Report presenting testing to obtain experimental confirmation of the effect of air compressibility on cooling and pressure loss of a baffled cylinder barrel and to evaluate various methods of analysis. Testing occurred over a wide range of air flows and density altitudes.

Report presenting an analysis of the power losses in airplane flight of cross-flow plate and tubular intercoolers to determine the cooling-air weight flow and pressure drop that give minimum total power loss for any given cooling effectiveness. The investigation covers a range of flight conditions of altitude, airspeed, lift-drag ratio, supercharger-pressure ratio, and adiabatic efficiency.

Report presenting an investigation of the icing and de-icing characteristics of a Pratt & Whitney R-1830 engine induction system. The current report covers a program to determine the most effective rate and method of injection of de-icing fluid to remove a heavy ice formation from the induction system. Results regarding the flow rates, recovery times, de-icing portions of the runs, and ice formation characteristics are provided.

Report presenting a theoretical investigation of the two-dimensional, incompressible potential flow past a symmetrical lattice of airfoils of arbitrary shape. Expressions are given for evaluation of the velocity and pressure distribution at the airfoil boundary.

Report presenting flight measurements made on a modern pursuit airplane to determine the approximate magnitude of the horizontal tail loads in accelerated flight. Pressures at a few points were used as an index of the tail loads by correlating these pressures with complete pressure-distribution data obtained in the NACA full-scale tunnel.

Report presenting the use of the Ackeret iteration process to obtain higher approximations than that of Prandtl and Glauert for the flow of a compressible fluid past a circular arc profile. The procedure is to expand the velocity potential in a power series of the camber coefficient.

Report presenting the potential function for flow, with circulation, of a compressible fluid about a circular cylinder, which is obtained in series form including terms of the order of M(exp 4) where M is the Mach number of the free stream. The equations are used to obtain pressure coefficient as a function of Mach number at a point on the surface of the cylinder for different values of circulation.

Report presenting equations for calculating the stick-force characteristics obtained with a spring-tab type of elevator control. The main problems encountered in the design of the satisfactory elevator spring tab are to provide stick forces in the desired range, to maintain the force per g sufficiently constant throughout the speed range, to avoid undesirable "feel" of the control in ground handling, and to prevent flutter.

"This report outlines the flight conditions that are usually critical in determining the design of components of an airplane which affect its stability and control characteristics. The wind-tunnel tests necessary to determine the pertinent data for these conditions are indicated, and the methods of computation used to translate these data into characteristics which define the flying qualities of the airplane are illustrated" (p. 1).

Report presenting testing of several designs of nitrided-steel piston rings under variable conditions of output. Testing indicated the importance of good surface finish and conformity of the ring to the bore. Results regarding temperature tests, single-cylinder-engine tests, and multicylinder-engine tests are provided.

Report presenting tunnel-wall corrections for an airfoil of finite thickness and camber in a two-dimensional-flow wind tunnel. The theory takes account of the effects of the wake of the airfoil and of the compressibility of the fluid and is based on the assumption that the chord of the airfoil is small in comparison with the height of the tunnel. The theoretical results are compared with the small amount of low-speed experimental data available and agreement is seen to be satisfactory, even for relatively large values of the chord-height ratio.

Report presenting a method of constructing fins of nearly optimum proportions to the point where a cylinder has been manufactured and tested. Data were obtained on cylinder temperature for a wide range of inlet-manifold pressures, engine speeds, and cooling-pressure differences. Results regarding cooling equations, cylinder-temperature relationships, and a comparison of three cylinder cooling performances are provided.

Report presenting icing tests on a Bendix-Stromberg PD-12F5 carburetor mounted on a Pratt & Whitney R-1830-C4 intermediate rear engine section. Limiting icing conditions were established for simulated cruising power and simulated rated power over a range of carburetor-air temperatures, and relative humidities are provided.

From Introduction: "The purpose of this analysis was to investigate the use of function of intake-manifold temperature and pressure, exhaust back pressure, and engine speed in place of a ventri as a means of measuring engine air consumption and to determine if this function is suitable for automatic mixture control."

In open box beams subjected to torsion, secondary stresses arise owing to lateral bending of the spar caps. The present paper outlines a simple method for estimating the magnitude of these stresses and gives the results of tests of an open box beam in the neighborhood of a discontinuity where the cover changed from the top to the bottom of the box.

Report discusses pressure-distribution tests of a plain flap with interchangeable beveled trailing edges on an NACA 0009 airfoil. The flap chord was 30 percent of the airfoil chord and the bevel chords were 15 and 20 percent of the flap chord. The purpose of these tests was to supply pressure-distribution data that may be used for structural and aerodynamic design of horizontal and vertical tail surfaces.

Report discusses an investigation to determine the aerodynamic section characteristics of an NACA 23021 airfoil with a double slotted flap with a chord 32 percent of the airfoil chord with the flaps at various positions. The maximum section lift coefficient, profile-drag coefficient, flap positioning, and effects of deflecting or removing the lower lip are described.

Report presenting a method for predicting from basic airplane characteristics the elevator deflection required to maintain optimum landing attitude. Charts for evaluating the components of the equation for elevator deflection and a comparison of computed and measured values for 15 airplanes are included. The computed deflection is considered the minimum value required to maintain landing attitude due to variations in piloting technique.

Report presenting testing in the stability tunnel of two types of spring tab used as balances on a partial-span plain aileron. The tabs were connected to a spring located in the control system so that tab deflection was dependent on the control force.

Report re-examining known procedures for handling general resistance testing on flying-boat hull models, with particular attention paid to saving test time and improving the usefulness of the results to designers. While specific testing will likely always be needed, the procedures given in the report for condensing resistance data should make data analysis easier to apply to design.

Report presenting a method of graphical analysis that allows for the prediction of the thermal and aerodynamic performance of a ram-operated heater and duct system, for cabin heating or wing de-icing, at any altitude and airplane speed. Performance can be predicted from the isothermal total pressure drop across the components of the duct system at several ventilating air rates and the thermal output of the heater at various air and exhaust gas rates.

Report describing the behavior of the heat meter when it is used in thermal circuits which are under the influence of transient potentials. Three scenarios are considered: a heat meter suddenly placed on a hot surface, a heat meter mounted on the interior surface of the cabin wall of an uninsulated airplane climbing through air of decreasing temperature, and a heat meter mounted on the interior surface of the composite cabin wall of an airplane climbing through air of decreasing temperature.

Report presenting a determination of the mean effective emissivity as a function of temperature for the surfaces of several metals and insulating materials. A description and discussion of the measuring technique is presented. The results are plotted on a variety of graphs.

Report presenting data on the thermal performance and the static pressure drop characteristics of two finned-type exhaust gas and air heat exchangers. One heater was constructed of copper and stainless steel while the other was constructed from aluminum alloy. The measured thermal outputs and static pressure drops are compared with predicted magnitudes.