In the preliminary stages of getting up a time-of-flight system for measuring neutron spectra from proton reactions, a study of the time dependence of the beam in the 86Inch Cyclotron was made. This study revealed the expected bunching of the protons to produce a short burst of beam on each cycle of the 13.4 Mc/s accelerating voltage. In addition to the 13.4 Mc/s structure, however, there was a 360 c/sec modulation of the beam pulses and a complicated pattern built upon that.

Equilibrium loading of uranium on Dowex 21K has been studied in a sulfate system for uranium concentrations from 0.0005 M to 0.0005 M, total sulfate concentrations of 0.45 M to 0.6M, and sulfuric acid concentration of 0.020 M. Loading data have been fitted to Langmuir adsorption isotherms and Langmuir constants have been evaluated. Resin was equilibrated with uranium feed solutions by flowing the feed through a shallow fixed bed of resin.

Either system appears to be fairly satisfactory from a containment standpoint. Current results indicate probable over-all rates of about 0.2mils/mo for titanium vs. 1.5-3.0 mils/mo for Ni-o-nel. Tests are not 100% comparable due to changes made in flowsheet conditions, but have been of sufficient variation and length as to allow good predictions to be made. Both metals show some tendency toward local attack in Thorex solutions. These tendencies are increased by poor welding techniques.

The Atomic Energy Commission has assigned the Hanford Atomic Products Operation the responsibility of providing the technology and facilities for the interim reprocessing of slightly enriched uranium fuels discharged from power and propulsion reactors. The fuel from the various reactors vary greatly in physical dimensions and in the composition of the core and cladding. For the purposes of chemical reprocessing, the fuels may be divided into the three main categories of aluminum, Zircaloy or stainless steel clad elements. The fuels may be sub-divided by the nature of the core material; e.g. metallic uranium, uranium dioxide, uranium-molybdenum alloys uranium-aluminum alloys, etc.

For purposes of an earlier consideration of the effects of in-reactor test loops on PRTR operation and program, the design of the high pressure, H20 cooled fuel test loop was assumed to be similar to that for the high pressure, gas cooled loop. Detailed design criteria for the H20 loop have recently been completed so that this assumption is no longer necessary. Therefore, to insure that the effects of all proposed in-reactor loops are fully evaluated with respect to Plutonium Recycle Program objectives, the present study has been carried out. Much of the qualitive discussion in the original analysis is still considered valid. Thus, rather than repeating the entire analysis as it pertains to the H20 loop, only those departures resulting from differences between the assumed design and the scope design are presented.

Disposal of liquid radioactive wastes to ground requires knowledge of the area ground-water hydrology. Information is desired on direction and velocity of ground-water flow. Direction of flow can be determined from maps showing contours on the water table surface, such contours being derived from well water elevations. Ground-water velocity is more difficult to ascertain.

In another paper there was reported an attempt to observe the charge-exchange process in a counter-triggered multiplate cloud chamber at the Bevatron but the interpretation was ambiguous. Shortly after the close of that experiment the 30-in. propane bubble chamber at the Lawrence Radiation Laboratory was completed and able to be used for a combined engineering test and experiment. The existence of Reaction (1) has been confirmed in this experiment, and an approximate cross-section value for carbon is calculated.

An experiment was designed utilizing a charge-exchange reaction to study the decay and interactions of the neutral K mesons produced. The experiment produced no events that could be interpreted as either the decay or interaction of neutral K mesons. The nature of the experiment and the possible explanations of this unexpected result are presented in this paper.

This bibliography contains 37 references on self-shielding cross sections. The bibliography is limited to the period from 1951 through November 1959 with the references arranged alphabetically by title. The sources used in compiling this bibliography were: Abstracts of Classified Reports Nuclear Science Abstracts

The apparatus and procedures that are to be used to fill the liquid metal system of the Pratt and Whitney Forced Convection Liquid Metal Inpile Loop are described. The liquid metal to be used is a mixture containing 56% Na and 44% K, which is a liquid at room temperature. In order to simplify the filling procedure at the reactor site, two containers, each of which contains exactly enough liquid metal to fill the experiment to the prescribed level, a fill dolly incorporating a purified helium system, and an evacuation system will be provided at the reactor site. After completion of the liquid metal transfer, the liquid metal fill tube will be crimped, cut, and seal welded. The liquid metal and helium systems will then be pressurized through the helium fill tubes, which will also be crimped, cut, and seal welded. Each tube seal weld will be inspected after completion of the weld by mass spectrometry leak check and dye penetrant fault detection

