From Introduction: "Recent investigations have indicated several wing plan forms, wing sections, and wing-body-tail combinations suitable for flight at supersonic speeds. One such lifting surface, a thin, sharp-edged without sweep of aspect ratio 4 and taper ratio 0.5, has been the subject of an investigation in the Ames 12-foot pressure wind tunnel. The aim of the investigation was to determine the aerodynamic characteristics of such a wing plan form throughout the range of subsonic Mach numbers up to 0.94."

Report presenting the performance of a ramjet unit consisting of an intake diffuser, an exhaust nozzle, and a cluster of thin-plate burners contained in a semicircular combustion chamber as investigated in the induction aerodynamics laboratory.

An investigation of the damping-in-roll characteristics of three wings with an aspect ratio of 4, a taper ratio of 0.6, three sweep angles at the quarter chord line, and the NACA 65A006 section as determined through a range of Mach numbers and angles of attack.

Report presenting an investigation using a single combustor from a 4600-pound-thrust turbojet engine to determine the amount of carbon deposition of AN-F-58 fuels and the effect of carbon formations in the combustor on the altitude operational limits. Three fuel blends conforming to AN-F-58 specification were prepared in order to determine the influence of boiling temperature and of aromatic content on carbon deposition. Results regarding carbon deposition and effect of carbon formations on altitude operational limits are provided.

A spin-recovery investigation has been conducted in the Langley 20-foot free-spinning tunnel on a 20-scale model modified to represent the McDonnell XF2H-1 airplane. The project included tests both with tip tanks installed and with the tanks removed. The results indicated that the recovery characteristics of the airplane would be satisfactory for all loadings by normal recovery technique (full reversal of the rudder, followed 1/2 turn later by movement of the elevator down). The rudder pedal and the elevator stick forces likely to be encountered in a spin should be within the capabilities of the pilot.

Report presenting a wind-tunnel investigation to determine the respective variations with Mach number of the static longitudinal stability, the drag, and the effectiveness of a constant-chord control surface for a tailless fighter aircraft with a triangular wing of aspect ratio 2.31.

"A heat-transfer investigation was conducted with air flowing through an electrically heated silicon carbide tube with a rounded entrance, an inside diameter of 3/4 inch, and an effective heat-transfer length of 12 inches over a range of Reynolds numbers up to 300,000 and a range of average inside-tube-wall temperature up to 2500 R. The highest corresponding local outside-tube-wall temperature was 3010 R. Correlation of the heat-transfer data using the conventional Nueselt relation wherein physical properties of the fluid were evaluated at average bulk temperature resulted in a separation of data with tube-wall-temperature level" (p. 1).

A heat-transfer investigation was conducted with air flowing through an electrically heated silicon carbide tube with a rounded entrance, an inside diameter of 3/4 inch, and effective heat-transfer length of 12 inches over a range of Reynolds numbers up to 300,000 and a range of average inside-tube-wall temperatures up to 2500 R. The highest corresponding local outside-tube-wall temperature was 3010 R.

Report discussing the effect of half-span and full-span split flaps through a deflection range on the low-speed, longitudinal characteristics of a sweptback wing with a round-nose, extensible leading-edge flap. Information about the effect of split-flap deflection on lift and stalling characteristics, effect of split flaps on gliding characteristics, and effect of leading-edge roughness on longitudinal stability is presented.

"Abrupt, rudder-fixed aileron rolls have been made with the Bell X-1 airplane having a 10-percent-thick wing in glides to a Mach number of 0.82 at about 30,000 feet pressure altitude. Aileron movements were between one-fourth and one-half of full deflection. These aileron rolls indicate that Mach number has little effect on the aileron effectiveness up to a Mach number of 0.82" (p. 1).

Report presenting an investigation to determine the effects of several leading-edge modifications on the maximum lift and pitching-moment characteristics on a large-scale 45 degree swept-forward wing. A full-span leading-edge flap deflected 30 degrees down tended to give the largest gain of maximum lift. Results regarding the plain leading-edge flaps and cambered nose are explored.

Report presenting an investigation to determine the effect of the primary-jet temperature on the performance of several ejector configurations. The performance of ejectors expressed in terms of the ratio of weight of secondary air flow to primary air flow was found to be affected by temperature in two ways.

