Report presenting the results of an investigation to determine the static longitudinal and lateral stability and control characteristics of a model of the Republic MX-1554 airplane at a specified Mach and Reynolds number. No analysis was provided in the paper in order to expedite publication.

Memorandum presenting the application of the nuclear-reactor simulator to an investigation of the validity of the customary assumption of uniform distributions of fuel burnup and fission-product poisoning in a reactor core. The two-group calculation results show the effects of the approximation on the reactivity, power distribution, and xenon-135 distribution for a specific power reactor in which the initial power density varied by a factor of approximately 4 over the core volume.

Report presenting an investigation at transonic speeds to determine the effects of fences, drooped nose, combination fences and drooped nose, and vortex generators on a 45 degree sweptback wing-fuselage combination. The purpose of undertaking this investigation was due to the pitch-up tendency that results from leading-edge vortex-type flow on thin sweptback wings. The data for each component and their interaction with one another is also provided.

Report presenting an investigation of the effects of suction through a porous leading-edge surface in the 19-foot pressure tunnel on a wing with 37 degrees of sweepback of the leading edge, an aspect ratio of 6, taper ratio of 0.5, and NACA 64(sub 1)-212 airfoil sections normal to the 27-percent-chord line. Results regarding the wing without flaps, wing with trailing-edge flaps, and power requirements for porous-leading-edge suction are provided.

Report presenting pressure measurements on a semispan model of a cambered and twisted wing, alone and in combination with a fuselage. The wing had 40 degrees of sweepback, an aspect ratio of 10, a taper ratio of 0.4, and 5 degrees of washout at the tip. Results regarding the pressure distribution and flow separation, section characteristics, and span loading characteristics are provided.

Report presenting flight tests conducted on two different inlet configurations, a submerged divergent-wall inlet and scoop inlet, to determine their characteristics when installed on a YF-93 airplane. Measurements were made of the pressure-recovery characteristics of the inlets and overall airplane drag for each configuration. Results regarding the induction-system efficiency, airplane drag, and a relative comparison of the inlet installations are provided.

Report presenting some measurements of the dynamic lateral stability and lateral and longitudinal trim of a Douglas D-558-II in flights up to a Mach number of 1.87 and an altitude of about 67,000 feet. Testing indicated that the airplane flying in low density air at supersonic speeds had poor dynamic lateral stability, which worsened as the Mach number was increased to 1.85.

Report presenting time histories of rolling and yawing moments on inclined bodies of revolution with vertical-tail surfaces at several Mach numbers and Reynolds numbers. Three ogival-nose bodies with three overall fineness ratios and a conical-nosed body with a fineness ratio of 12.0 were tested. Results regarding the visual-flow studies, rolling- and yawing-moment measurements, and pressure measurements are provided.

From Summary: "An analytical investigation was made to determine from component performance characteristics the effect of air bleed at the compressor outlet on the acceleration characteristics of a typical high-pressure-ratio single-spool turbojet engine. Consideration of several operating lines on the compressor performance map with two turbine-inlet temperatures showed that for a minimum acceleration time the turbine-inlet temperature should be the maximum allowable, and the operating line on the compressor map should be as close to the surge region as possible throughout the speed range. Operation along such a line would require a continuously varying bleed area."

Preliminary results at high speeds indicate lower bearing temperatures, less internal bearing wear, and greater reliability of the conventional, cage-type cylindrical roller bearings than of either full-complement or special cageless roller bearings of the types investigated, although the latter bearing types have been operated successfully to DN values of 1.0 X 10 superscript 6.

Report presenting a theoretical investigation of the lateral stability of a towed high-speed fighter plane using a fighter cruising at supersonic speed at 50,000 feet and a 1000-foot cable. The motion of this configuration was shown to have highly unstable oscillation caused by the towline restraint, but the configuration can be stabilized by choosing the right position for the towline connection and several types of automatic controls.

Memorandum presenting an investigation of the effects of longitudinal location of the wing and varying body size on the interference characteristics of a 45 degree sweptback wing over a range of Mach numbers and angles of attack. The wing had an aspect ratio of 4, a taper ratio of 0.6, and NACA 65A006 airfoil sections. The results indicated that the zero-lift drag of the wing with interference in the forward position was lower throughout the Mach number range than for the wing with interference in the rearward position.

From Summary: "An analysis was made to permit the calculation of the effectiveness of oxide coatings in retarding the transient heat flow into turbine blades when the combustion gas temperature of a turbojet engine is suddenly changed. The analysis is checked with experimental data obtained from a turbojet engine whose blades were coated with two different coating materials (silicon dioxide and boric oxide) by adding silicone oil and tributyl borate to the engine fuel. The very thin coatings (approximately 0.001 in.) that formed on the blades produced a negligible effect on the turbine-blade transient temperature response. With the analysis discussed here, it was possible to predict the turbine rotor-blade temperature response with a maximum error of 40 F."

