On October 7, 8, and 9, 1953, the Atomic Energy Commission Division of Reactor Development held a reactor information meeting at the Argonne National Laboratory. The objective of the meeting was exchange of information among people actively concerned with the design of reactors for power to the end that the power reactor program would move more speedily and more economically to another milestone of success. In this volume all the papers presented at the meeting are listed. Copies are given of those papers which are available, and references to published reports are indicated where know for those papers not included in this collections. In order to facilitate handling, this volume is being issued in six parts: Part I Power Reactors; Part II Reactor Physics. Critical and Exponential Experiments Measurements; Part III Reactor Components. Reactor Economics Considerations. Reactor Safeguard and Control; Part IV Fuel Element Design and Problems. Corrosion and Chemistry; Part V Heat Transfer; Part VI Processing. The Author Index is being bound and distributed with Part I of this volume.

Water corrosion tests on mechanically jacketed and pinholed thorium slugs show that these slugs fail in a manner similar to that observed for mechanically jacketed and tested uranium slugs. The proposed mechanism for the water corrosion of these jacketed slugs is analogous to the water corrosion mechanism of jacketed uranium slugs presented in the project lecture. A bare thorium slug appeared to be more resistant to corrosion by water than a mechanically jacketed slug during the first half of the autoclave test. After approximately 90 hours of testing both the bare and the mechanically jacketed thorium slugs were severely corroded by water.

The cup assembly of the Experimental Breeder Reactor (EBR) consists of blanket bricks, inner rings, and safety plug, all of natural uranium. The design of the finish machined brick is shown in Figure 1. These pie shaped bricks when stacked together, 12 bricks arranged in circular form and stacked seven rings high, comprise the cylindrical portion of the outer blanket, 17.875" I.D. x 30.875" O.D. after machining and canning. The inner ring, which is shown in Figure 2, fits inside the bottom layer of bricks. The circular opening in the center of the inner ring is closed by the safety plug shown in Figure 3.

Dissolution of the large number of samples obtained from the natural uranium blanket of the Experimental Breeder Reactor after approximately 485,000 kw.-hr. of operation has been completed, and analysis of these samples for uranium consumed and plutonium formed is well along. An attempt is being made to distinguish quantitatively between uranium-238 and uranium-235 fission in the blanket area by determining the ratio of ruthenium-106 to cesium-137 in the fission products.

Report describing the research and development activities related to nuclear chemistry and radiochemistry and basic chemistry conducted by the Argonne National Laboratory Chemistry Division, Section C-1.

This report was written by different scientist on various experiments of solid state, physical chemistry, radiochemistry and analytical, and special problems.

This report deals with the (1.1) physical properties of graphite, (1.2) effects of pile irradiation on the properties of graphite, (1.3) effect of irradiation on "ceramic" materials, (1.4) effects of radiation on ice -- the x-ray induced luminescence of ice, (1.5) investigation of color centers and other optical properties of single crystals. (2.1) radiation chemistry of liquids, (2.2) application of mass spectrometry to chemical problems, (2.3) vapor pressure and heat of vaporization of uranium, (3.1) nuclear properties of Zr93 and Nb93m from fission, (3.2) mass distribution in the spontaneous fission of Cm242, (3.3) Upper limit to the lifetimes of the first excited states of Th236, U234, and Pu236, (3.4) on the one-body model of alpha radioactivity, (4.1) spectrographic analysis, (4.2) chemical analysis, (5.1) paramagnetic resonance measurements, and (5.2) the 60-inch cyclotron.

This report deals with the (1.1) physical properties of graphite, (1.2) effects of pile irradiation on the properties of graphite, (1.3) effect of irradiation on "ceramic" materials, (1.4) effects of radiation on ice -- the x-ray induced luminescence of ice, (1.5) investigation of color centers and other optical properties of single crystals. (2.1) radiation chemistry of liquids, (2.2) application of mass spectrometry to chemical problems, (2.3) vapor pressure and heat of vaporization of uranium, (3.1) nuclear properties of Zr93 and Nb93m from fission, (3.2) mass distribution in the spontaneous fission of Cm242, (3.3) Upper limit to the lifetimes of the first excited states of Th236, U234, and Pu236, (3.4) on the one-body model of alpha radioactivity, (4.1) spectrographic analysis, (4.2) chemical analysis, (5.1) paramagnetic resonance measurements, and (5.2) the 60-inch cyclotron.

This report deals with the (1.1) physical properties of graphite, (1.2) effects of pile irradiation on the properties of graphite, (1.3) effect of irradiation on "ceramic" materials, (1.4) exposure and dosage for radiation damage experiments, (1.5) apparatus for the measurement of the thermal conductivity of solids, (1.6) effects of radiation on ice -- the thermoluminescence of ice, (1.7) investigation of color centers and other optical properties of single crystals. (2.1) radiation chemistry of liquids, (3.1) radiochemical investigation of the spontaneous fission of Cm242, (3.2) radiochemical service, (3.3) on the one-body model of alpha, (4.1) spectrographic analysis, (4.2) chemical analysis, (5.1) the 60-inch cyclotron.

