Report presenting the boundary-layer and stalling characteristics on an NACA 64A006 airfoil section at a Reynolds number of 5,800,000. Data included measurements of lift, drag, and pitching moment, chordwise distributions of pressure, visual studies of the boundary-layer flow, and surveys of the static-pressure and velocity distribution within the boundary layer. Results regarding force and moment characteristics, pressure distributions, and boundary-layer characteristics are provided.

"A solution is presented for the problem of the buckling of curved rectangular panels subjected to combined shear and direct axial stress. Charts giving theoretical critical combinations of shear and direct axial stress are presented for panels having five different length-width ratios. Because the actual critical compressive stress of rectangular panels having substantial curvature is known to be much lower than the theoretical value, a semiempirical method of analysis of curved panels subjected to combined shear and direct axial stress is presented for use in design" (p. 1).

Report presenting the results of an experimental investigation to determine the pressure-recovery and mass-flow characteristics of single and twin NACA submerged intakes on the sides of a fuselage at various angles of sideslip. Tests were conducted with single and twin submerged intakes on a model of a fighter-type airplane.

"There has been under development for the high-speed wind tunnel of the LFA an optical measuring arrangement for the qualitative and quantitative investigation of flow. By the use of interference measurements, the determination of density at the surface of the bodies being tested in the air stream and in the vicinity of these bodies can be undertaken. The results obtained so far in the simple preliminary investigations show that it is possible, even at a low Reynolds number, to obtain the density field in the neighborhood of a test body by optical means" (p. 1).

Results are presented for the moments and position of force centers of a series of cambered round bodies derived from a torpedo-like body of revolution. The effects of placing fins on the rear of the body of revolution are also included.

Report presenting six numerical examples for steady, two-dimensional, compressible, nonviscous flow in centrifugal compressors with straight blades, the center lines of which generate a right circular cone when rotated about the axis of the compressors. A seventh example is presented for incompressible flow. Correlation equations are developed whereby the flow conditions in any impeller with straight blades can be determined for all operating conditions.

"As part of the performance investigation of compressors for the J33 turbojet engine, the A-21 model and the A-23 model with a 17- and a 34-blade impeller were operated with water injection at their respective design equivalent speeds of 11,500 and 11,750 rpm. Inlet conditions of pressure of 14 inches of mercury absolute and of ambient temperature correspond to those of the investigation of these models without water injection. The water-air ratio by weight ranged from 0.05 to 0.06. By the use of water injection, the peak pressure ratio of the A-21 compressor and the A-23 compressor with a 34-blade impeller increased approximately 0.38, whereas that of the A-23 compressor with a 17-blade impeller increased only 0.14" (p. 1).

Report presenting aerodynamic and icing investigations in the icing research tunnel on a model of a turbojet-engine nacelle with a short straight air inlet. The hot-gas blowback system consisted of several orifices peripherally located around the inlet and was investigated in both dry-air and icing conditions. Results regarding the aerodynamic investigation without bleedback, aerodynamic investigation with cold-gas bleedback, aerodynamic investigation with hot-gas bleedback, and icing with bleedback are provided.

"Abrupt rudder-fixed aileron rolls have been made with the Bell X-1 airplane in powered flight at Mach numbers between 0.90 and 1.06 at about 40,000 feet pressure altitude. These aileron rolls indicate that the aileron effectiveness for large deflections at Mach number 0.94 is only one-fourth the value at Mach number 0.82, and the effectiveness at Mach number 1.06 is slightly greater than at Mach number 0.94" (p. 1).

Ignition studies of flowing gases were made to obtain information applicable to ignition problems in gas-turbine and ram-jet aircraft propulsion systems operating at altitude conditions.Spark energies required for ignition of a flowing propane-air mixture were determined for pressure of 2 to 4 inches mercury absolute, gas velocities of 5.0 to 54.2 feet per second, fuel-air ratios of 0.0607 to 0.1245, and spark durations of 1.5 to 24,400 microseconds. The results showed that at a pressure of 3 inches mercury absolute the minimum energy required for ignition occurred at fuel-air ratios of 0.08 to 0.095. The energy required for ignition increased almost linearly with increasing gas velocity. Shortening the spark duration from approximately 25,000 to 125 microseconds decreased the amount of energy required for ignition. A spark produced by the discharge of a condenser directly into the spark gap and having a duration of 1.5 microseconds required ignition energies larger than most of the long-duration sparks.

