The preparation of radioactive metallurgical specimens for microscopic examination is one of the responsibilities of the Radiometallurgy Sub-Unit. An abrasive cut-off machine development program, based upon a previous experimental model, was undertaken to provide a method for sectioning of irradiated materials without undue personnel exposure or spread of contamination and finally to provide data for the design of an abrasive cutting unit for use in the work cells in the Radiometallurgy Building. A horizontal-feed type set-off machine, powered by a 7 1/2 hp motor with V-belt drive, has been developed for the submerged sectioning of irradiated uranium and is currently being used successfully to obtain samples for metallurgical, chemical and physical investigations without excessive personnel exposure or spread of radioactive contaminates.

The following document describes data collected from a 14-month period of analyzing crustaceans containing radioactivity. Provided is information based on the change of radioactivity through seasonal changes.

An experiment now in progress should give some accurate information about the thermal neutron absorption cross section of carbon 12. This report outlines and summarizes this experiment and analyzes it to determine the main sources of error and the probably error in the final result.

Summary: A method was found for determining calcium concentrations in TBP process streams in spite of serious interferences bysodium, ferrous, uranyl, sulfate, phosphate, and sulfamate ions as well as by TBP. The precision attainable varied from sample to sample, depending upon its composition. In general, errors of 20% or greater occurred. The smallest determinable amount of calcium was about 10 mg/1.

Five continuous coatings were produced on zirconium coupons using an anodizing technique. These layers appear to be quite adherent and not subject to visible or audible failure caused by flaxion of the basis metal, Their abrasion resistance, though not investigated thoroughly, appears to be moderately good.

The automatic polarograph is ideally suited for the analysis of waste streams for uranium in the Metal Recovery Process, and with modification, it is applicable to other processes, pilot plants, and even to laboratory set ups. The instrument is simple, dependable, and relatively trouble free in operation. It provides an immediate record of the uranium in the waste and, through better control of the process, lower processing costs.

Seven runs were made with the system Penn. Ref. Co. "Supersol" (dispersed) water (continuous) to investigate the effects of pulse frequency, amplitude plate spacing, volume flow ratio, and throughput on backmixing, using the technique of continuous injection of a tracer solution into the packed section. Backmixing was found to be surprisingly insensitive to all the above variables over the range studied with the exception of pulse amplitude and continuous phase flow rate, showing greatest dependence on the later. Backmixing increased with decreasing continuous phase flow rate and increased with pulse amplitude.

Interest has been expressed in continuously monitoring the beta activity of the uranyl nitrate solution pumped to the RCU receiver tank, to facilitate operation at higher flow rates and with younger feeds. A beta scintillation detector has been developed which should make this feasible, and it is proposed that it be tested on stream for this use.

Unanticipated radioactive contamination of the 200 Areas environs was discovered in the latter part of 1947, about 2.5 years after the startup of the Bismuth Phosphate Separation Plants. It was subsequently established that this contamination was due to radioactive particles emanating from the Separation Plants' stacks, and the need for exhaust ventilation air filtration equipment was recognized. Sand filters were installed in the fall of 1948 in the ventilation systems of the B and T Bismuth Phosphate Plants. These filter units essentially eliminated this contamination problem and have performed satisfactorily to the present time.

Observations on sheep representing flocks in Utah adjacent to the Nevada Proving Ground were compared with findings made on experimental sheep exposed to various amounts of radioiodine. The Utah sheep showed no evidence of the radiation damage observed in experimentally treated sheep. Estimations of amounts of radioiodine on vegetation required to cause serious thyroid damage following a contamination event are included.

A laboratory test was performed to determine if a 10% oxalic acid solution could be safely be employed as a substitute to 2% chromic acid plus 5% phosphoric acid for removal of corrosion products from aluminum corrosion samples or slugs.

A continuous gamma-monitoring instrument capable of measuring the activity of the product of the Uranium Recovery plant has been developed and applied under process conditions. It has a detection limit of 15% and a normal range of up 1000% of the activity of natural uranium. Activity measurements made with this instrument have shown good correlation with laboratory determinations and are contributing to improved control of the solvent extraction process.

The corrosion resistance of four types of austenitic stainless steels to Purex process first and second acid concentrator bottoms was determined. Although the compositions of the two solutions were very similar, tests in simulated solutions of both compositions were conducted to strengthen the basis for the conclusions which were to be made.

