"A procedure which takes into account the aerodynamic span effect is given for the determination of the torsional-divergence velocities of monoplanes. The explicit solutions obtained in several cases indicate that the aerodynamic span effect may increase the divergence velocities found by means of the section-force theory by as much as 17 to 40 percent. It is found that the magnitude of the effect increases with increasing degree of stiffness taper and decreases with increasing degree of chord taper" (p. 1).

Report presenting testing of fifty-eight lightened and five unlightened aluminum-alloy channels as simply supported beams in pure or simple bending produced by loads parallel to the plane of symmetry, and fifty-three lightened and four unlightened aluminum-alloy channels with loads parallel to the back. Four types of testing occurred with various types of support and loading.

Note presenting a least-squares procedure adapted to numerical calculation for the approximate solution of the Prandtl lifting-line equation. Sufficient data are tabulated to permit a solution of the equation by purely numerical methods for an arbitrary symmetrical variation of the chord and the angle of attack.

Report presenting an investigation of the shape of stress-strain curve for a material, especially when the material is subjected to compression, which may cause materials to become unstable at stresses beyond the elastic range. The ratio of stresses to effective modulus is explored in equation form.

Note presenting an effective value of Poisson's ratio for 18:8 Cr-Ni steel computed from values of tensile and torsional moduli of elasticity obtianed in earlier investigations by use of an appropriate formula.

"An empirical equation has been developed that gives the approximate amount of ovalization for tubes under bending loads. Tests were made on tubes in the d/t range from 6 to 14, the latter d/t ratio being in the normal landing gear range. Within the range of the series of tests conducted, the increase in ovalization due to a compression load in combination with a bending load was very small" (p. 1).

From Summary: "The various types of hydrodynamic instability - including porpoising, skipping, and yawing - that may be encountered during take-off or landing of a flying boat are described and the piloting technique required for efficient take-offs and landings is discussed. Suggestions are made for assisting a pilot to become familiar with the take-off and landing qualities of a flying boat that is new to him."

From Summary: "This paper deals with the single problem if circular shell-supported frames subjected to concentrated loadings. A mathematical attack is developed and presented in the form of nondimensional-coefficient curves."

Report presenting a survey of the technical information contained in the literature on the subject of lubrication, friction, and wear of aircraft engine piston rings.

Note presenting fairing compositions applied to aircraft surfaces, welds and junctions of metal plates, and rivet depressions to improve the aerodynamic efficiency of the airplane at high speeds. A method is described for formulating fairing compositions which have, within limits, desired coefficients of thermal expansion. Results regarding water-immersion tests, thermal expansion and softening temperature, temperature-cycle tests, and density are provided.

Note presenting a torsion test to failure for a monocoque box of 24S-T aluminum alloy. The box had a rectangular section and was reinforced by Z-stringers, antirolls, bulkheads, and corner posts.

Report presenting experiments with a flat reinforced sheet model, the longitudinals of which were loaded axially. Two groups of sheets, one with one panel and one with two panels, were cut out and the stress distributions in stringers and sheet was measured with electric strain gages.

Report presenting calibrations in axial tension over the strain range from 0 to 0.0024 are presented for 15 types of single element multistrand wire strain gages. The majority of the gages showed significant differences between the calibration factors for strain increasing and strain decreasing. Improvement in gage performance after preloading was apparent in most cases.

From Summary: "A unit oil system and oil-weighing device designed for laboratory engine tests to permit the remote measurement of oil-flow rate and oil consumption is described. The system regulates the oil pressure and temperature and is closed to make possible the accurate measurement of blow-by gas. The oil is weighed by a self-contained diaphragm and pilot-valve assembly, which uses compressed air as the transmitting medium. Several of those unit systems have given satisfactory service for more than a year."

"Axial fatigue tests were made on 189 coupon specimens of 0.032-inch 24S-T aluminum-alloy sheet and a few supplementary specimens of 0.004-inch sheet. The mean load was zero. The specimens were restrained against lateral buckling by lubricated solid guides described in a previous report on this project. About two-thirds of the 0.032-inch specimens were plain coupons nominally free from stress raisers. The remainder contained a 0.1285-inch drilled hole at the center where the reduced section was 0.5 inch wide" (p. 1).

Note presenting axial fatigue tests made by the resonance method on 10 specimens from airplane wing beams. The specimens contained several types of stress raiser, such as rivets, holes, fittings, splices, reinforcing plates, and so forth. The results show a greater fatigue stress concentration factor for the wing-beam specimens than for drilled coupons machined from the flanges or for parallel strip coupons containing idle rivets.

"A solution of Von Karman's fundamental equations for plates with large deflections is presented for the case of a shear web divided into square panels by reinforcing struts. Numerical solutions are given for struts of infinite rigidity and for struts the weight of which is one-fourth the weight of the sheet. The results are compared with Wagner's diagonal tension theory as extended by Kuhn and by Langhaar. It is found that the diagonal tension theory as developed by Kuhn agrees best with the present paper in the practical range when r=1/4. Kuhn's theory is in especially good agreement for the force in the strut when r=1/4" (p. 1).

"It is well known that the vorticity for any fluid element is constant if the fluid is non-viscous and the change of state of the fluid is isentropic. When a solid body is placed in a uniform stream, the flow far ahead of the body is irrotational. Then if the flow is further assumed to be isentropic, the vorticity will be zero over the whole filed of flow. In other words, the flow is irrotational. For such flow over a solid body, it is shown by Theodorsen that the solid body experiences no resistance" (p. 1).

"A systematic account is given in part I of the use of dimensional analysis in constructing similarity conditions for models and structures. The analysis covers large deflections, buckling, plastic behavior, and materials with nonlinear stress-strain characteristics, as well as the simpler structural problems" (p. 1).

"In the present part I of a series of reports on the inward bulge type buckling of monocoque cylinders the buckling load in combined bending and compression is first derived. Next the reduction in the buckling load because of a nonlinear direct stress distribution is determined. In experiments nonlinearity may result from an inadequate stiffness of the end attachments in actual airplanes from the existence of concentrated loads or cut-outs" (p. 1).

Note presenting an investigation of several laminated glass windshields to determine their suitability for use in airplanes with pressurized cabins. The various constructions of the extended portions of the windshields which serve for mounting purposes included plastic alone, plastic and one sheet of glass extended, plastic extension reinforced with an aluminum strip, and plastic extension reinforced with a steel strip. The results indicated that the laminated windshields with plastic-mounting extensions reinforced by aluminum or steel were resistant to creep and bursting at pressures of the order that will be encountered in service.

Report presenting a note in two parts regarding simplified truss stability criteria. The first part covers the development of simplified criteria for the stability of planar pin-jointed trusses against buckling in the plane of the truss. The second part constitutes a report on tests carried out to verify the validity of the criteria developed in part one.

Report presenting experiments with both curved and flat reinforced sheet models, the longitudinals of which were loaded axially. The stress distribution in longitudinals and sheet was measured with electric strain gages.

This paper is the second part of a series of reports on the inward bulge type buckling of monocoque cylinders. It presents the results of an experimental investigation of buckling in combined bending and compression. In the investigation it was found that the theory developed in part I of the present series predicts the buckling load in combined bending and compression with the same degree of accuracy as the older theory does in pure bending.