"NACA instrumentation has been installed in the Northrop X-4 airplane to obtain stability and control data during the Northrop conducted acceptance tests. The results of the fourth and fifth flights of the Northrop X-4 number 1 airplane are presented in this paper. These data were obtained for a center-of-gravity position of approximately 19.5 percent of the mean aerodynamic chord. The results of this flight showed that the directional stability as measured in steadily increasing sideslips was positive and high and that the effective dihedral was positive. The results also show the airplane to be longitudinally stable, stick fixed, with the center of gravity at 19.5 percent of the mean aerodynamic chord" (p. 1).

Report presenting an approximate method for calculating the interference pressure distribution at zero lift of a symmetrical sweptback wing mounted on a circular cylindrical body with the chord plane of the wing passing through the axis of the body. An example is provided using a circular cylindrical body and an untapered wing with 60 degrees of sweepback.

"Available information on gust structure, airplane reactions, and pertinent operating statistics has been examined. This report attempts to coordinate this information with reference to the prediction of gust loads on airplanes. The material covered represents research up to October 1947" (p. 807).

From Introduction: "An analysis of eddy currents in a compressor blade, the geometry of which has been limited to that of a flat plate for simplicity, is presented."

Report presenting an investigation to determine the damping-in-roll characteristics of a 42.7 degree sweptback wing using a linearly twisted wing to represent a rolling wing. Results regarding the effect of the airfoil contour, damping-in-roll coefficient, wing-tip helix angle, and theoretical results are provided.

Results of previous model ditching tests of the Lockheed Constellation airplane are reported. Further model tests have been made to determine the probable ditching characteristics and the proper ditching technique for the airplane with the Speedpak attached. This paper presents the results of these tests. Design information was furnished by the Lockheed Aircraft Corporation. A three-vies drawing of the airplane with the Speedpak attached is shown. The tests were made in calm water at the Langley tank no.2 monorail.

Report discussing an investigation to determine the effect of sweepback on the static and rolling stability derivatives of a series of wings with a taper ratio of 0.6 and an aspect ratio of 4. The influence on the straight-flow characteristics, rolling-flow characteristics, and aileron characteristics are provided.

A model of a Consolidated Vultee Aircraft Corporation Skate 7 sea-plane was tested in Langley tank no. 2. Resistance data, spray photographs, and underwater photographs are given in this report without discussion.

Report presenting an analysis of the dynamic-lateral-stability characteristics of the Bell X-2 airplane as affected by variations in mass, aerodynamic, and dimensional parameters by means of calculations of the period and rate of damping of the lateral oscillation. Results regarding the airplane with flaps and gear retracted, airplane with flaps and gear lowered, and effects of assumed modifications to the airplane are provided.

Report presenting an investigation of a series of flame holders designed with the objective of providing a high combustion efficiency in a ramjet combustor at an inlet air velocity of 200 feet per second, inlet-air pressure of 60 inches of mercury absolute, inlet air temperature of 200 degrees Fahrenheit, and near stoichiometric fuel-air ratio. Results regarding the preliminary experiments, two parallel rows of gutters, three rows of gutters, staggered gutters, simultaneous use of three rows and staggered gutters, use of molybdenum, and magnitude of pressure fluctuations are provided.

Report presenting the results of flight tests showing lateral oscillation in the Bell X-1 and calculations created to determine the effects of changes in several mass and aerodynamic parameters on the lateral oscillations. Calculations indicate that lateral stability should be improved by a more positive inclination of the principal axis of inertia or a reduction of the value of yawing moment of inertia.

Memorandum presenting measurements made in the transonic speed ranges of the static-pressure position error at a distance of 0.96 chord ahead of the wing tip of both the 8-percent-thick-wing and the 10-percent-thick-wing X-1 airplanes, and at a point 0.6 maximum fuselage diameter ahead of the fuselage nose of the X-1 airplanes. Results regarding the accuracy of pitot-static heads, static-pressure error of wing-tip installation, static-pressure error of the fuselage-nose installation, and error in total pressure are provided.

A supplementary investigation on the stabilization of the Jettisonable nose section of the X-2 airplane has been conducted in the Langley 20-foot free-spinning tunnel. It was found that the nose section could be stabilized by the addition of curved fins which could be folded against the fuselage for normal flight.

Report presenting wind-tunnel testing to determine the independent effects of Mach and Reynolds numbers on the aerodynamic characteristics of a wing-fuselage combination with a wing with the leading edge swept back 63 degrees and with camber and twist. Results regarding the fuselage alone and the effects of camber and twist are also provided.