From summary: The object of the study was to determine if the heavy metal ions within the concentration ranges normally found in pile cooling water were responsible for corrosion of aluminum.

The conventional volumetric micro-determination of phosphate depends upon the precipitation of phosphomolybdate, filtration and washing of the precipitate, and titration with standard base. The method is slow and tedious, subject to many interferences, and is not applicable to samples containing less than 1-2 mg of phosphate. Other weak acid anions, such as carbonate or acetate, interfere in the method. Strong acid anions, such as nitrate, sulfate, and chloride do not interfere.

The decontamination of portable instruments by the Calibration Unit has presented a problem for some time. Most of the contamination is in the 100 to 500 c/m or 500 to 2000 d/m range. Higher levels of contamination can usually be reduced to these levels, but further cleaning proves quite difficult

An analytical method for Cu-64 in reactor effluent has been studied based upon electrodeposition of the active copper with inert copper carrier. A two hour plating time was employed at a current density of 10 ma/sq cm and four volts across the cell. A stainless steel cathode plate was used. Carrier yields of greater than 80% were obtained with a standard deviation of the yield-corrected counting rate as low as 0.24%. Very little, if any contamination by other radioactive elements present was shown by decay curve studies. Self-absorption and self-scatter factors to correct the counting rate were obtained.

In 1949 Barad presented two solutions to the general diffusion equation. Basic in both solutions is the assumption that in very stable atmospheres a point source may be replaced by a vertical area of uniform concentration at a short distance downwind. This vertical area is considered to exist at the distance at which the plume finally "levels-off" and assumes a flat ribbon-like appearance. In addition if the distance over which diffusion takes place is limited to one or two miles and if only the stable atmosphere with its narrow range of eddy sizes is considered, the average diffusion co-efficient (K) has a signficance which it does not have in the case of neutral equilibrium.

For some time, the need has been recognized for an X-ray diffraction unit applicable to studies concerning the crystallographic characteristics of pile irradiated materials. Except for studies involving specimens of low activity, it has been impossible in the past to investigate materials which emit intense beta and gamma radiations. The exact type and degree of irradiation damage to high activity materials has been largely a matter of theoretical conjecture. The object of this report is to describe an X-ray diffraction spectrometer that can be used to collect crystallographic data from irradiated materials.

Some data on the temperature effect in pulse columns are reviewed. New data obtained with the "vibrational" stirrer are reported. The effects on both the dispersion and coalescence and the net rate of extraction suggest that improved operation of the RA column and lowered waste losses would be expected at elevated temperatures.

The results of electrical resistance measurements have been used as a means of following changes occurring in metals due to irradiation. The electrical conductivity is sensitive to changes in composition and to cold-work or structure damage. In an anisotropic metal, such as uranium, the director of measurement also influences to some extent the values obtained. For these reasons it is essential to use the same material, and if possible the same piece of material, in comparing the electrical properties before and after irradiation. This report is a description of the measurements made on pieces of the same uranium rod before and after an exposure of approximately 150 MWD/T. The results, while preliminary in nature and dealing only with one sample and exposure level, provide data for which a comparison may be made of the electrical resistivity of irradiated and non-irradiated uranium metal.

The very strong flux gradient in the MTR reflector might be thought to be some cause of worry. However, this gradient will be minimized by the presence of the large block of aluminum, which, because of its small effect on neutrons, will tend to flatten the neutron flux in its vicinity. Advantage should be taken of the shape of the test facility by placing the water hole corner closest to the MTR core. This placement should take best advantage of the flattening potentialities of the slowing-down flux from the test slugs, by placing the nearest (beryllium) moderator on the low flux side of the assembly.

Introduction: "The problem of determining the properties and necessary controls on the TBP Plant waste disposal to eliminate transport line plugging and to permit higher concentration prior to return of this to the tank farms was studied. A report of preliminary findings was made to L. W. Finsh on January 31, 1953. This report compiles information in the aforementioned report and findings since its issuance. Previous studies related to this problem are summarized in the U. R. Technical Manual, HW-19140."

In connection with different seals for C & D equipment it appears advantageous that many parts could be made of rubber or other elastic polymers. However, data on the deterioration rate of these materials under irradiation are somewhat scant in the available literature. It appears that for neutrons and pure gamma radiation that a good grade of natural rubber stands up best in all the test reported and because the results of the neutron irradiation are so closely correlated with results from gamma it has been proposed that the principal source of damage is caused by secondary irradiation generated within the rubber by the neutrons.