From Introduction: "This report presents only that portion of the data from the first ditching which was to be used roughly establish the accelerations experienced by the pilot and the amount of water pressure to which the fuselage structure was subjected during the ditching."

Report presenting measurements of a Consolidated B-24D airplane of accelerations at various points on the wing during landing impacts. landings were made with the wheels initially stationary but free to rotate, with the brakes set before contact, and with the main wheels rotating prior to contact.

Report presenting two low-drag airfoils, the NACA 747A315 and the NACA 747A415, which are designed to have reduced pitching moments about the quarter-chord point and moderately high values of the design lift coefficient and are tested in the tow-dimensional low-turbulence pressure tunnel.

"This report describes tests in the Langley 16-foot high-speed tunnel to determine whether these failures could be attributed to changes in the aerodynamic characteristics of the ailerons at high speeds" (p. 1).

Report presenting tests made in the LMAL 16-foot high-speed tunnel to determine the aerodynamic characteristics of a 1000-pound AN-M-65-AZON radio-controlled bomb at a Mach number range of 0.2 to 0.6. Over the Mach number range, the hinge-moment coefficients, yawing-moment coefficients, and lateral-force coefficients exhibited no important changes with increasing speed.

Report presenting testing in the two-dimensional low-turbulence tunnels on a 24-inch-chord model of the NACA 66(215)-116 a = 0.6 airfoil with a 0.25-chord slotted flap. The optimum flap pivot positions were found for three different conditions. The conditions were determined from a consideration of the landing, take-off, and strafing requirements of the airplane.

From Introduction: "The purpose of this analysis was to investigate the use of function of intake-manifold temperature and pressure, exhaust back pressure, and engine speed in place of a ventri as a means of measuring engine air consumption and to determine if this function is suitable for automatic mixture control."

From Introduction: "The purpose of this analysis was to investigate the use of a function of intake-manifold pressure, exhaust back pressure, intake manifold temperature, and engine speed in place of a venturi as a means of measuring engine air consumption and to determine if this function is suitable for automatic mixture control."

From Introduction: "Certain alternations of a qualitative nature may be performed in spite of the fact that a pressure change cannot be prescribed. It is the purpose of this paper to indicate a method by which qualitative alternation may be performed. It will be noted that the present method of contour modification will serve the intended purpose of the inverse method."

Report presenting 10 practical-construction models of sections of helicopter rotor blades tested in the NACA two-dimensional low-turbulence pressure tunnel at atmospheric pressure. Lift, drag, and pitching-moment characteristics of blades representing the present method of construction of the YR-4A helicopter were determined.

Report presenting an analysis of data on fuel-vapor loss from fuel tanks during simulated flight obtained by six laboratories to show the effects of individual variables such as altitude, initial fuel temperature, rate of climb, booster-pump agitation, fuel depth, fuel-surface area, types of fuel, and vent-line pressure drop on fuel-vapor loss.

From Introduction: "A typical ice formation on a wing leading-edge-type light installation is shown in figure 1. Although the primary purpose of this analytic investigation was to determine the practicability of providing a landing-light thermal ice-prevention system which could be incorporated with the wing leading-edge thermal ice-prevention system of the B-17 F airplane, the analysis has been developed in a general form for future application to similar deigns. "

From Introduction: "The present paper deals with control surfaces having plain-overhang and Frise balances."

From Introduction: "As a part of the general lateral-control investigation by the NACA, the large amount of two- and three-dimensional data on the rolling effectiveness of ailerons without exposed overhang balance is collected and analyzed in the present paper."

From Summary: "This paper deals with the single problem if circular shell-supported frames subjected to concentrated loadings. A mathematical attack is developed and presented in the form of nondimensional-coefficient curves."

Pressure distribution and spray measurements were carried out on rectangular flat and V-bottom planing surfaces. Lift, resistance, and center of pressure data are analyzed and it is shown how these values may be computed for the pure planing procees of a flat or V-bottom suface of arbitrary beam, load and speed, the method being illustrated with the aid of an example.

From Introduction: "The lift increments of different flap arrangements were determined by the method of reference 1 with a simple chord correction factor being applied. This procedure is somewhat similar in basic principles to the method of reference 2. The accuracy of the present method was determined by calculating by means of this method the lift and moment increments of flaps on 10 different finite wing-flap combinations for which wind-tunnel data were available."

"A solution of Von Karman's fundamental equations for plates with large deflections is presented for the case of a shear web divided into square panels by reinforcing struts. Numerical solutions are given for struts of infinite rigidity and for struts the weight of which is one-fourth the weight of the sheet. The results are compared with Wagner's diagonal tension theory as extended by Kuhn and by Langhaar. It is found that the diagonal tension theory as developed by Kuhn agrees best with the present paper in the practical range when r=1/4. Kuhn's theory is in especially good agreement for the force in the strut when r=1/4" (p. 1).

Bulletin presenting an analysis of the vertical-tail loads to be expected as a result of abrupt aileron action in accelerated flight, as in rolls from turns or pull-outs, for example. Critical tail loads may occur in rolling pull-out maneuvers, particularly on airplanes with good ailerons and low directional stability.

From Summary: "The results of an analytical investigation to determine the qualitative effects of elevator-fabric distortion on the stick-force characteristics of an airplane are presented. These results indicate that serious alteration of intended stick-force characteristics can be produced by elevator-fabric distortion."

From Introduction: "Flight tests with electricity heated propeller-blade shoes reported in references 1 and 2 have establish the practicability of protecting propeller blades from ice formations by thermal-electric means."

"A systematic account is given in part I of the use of dimensional analysis in constructing similarity conditions for models and structures. The analysis covers large deflections, buckling, plastic behavior, and materials with nonlinear stress-strain characteristics, as well as the simpler structural problems" (p. 1).

Report presenting equations for calculating the stick-force characteristics obtained with a spring-tab type of elevator control. The main problems encountered in the design of the satisfactory elevator spring tab are to provide stick forces in the desired range, to maintain the force per g sufficiently constant throughout the speed range, to avoid undesirable "feel" of the control in ground handling, and to prevent flutter.

Equations are presented for calculating the stick-force characteristics obtained with a spring-tab type of elevator control. The main problems encountered in the design of a satisfactory elevator spring tab are to provide stick forces in the desired range, to maintain the force per g sufficiently constant throughout the speed range, to avoid undesirable "feel" of the control in ground handling or in flight at low airspeeds, and to prevent flutter. Examples are presented to show the design features of spring tabs required to solve these problems for airplanes of various sizes.