combination with vibration from a pneumatic rivet gun. No mechanical method was employed in the tests which could clear the remaining tubes.

The results of a parametric study on a gas cooled reactor are reported on herein. The system considered was a helium cooled, UO2 fueled arrangement with the fuel assemblies consisting of clusters of long cylindrical elements, each element covered b a stainless steel jacket. The axial power distribution was assumed to be a "chopped cosine" having an axial peak-to-average power 1.32.

The preliminary process design of a PRFR pilot leaching plant, which is proposed to be located in Cell B of Building ORNL, is considered. Chemical, physical, and nuclear parameters are investigated in order that the leaching operations may be carried out without any chemical or nuclear hazards.

A series of neutron multiplication measurements with arrays of 1 by 8 by 10 in. slabs of 93.4% U235-enirched uranium metal have been made to provide data from which safety criteria for the storage of these fissile units can be established. Each slab contained 22.9 kg of U235. A maximum of 125 unites was assembled. The arrays studied were cubic lattices of the units and were usually parallelepipedal in shape.

The Turco 4501 process is recommended for the decontamination of the PRFR pilot leaching plant equipment. The caustic-tartrate-nitric acid process is recommended for the decontamination of the cell and the equipment exterior.

Nitrate contained in raffinates from Canadian Blind River mills interferes seriously with thorium extraction by secondary amines. With primary amines, however, the effect is negligible and these compounds are the preferred process extractants.

In connection with the program of the measurement of eta for U233, several critical experiments have been performed by R. Gwin and D. W. Magnuson of ORML with light water solutions of uranyl nitrate (highly enriched in either U233 or U35) in an essentially bare sphere 27 inches in diameter. This report presents the results of two multigroup-diffusion-theory calculations for the above experiments performed by C. B. Mills and associated at Los Alamos. Assumer cross sections, material concentrations detailed neutron balances and a comparison with elementary theory are included. The agreement between the calculated and experimental multiplication constants is excellent for the multigroup calculation but only fair for the elementary calculation. The latter method overestimates the fast leakage so that the computed multiplication constant is less than that found experimentally.

A Lucite model of a multi-stage countercurrent hydroclone solvent extraction apparatus has been constructed and tested with Amsco-water. The diffusivity of Cs 134 tracer in aqueous chloride solution was measured to check the performance of the capillary diffusivity measuring system. The experimental data from four Druhm runs showed that 1/8in. thick graphite liners are usable for reactor temperatures above the boiling point of sodium.

The 300A and loop were operated for 2862 hr with thorium oxide slurry at 1500 psi and 280ºC to determine the effects vane inlet and exit geometries on impeller wear, the wear rate of aluminum oxide bearings in this size pump, and the operating characteristics of the loop. The thoris, a 1600*C-fired oxide, had a mean particle size of approximately 2 u. Average circulating slurry concentration was approximately 450 grams of thorium per kilogram of water and average flow rate was approximately 300 gpm.