Report presenting an investigation to determine the effect of oxygen concentration of the inlet oxygen-nitrogen mixture on the combustion efficiency of a J33 single combustor operating with gaseous propane fuel. Combustion efficiency data were obtained at a variety of combustion-inlet total pressures, fuel flow rates, and inlet oxygen concentrations. Results regarding combustor data, application of fundamental combustion properties to combustor data, application of simplified reaction kinetics equation to combustor data, comparison of liquid and gaseous fuel data, and limitations of correlation parameters.

Report presenting a lateral-control investigation in the 19-foot pressure tunnel of an unswept wing with 6-percent-thick hexagonal airfoil sections, aspect ratio 4.0, and taper ratio 0.625. The wing was mounted on a circular fuselage with a fineness ratio of 10 to 1.

Report presenting a flight investigation to determine the drag and stability at low lift coefficients of models of a modified-delta-wing airplane at a range of Mach and Reynolds numbers. A summary of the drag and stability data from the tests is provided.

The results of transonic flight measurements of the longitudinal stability characteristics of the Douglas D-558-II research airplane in the original configuration and with outboard fences mounted on the wings are presented. The levels of normal-force coefficient at which the stability decreases and pitch-up starts have been determined for both airplane configurations at Mach numbers up to about 0.94.

Report presenting an investigation of the effects of heat transfer on boundary-layer transition at higher Reynolds numbers, greater amounts of heating, and a more extensive study of the effects of surface irregularities than what was published in a previous report. Report presenting tests with a smooth model and tests with surface roughness and tunnel flow disturbance are provided.

"This report presents the results of a wind-tunnel investigation of a 1/15-scale model of the Republic MX-1554 airplane at Mach numbers of 1.45 and 1.90 and at a Reynolds number of 3.0 million based on the mean aerodynamic chord of the wing. Tests were conducted to determine the static longitudinal and lateral stability of the model and the control effectiveness of the all-movable tail, elevators, rudder, aileron, and spoiler. All the results of this investigation are presented in graphic form and, in addition, the basic data have been cross-plotted to show the angle of attack, control deflection, and drag coefficient for the model balanced by the movable tail or the elevators" (p. 1).

"The influence of triangular-shaped end plates on the lift and the flow field of a canard-type control surface mounted on a symmetrical fuselage was investigated in the Lewis 8- by 6-foot supersonic wind tunnel at a Mach number of 2.00, body angle of attack of 2 degrees, and control-surface deflection angles of 3 degrees, 6 degrees, 8 degrees, and 10 degrees. The investigation demonstrated that the addition of end plates to a canard-type control surface increased its lift and rearranged the single vortex into a two-vortex system. Perforating the end plates reduced these effects and resulted in a decrease in lift and a change in the flow-field characteristics" (p. 1).

From Summary: "Flat, plate-type elements, 3.5 by 0.5 by 0.070 inches in size and containing 10 percent elemental natural uranium, were produced by hot pressing. The elements were acid-treated to remove surface uranium and then coated with an alumina glaze. Such an element remained stable and did not lose detectable quantities of fission fragments in a 400-hour treatment at 1800 degrees F in a flux of 5 X 10 to the 11th power neutrons per square centimeter per second. Such elements are conveniently produced and, dependent on design and on the successful resolution of problems such as thermal shock, offer a possible method of increasing air-cycle element temperatures and related performance."

"The over-all performance of a 16-stage axial-flow compressor was determined with various stator-blade resettings and a reduction in solidity of the rotor blades in the last three stages. It was shown that little control over the sudden change in slope of the surge-limit line at intermediate speeds was obtained with the blade modifications attempted, except that some change in speed at which the change in slope occurred could be effected by stator-blade resettings" (p. 1).

Report presenting experimental damping-in-roll derivatives obtained for a series of 33 swept and tapered wings. The wing plan forms were selected so that a range of leading-edge positions ahead of and behind the Mach cone obtained at three Mach numbers.

Report presenting testing of a ram-jet canard missile model with a wing and horizontal and vertical canard surfaces of delta plan form with 70 degree swept leading edges in the supersonic pressure tunnel. Two ram-jet nacelles were mounted in the vertical plane near the rear of the body and various combinations of components were tested. Results regarding the longitudinal and lateral characteristics, comparison with theory, and effect of nacelles on the model are presented.