"An investigation of the spin and recovery characteristics of a 1/24-scale model of the Grumman XF9F-2 airplane with wing-tip tanks installed has been conducted-in the Langley 20-foot free-spinning tunnel. The effects of control settings and movements on the erect spin and recovery characteristics of the model for a range of possible loadings of the tip tanks were determined. Spin and recovery characteristics without tanks were determined in a previous investigation" (p. 1).

Report presenting an investigation of a family of turbine-rotor-blade designs based on one-dimensional-flow theory and incorporating systematic changes in design variables. They were designed for 40-percent reaction and a total-to-static pressure ratio of 4.00 based on the assumption of constant static pressure along the radius and one-dimensional-flow theory for the design of the rotor-blade passages.

"An investigation was conducted to determine the effect of turbine-disk cooling with air on the efficiency and the power output of the radial-flow turbine from the Turbo Engineering Corporation TT13-18 turbosupercharger. The turbine was operated at a constant range of ratios of turbine-inlet total pressure to turbine-outlet static pressure of 1,5 and 2.0, turbine-inlet total pressure of 30 inches mercury absolute, turbine-inlet total temperature of 12000 to 20000 R, and rotor speeds of 6000 to 22,000 rpm, Over the normal operating range of the turbine, varying the corrected cooling-air weight flow from approximately 0,30 to 0.75 pound per second produced no measurable effect on the corrected turbine shaft horsepower or the turbine shaft adiabatic efficiency" (p. 1).

Report presenting a partial-span wing tested to determine the cause of a flutter which had occurred in high-speed flight. Changes were made to the wing stiffness, location of the center of gravity of the wing, and the mass balance of the aileron. Results regarding the effect of wing changes on flutter, effect of aileron changes on flutter, shock-wave study, and static aerodynamic coefficients are provided.

Report presenting an analysis of the estimated flying qualities of a tailless airplane with the wing quarter-chord line swept back 35 degrees in a range of Mach numbers based on tests of a model of the airplane in the 7- by 10-foot tunnel. Results regarding performance, longitudinal stability and control, and lateral stability and control are provided.

Report presenting the results of a preliminary investigation of a scale model of a convertible-type airplane in the full-scale tunnel. The maximum lift and stalling characteristics of several configurations, the longitudinal stability characteristics, and the effectiveness of the control surfaces with the propellers removed are provided. Results regarding the propulsive characteristics, and effect of propeller operation on the lift and static thrust of the model propellers are also provided.

Report presenting a wind-tunnel investigation through a speed range from Mach number 0.30 to 0.90 to determine the lateral-control characteristics of a 20-percent-chord by 39-percent-semispan aileron and a 60-percent-semispan stepped spoilers on a semispan-wing model with aspect ratio of 3.06 with 51.3 degrees sweepback of the wing leading edge. The aileron rolling effectiveness decreased as the Mach number increased, while the spoiler rolling-moment effectiveness decreased with Mach number.

Report discussing an investigation of two full-scale NACA propellers at a range of blade angles and at speeds of up to 500 miles per hour. The results are compared to previous investigations of five NACA propellers to evaluate the effects of blade-section thickness ratios on propeller characteristics.

Report presenting the results of an experimental investigation of the downwash and wake characteristics behind a triangular plan-form wing in a supersonic stream. Measurements were made of the variation of downwash angle with angle of attack at several positions within the induced flow field. Results regarding the spanwise variation of the induced stream angle, rate of change of downwash at zero lift, variation of downwash with angle of attack, and wake are provided.

"The inlet guide vanes for the supersonic compressor of the XJ55-FF-1 engine were studied as a separate component in order to determine the performance prior to installation in the compressor test rig. Turning angles approached design values, and increased approximately to through the inlet Mach number range from 0.30 to choke. A sharp break in turning angle was experienced when the choke condition was reached" (p. 1).

From Summary: "The performance of the turbine component of a J33 turbojet engine was determined over a range of turbine speeds from 8000 to 11,500 rpm.Turbine-inlet temperature was varied from the minimum required to drive the compressor to a maximum of approximately 2000 degrees R at each of several intermediate turbine speeds. Data are presented that show the horsepower developed by the turbine per pound of gas flow."

Report presenting 1/12-size model of a streamline fuselage modified by patterns of air jets or strips on the fuselage bottom. The effects of spacing of jets, length of jet rows, and direction of jets were determined for a simulated chine configuration. Data are presented on resistance, trim, effective hydrodynamic lift, and spray.