From Introduction: "This report presents only that portion of the data from the first ditching which was to be used roughly establish the accelerations experienced by the pilot and the amount of water pressure to which the fuselage structure was subjected during the ditching."

Report presenting testing in the two-dimensional low-turbulence tunnels on a 24-inch-chord model of the NACA 66(215)-116 a = 0.6 airfoil with a 0.25-chord slotted flap. The optimum flap pivot positions were found for three different conditions. The conditions were determined from a consideration of the landing, take-off, and strafing requirements of the airplane.

Report issued by the U.S. Bureau of Mines on the gas injection methods in the oil fields of Illinois. The results and properties of the injections are presented. This report includes tables, graphs, illustrations, and maps.

Technical report with short articles on (1) Uranium-oxygen system compositions UO2 to U3O3; (2) Thorium hydride; (3) Production of cerium; and (4) Production of thorium.

Equations are presented for calculating the stick-force characteristics obtained with a spring-tab type of elevator control. The main problems encountered in the design of a satisfactory elevator spring tab are to provide stick forces in the desired range, to maintain the force per g sufficiently constant throughout the speed range, to avoid undesirable "feel" of the control in ground handling or in flight at low airspeeds, and to prevent flutter. Examples are presented to show the design features of spring tabs required to solve these problems for airplanes of various sizes.

Describes "the tactical employment of the armored infantry battalion, both as part of a larger force, and when acting independently."

Describes the organization, tactics, and techniques of the armored infantry rifle company.

"Axial fatigue tests were made on 189 coupon specimens of 0.032-inch 24S-T aluminum-alloy sheet and a few supplementary specimens of 0.004-inch sheet. The mean load was zero. The specimens were restrained against lateral buckling by lubricated solid guides described in a previous report on this project. About two-thirds of the 0.032-inch specimens were plain coupons nominally free from stress raisers. The remainder contained a 0.1285-inch drilled hole at the center where the reduced section was 0.5 inch wide" (p. 1).

Provides step by step instructions for the erection of prefabricated Army buildings and possible additional units. Provides a list of parts and markings.

Report discusses an investigation into the behavior of a cantilever beam in transverse motion with a mass at its tip when the root is suddenly brought to rest. Equations for determining the stresses, deflections, and accelerations that arise in the beam are also provided. This testing can be applied to the shock created in an airplane when landing and the vibrations that result.

Report presenting a theoretical and experimental investigation of the behavior of a cantilever beam in transverse motion when its root is suddenly brought to rest. The results of both types of investigations are compared.

Report presenting a determination of the effectiveness of a charged condenser for breaking oil foams and to obtain data on which to base the design of such a device for mounting at the oil-tank inlet of an airplane. Results regarding the condenser-plate area and arrangement, wet-plate design, condenser voltage, oil temperature, water in oil, and some safety considerations are provided.

Report presenting a cascade investigation in two-dimensional flow in the 5-inch cascade tunnel and the 1-inch turbine-element testing apparatus to obtain a satisfactory bucket design for use in a modern aircraft turbosupercharger. Results regarding the root sections, pitch sections, and tip sections are provided.

None

From Summary :"A series of charts are presented by which the wing torsional stiffness required to meet a given standard of rolling effectiveness may be quickly determined. The charts may also be used to obtain quickly the aileron reversal speed and the variation of the loss in rolling effectiveness with airspeed. The charts apply to linearly tapered wings and elliptical wings of tubular-shell construction having various aspect ratios with aileron span and location of ailerons as variables. In the derivation of the charts, induced lift effects have been taken into account and the form of the wing-torsional-stiffness curve has been assumed."

This document provides plots of expected rates of heat evolution rates of heat evolution from irradiated metal which may be useful in estimating the cooling water flow required in the the 212 buildings. A comparison of three sources of data found in the Project Handbook is provided. The CN 526 calculations agree very well with the estimates of 16, 32 and 64 days decay periods. CN 526 information was used for calculating the heat evolution rates shown in the following figures, since the data does not cover decay periods under 16 days, and does not include the 93{sup 239} contribution. The expected BTU/Min.(Ton) heat liberation rate vs. cooling time in days for through operating periods is shown. The operating level is taken as 2000 KW/Ton; the BTU/Min.(Ton) liberated may be scaled to higher or lower operating levels by arithmetic ratio. A similar curve in which the cooling water required (GPM/Ton) is substituted for BTU/Min.(Ton) is provided. The metric ton and a water temperature rise of 25{degree}C (45{degree}F) are assumed. The product content of the metal has been substituted for operating level in another plot. The rate of heat evolution is plotted against decay period for various operating times. A base …

Data acquired from the sampling of Columbia River water January 11, 1944, is presented. The water was analyzed for temperature, dissolved oxygen, and iron. The results were compared with results from samples attained from selected taps in the C.M.X. building.

In order to obtain a correlation of drag data from wind-tunnel and flight tests at high Mach numbers, a typical pursuit airplane, with the propeller removed, was tested in flight at Mach numbers up to 0.755, and the results were compared with wind-tunnel tests of a 1/3-scale model of the airplane. The tests results show that the drag characteristics of the test airplane can be predicted with satisfactory accuracy from tests in the Ames 16-foot high-speed wind tunnel of the Ames Aeronautical Laboratory at both high and low Mach numbers. It is considered that this result is not unique with the airplane.

An exact solution and a closely concurring approximate energy solution are given for the buckling of an infinitely long flat plate under combined shear and transverse direct stress with edges elastically restrained against rotation. It was found that an appreciable fraction of the critical stress in pure shear may be applied to the plate without any reduction in the transverse compressive stress necessary to produce buckling. An interaction formula in general use was shown to be decidedly conservative for the range in which it is supposed to apply.

None

Testing of a dynamically similar model of an Army A-20A airplane to determine the best way to land the airplane in calm and rough water and to determine its probable ditching performance. Results regarding the effect of speed and attitude, effect of flap setting, effect of wind and seaway, effect of simulated damage, effect of sinking speed, effect of propellers, effect of gun blisters, and effect of weight are provided.

Report presenting compression tests on six 24S-T aluminum alloy curved sheet-stringer panels 12 inches in length and 24 inches in width, reinforced by six Zeo stringers spaced 4 inches between centers. The increase in developed width had no significant effect on the strain for buckling of sheet between stringers, the strain for buckling of sheet between rivets, the load carried per sheet bay, or the stress at failure.

Report presenting an investigation into the importance of stick force as a criterion of longitudinal stability with special reference to transient effects for maneuvers of short duration. The analysis showed that different combinations of elevator parameters which give the same stick force per unit acceleration in turns give widely different force variations during the entries into and recoveries from steady turns and during maneuvers of short duration such as abrupt pull-ups.

Report discusses the results of testing of rudder deflection for trim at low speeds in the critical wave-off condition. Depending on the lateral center-of-gravity location on the airplane, the useful load in the wings will change and the ability of the rudder to trim the airplane may be greatly improved.