In the course of the development at Argonne of high purity uranium metal in ingot form, some questions arose as to the validity of the chemical analyses of some of the impurities (particularly those for carbon, boron, and silicon), with one analytical laboratory reporting concentrations in some instances of an order of magnitude greater than another laboratory. Since the low concentrations of impurities in this material involved, in some cases, the development of modified analytical procedures and standards, it was decided to check these discrepancies by having identically prepared samples analyzed by several AEC and associated laboratories. This report is a compilation of the results obtained.

Corrosion-stability tests have been made in static autoclaves at 500 and 600F on solutions of compounds having high neutron cross sections to evaluate their usefulness for shutdown purposes. The only compound tested which appeared to be completely stable in 600F water was boric acid. Limited corrosion data did not show it to cause excessive corrosion of zirconium or stainless steel.

A plutonium-aluminum alloy containing 4 atom per cent aluminum showed no attack after exposure to purified NaK for one month at 400 C in the absence of any oxide. The same specimen and other plutonium alloys, including pure plutonium, showed marked deterioration in shorter exposure in the presence of oxide films from a welded stainless steel container. Pure uranium was resistant even in the presence of such oxides.

The ZPR-I is a facility to study low power critical assemblies using enriched uranium as fuel, having a light water moderator and an essentially infinite water reflector on all sides. The fuel is held in elements 43" long with a 1" square cross section. Any of these elements may be placed in or removed from any position in the reactor tank. Thus, any desired core configuration may be easily obtained.

This report is a record of experimentation conducted intermittently over a period of two years and directed toward preventing deposition of transport corrosion products on fuel elements and other critical components in high-temperature, circulating water nuclear reactor. It includes the postulated mechanism for deposition, a description of experimental equipment, experimental data, results obtained from the experiments, and recommendations for future study.

An analytical method has been developed for zirconium and fluoride ions in the system resulting from the dissolution of fuel elements in hydrofluoric acid. The method is based on determination of the density and electrical conductivity of the dissolved metal solution.

The development of methods which were successful in producing zirconium Hanford type process tubing by roll forming and inert are welding (He) flat strip to which appropriate rails had ben previously attached by resistance welding is described in this report. Grade 2 drip arc melted crystal bar material was used.

This technical report describes the design and construction of equipment and the development of methods for multiple mold, centrifugal casting of reactor fuel slugs. Advantages of the centrifugal casting method over the conventional fabrication methods were found to be (1) fewer operations, (2) fewer and more easily recovered residues, (3) less expensive equipment, and (4) the production of fuel slugs in shapes and in alloys not well adapted to other methods of manufacture. The method consisted of vacuum melting the alloy in stoppered crucibles and bottom pouring into a spinning rotor carrying 16 radially arranged copper molds. The castings so produced were used without further processing, except for cropping the sprue end to obtain the specified length.

Thermal cycling tests on uranium have shown that the dimensional changes that occur on cycling in the alpha range are directly related to both the texture of the material and its grain size: cold rolled rods generally elongate in the direction of rolling, while the same rods, after a beta-treatment, grow at rates several orders of magnitude lower. This considerable improvement by beta-treatment has been attributed to the texture randomization accompanying the heat-treatment. In the course of this heat-treatment, however, considerable grain growth occurs, which ahs the effect of causing surface roughening on cycling (also referred to as "bumping"); fine grained material generally retains a smooth surface. These observations led to the speculation that the most desirable structure in uranium, from standpoint of dimensional stability, is one that combines both a random texture and a fine grain size. Heat treatment of rolled rod offered no easy method to obtain such a product; powder metallurgical techniques, however, appeared ideally suited for the purpose. To this end, early in 1949, the Sylvania Electric Products Company initiated a program to develop suitable techniques for producing uranium powder compacts having the above-mentioned desired characteristics. Because of the availability of thermal cycling equipment at Argonne, …

The purpose of this work was to study reagents which might be effective in dissolving uranium oxide produced during slug failures in water-cooled reactor systems. An aspect of this problem which has subsequently become of primary importance is the solubility or transportability of the oxide in pure water.

The fuel element to be used in the Savannah River reactors is a natural uranium slug 1.00 in. in diameter and 8 in. long, encased in a 2S aluminum can 1.080 in. O.D. having a wall thickness of 0.035 in. The slug is bonded to the can with an aluminum silicon alloy, using the Hanford Al-Si process.

Corrosion rates of present reactor grade uranium were measured in boiling distilled water and were found to have higher values almost by a factor of two then previously reported corrosion rates of uranium. Mallinckrodt biscuit metal showed corrosion rates in the same medium somewhat lower than reactor grade uranium, and high purity metal prepared at Argonne National Laboratory corroded considerably less rapidly than the biscuit metal.

This technical report describes work done on the electrolytic refining of natural uranium in fused salt baths composed of various eutectics of alkali metal chlorides in which were dissolved UF, or UCl3.

Report issued by the Argonne National Laboratory discussing the thermodynamics and electronic distribution of high temperatures. As stated in the introduction, "in the present paper, a model for computing is described which takes into account in detail the interactions between bound electrons and the average interaction of the bound electrons with the free ones" (p. 4). This report includes tables, and illustrations.

Report issued by the Argonne National Laboratory discussing engineering properties of diphenyl. As stated in the abstract, "data collected from the literature on the vapor pressure, enthalpy, liquid density, and vapor density of pure diphenyl are presented. A Mollier diagram, a temperature entropy diagram, and data on viscosity of diphenyl as a function of temperature are also presented" (p. 5). This report includes tables, and illustrations.