Report presenting an investigation at a Reynolds number of 6,800,000 to determine the low-speed lateral control characteristics of a 20-percent-chord half-span outboard aileron on a wing with 42 degrees of sweepback at the leading edge. The lateral control, aileron hinge-moment, aileron load, and balance-chamber-pressure characteristics were determined for the wing with and without high-lift and stall-control devices for an angle-of-attack range from -4 degrees through the stall.

"A flight test of the Aero jet Engineering Corporation's 7KS-6000 T-27 Jato rocket motor was conducted at the Langley Pilotless Aircraft Research Station at Wallops Island, Va, to determine the flight performance characteristics of the motor. The flight test imposed an absolute longitudinal acceleration of 9.8 g upon the rocket motor at 2.8 seconds after launching. The total impulse developed by the motor was 43,400 pound-seconds, and the thrusting time was 7.58 seconds" (p. 1).

Report presenting a wind-tunnel investigation of two NACA 7-series type airfoils, one with 17.7-percent chord thickness and one with 15.4-percent chord thickness, each quipped with a 30-percent-airfoil-chord double slotted flap, a slot-lip aileron, and a trailing-edge Frise aileron with two amounts of overhang balance. Measurements of airfoil lift and drag, Frise aileron hinge moment, and slot-lip aileron hinge moment were obtained through a large range of deflection of flap, Frise aileron, and slot-lip aileron and section angle of attack. Satisfactory lateral control can be obtained by using this combination of airfoils, flaps, and ailerons.

Report presenting the damping-in-roll coefficients for a series of thin triangular plan-form wings and two rectangular wings in the 9-inch supersonic wind tunnel. The damping in roll of the rectangular wings was very close to what was predicted by linear theory, but the triangular wings gave results approximately 10 percent below that predicted when the wing leading edges were well ahead of or behind the Mach cone.

Memorandum presenting an investigation of a typical inlet stage of a multistage axial-flow compressor that was designed on the basis of an analysis of basic design variables. The stage, consisting of 19 rotor blades and 20 stator blades with 40 inlet guide vanes, had a hub-to-tip-radius ratio at the rotor inlet of 0.50 and a rotor-blade outside diameter of 14 inches. Results regarding the overall compressor performance, comparison of compressor performance with design, and rotor-row performance are provided.

Report presenting aerodynamic and icing investigations conducted in the icing research tunnel on a model of a turbojet-engine nacelle with a long straight air inlet in order to provide basic design criteria for hot-gas blowback systems. The most uniform temperature distribution was obtained with a bleedback of 4.4 percent at a gas temperature of 1000 degrees Fahrenheit and resulted in an average dry-air-temperature rise of 46 degrees Fahrenheit.

Report presenting free-flight investigations conducted on four 16-inch-diameter ramjet units to determine the performance at high subsonic and supersonic velocities. Data for evaluating the performance were obtained from radio-telemetering and radar-tracking equipment. Results regarding combustion performance, diffuser total-pressure recovery, thrust coefficient, and external drag coefficient are provided.

From Summary: "An investigation has been conducted with the Langley helicopter tower to obtain basic performance and control characteristics of the Raman rotor system. Blade-pitch control is obtained in this configuration by utilizing an auxiliary flap to twist the blades. Rotor thrust and power required were measured for the hovering condition and over a range of wind velocities from 0 to 30 miles per hour. The control characteristics and the transient response of the rotor to various control movements were also measured."

Report presenting an investigation of the effect of hull length-beam ratio on the hydrodynamic characteristics of flying boats that extend to a length-beam ratio of 20. The results are compared with flying boats having a length-beam ratio of 15. Results regarding longitudinal stability, spray characteristics, take-off performance, taxiing and take-off behavior in waves, landing behavior in waves, and a summary chart are provided.

Report presenting a preliminary theoretical and experimental investigation of the supersonic characteristics of blunt-trailing-edge airfoils. Results regarding the drag measurements at zero lift, measurements at angle of attack, and a general discussion of the theoretical and experimental results is provided.

Report presenting an experimental investigation of a submerged air inlet incorporating a cascade of airfoils for turning and diffusing the entering air. Variables associated with submerged air inlets and airfoil-cascade designs were considered, including changes to the ramp plan form and angle for the submerged inlet and the cascade-axis inclination, cascade-blade angle, solidity, and inclination of the center line of the duct for the cascade.