None

This document details activities of the Fuels Preparation Department during the month of November 1959. (FI)

The objective of the test detailed in this report is to irradiate self-supported fuel elements under conditions of severity comparable in these expected for future loadings of this geometry, to attempt to determine the resistance to corrosion of cooled cladding, the effect of supports on cladding corrosion and coolant flow patterns, and the relative resistance to ``hot-spot`` type attack and rupture of ``projection`` fuel elements and rib supported elements. This test will authorize irradiation of four columns of self-supported and four columns of rib-supported I and E, 1.47% enriched fuel elements until two ruptures are sustained in each group on type demonstrates a significant factor of improvement in rupture resistance over the other.

The Expansion Study Task Force has evaluated several cases of Hanford reactor operation at power levels considerably higher than is presently obtained in the six older reactors. These higher power levels result in more rigorous operating conditions of temperature, heat flux, neutron flux, hydraulics, reactor control, etc. The purpose of this document, the various components of which were prepared by Process and Reactor Development Sub-Section personnel, is to assess the technical feasibility of operation under the proposed conditions, and to delineate those specific areas of development effort which may be necessary to provide adequate support for an expansion program.

For several years, a major category of fuel element failures has been the side corrosion type, characterized by localized accelerated fuel element jacket corrosion. Since it has been demonstrated {sup 1} that misalignment of fuel elements in a process tube will produce flow patterns and accelerated corrosion, termed ``hot spots``, failure to align the fuel elements in process tubes is considered a contributing factor in the production of side corrosion failures. Preliminary testing of both self-supporting and ``bumper`` fuel elements is underway. Data on the self-supporting fuel elements have demonstrated that the bridge-rail projections have sufficient support strength, do not of themselves create a corrosion problem and in actuality probably eliminate any hot-spot areas. Although one tube of bumper fuel elements in KW Reactor {sup 3} has been discharged, data are not as yet available. Potentially, the most sever corrosion conditions exist during the summer months when reactor inlet temperatures are high. It is desirable then, provided bumper fuel elements limit hot- spot corrosion, to evaluate the bumper concept for large scale use possibly by the summer of 1960. To accomplish this, a demonstration loading of the bumper type fuel elements must be underway by about July, 1959. The purpose …

The material covered are R and D, 2000 reactor and metallurgy program (production reactors, N-Reactor). Topics covered include operating schedules and production, fuel, engineering, safety, control, physics, etc.

"This bibliography lists selected articles on beryllium which have appeared in journals received in the library of the Lawrence Radiation Laboratory, Livermore, California and articles, reports, and books which have appeared in the following abstracting services between January, 1958 and August 1959."

The following report presents neutron-flux measurements made with a concentric-cylinder element (Mark II) and includes axial, radial, and peripheral flux distributions.

None

None

None

None

Electron microscopy was used to supplement metallographic studies of bonds between Zircaloy-2 interfaces. Treated surfaces before bonding, and bonded sections made by a variety of techniques were examined. Electron micrographs of belt-abraded surfaces exhibited a consistent fine-scale roughness. Chemically pickled surfaces were nearly smooth regardless of prior treatment. Chemically pickled samples and a zirconium oxide-coated sample pressure bonded at 1500 F and 10,000 psi had pitting at bond lines that could have been due to voids or to contaminant at the interface which etchod out. The pitting was almost completely eliminated in one sample by pressing one hour at 500 F and 350,000 psi. This indicated that the bond-line pitting in these samples was due to voids at the interface. Zircaloy-2 samples pressure bonded after coating with carbon chromium, iron nickel, or tin etched in relief along the bond line, indicating the presence of contaminant at the interface. On the basis of the present investigation, it is proposed that grain growth across the interface in chemically pickled samples may have been inhibited by the presence of a thin contaminant film originally present on the Zircaloy surfaces. However, the poor grain-growth characteristics of chemically pickled samples may also be due in …

None