From Summary: "Measurements of wing and fuselage pressure distributions were made at low and high subsonic Much numbers on a 0.16-scale model of the projected MX-656 research airplane. The MX-656 is a supersonic design utilizing a low-aspect-ratio wing and tail. Pressure-distribution measurements indicated that, although the critical Mach number of the wing was approximately 0.81 at 0 degree angle of attack, compressibility effects were of little significance below a Mach number of at least 0.90. The principal effect of compressibility was an increase in the pressure gradient over the after 30 percent of the wing chord, causing a tendency for the flow to separate."

Report presenting an investigation of a model of the Kingfisher XAUM-2 flying torpedo to determine the pressure recoveries within the jet engine nacelle and to determine the effects of several changes in model configuration on the aerodynamic characteristics of the model. The effectiveness of elevons and tabs as control devices was also investigated.

Report presenting a wind-tunnel investigation of a semispan pointed wing of aspect ratio 1.7 with 60 degree leading-edge sweepback and 30 degree trailing-edge sweepforward with a control surface. The purpose of the investigation was to determine the effectiveness of flap-type controls at transonic and supersonic speeds. Results regarding the wing characteristics and control-surface characteristics are provided.

Report presenting a wind-tunnel investigation of a semispan delta wing with the leading-edge swept back 60 degrees. A half-delta control surface was used and testing was performed with and without fences. Results regarding the rolling effectiveness, wing characteristics, and control-surface characteristics are provided.

Report presenting an experimental study of the pressure fluctuations at the combustion-chamber inlets of a ramjet operating a Mach number of 1.92 in the supersonic tunnel. Results are presented for two burner configurations of different operating characteristics to indicate trends in pressure magnitude, frequency, and wave form. Results regarding the perforated conical flame holder, regenerative-type burner, and diffuser total-pressure recovery are provided.

From Summary: "An investigation of turbojet-engine thrust augmentation by means of tail-pipe burning has been conducted in the NACA Lewis altitude wind tunnel. Several fuel systems and flame holders were investigated in a 29-inch-diameter tail-pipe burner to determine the effect of fuel distribution and flame-holder design on tail-pipe-burner performance and operational characteristics over a range of simulated flight conditions. At an altitude of 5000 feet, the type of flame holder used had only a slight effect on the combustion efficiency."

From Introduction: "Data are presented in graphical form to show the engine performance over a range of altitudes from 5000 to 50,000 feet and flight Mach numbers from 0.21 to 0.97. Curves are presented to show the windmilling characteristics of the engine. All engine performance data obtained in the investigation are also presented in tabular form."

"An investigation was conducted with a single combustor from a British Rolls-Royce Nene turbojet engine to determine the altitude performance characteristics of AN-F-58 fuels. Three fuel blends conforming to AN-F-58 specifications were prepared in order to determine the influence of fuel boiling temperatures and aromatic content on combustion efficiencies and altitude operational limits. The performance of the three AN-F-58 fuels was compared in the range of altitudes from sea level to 65,000 feet, engine speeds from 40- to 100- percent normal rated, and flight Mach numbers of 0.0 and 0.6" (p. 1).

Report presenting an analysis to determine the applicability of existing propeller theory and the theory of oscillating airfoils to the problem of determining the magnitude of the forces on propellers in pitch or yaw. The steady-state method for calculating propeller forces appears to give satisfactory results.

Report presenting the results of an experimental investigation to determine the downwash in the region of the trailing vortex behind a trapezoidal-wing tip in a supersonic stream. Results regarding the downwash at spanwise stations, downwash at chordwise stations, and wake survey are provided.

From Introduction: "An analysis of eddy currents in a compressor blade, the geometry of which has been limited to that of a flat plate for simplicity, is presented."

Report presenting tests to determine the recovery of total pressure attainable at a range of Mach numbers, which were performed with models with twin-scoop inlets situated on the sides of a long forebody. Results regarding ducts without slots and ducts with slots are provided.

Report presenting a wind-tunnel investigation to determine the effect of propeller operation on the characteristics of submerged inlets. The tests were performed with a model of a hypothetical fighter airplane powered by a turbine-propeller unit. The propeller had eight blades with thin airfoil shanks and dual rotation and the submerged inlets were placed in the fuselage behind the propeller and forward of the wing.