Report discusses the results of testing to determine the maximum rates of control stick (elevator) motion and corresponding maximum stick forces that could be exerted based on experiments with several pilots. The main topics explored were the comparison of the maximum rates of push and pull, maximum rates of push and pull when a mental restriction was placed on the pilot, and maximum rates at which the pilot though he would apply the elevator control forces versus the actual application of forces. Information about experimental procedures and the rig the testing occurred on is included.

Note presenting an investigation of several laminated glass windshields to determine their suitability for use in airplanes with pressurized cabins. The various constructions of the extended portions of the windshields which serve for mounting purposes included plastic alone, plastic and one sheet of glass extended, plastic extension reinforced with an aluminum strip, and plastic extension reinforced with a steel strip. The results indicated that the laminated windshields with plastic-mounting extensions reinforced by aluminum or steel were resistant to creep and bursting at pressures of the order that will be encountered in service.

From Introduction: "As a part of the general lateral-control investigation by the NACA, the large amount of two- and three-dimensional data on the rolling effectiveness of ailerons without exposed overhang balance is collected and analyzed in the present paper."

"The results of a series of tests to determine the effect of internal pressure on the buckling load of a thin cylinder under an applied torque indicated that internal pressure raises the shear buckling stress. The experimental results were analyzed with the aid of previously developed theory and a simple interaction formula was derived" (p. 1).

"Strain surveys were made on the stringers reinforcing a D-section box loaded in torsion and restrained from warping at the root. On the basis of the tests, a procedure is suggested for estimating the bending stresses due to torsion that occur near the flange of a D-section box. A similar test of a triangular-section box showed that for such a section there were no significant bending stresses due to torsion, a fact which was also shown theoretically" (p. 1).

Report presenting an investigation of the cooling of a Franklin 6-AC-29S horizontally opposed cylinder air-cooled engine installed in a Fleetwings model 33 trainer. The cowling on the airplane did not provide satisfactory cooling, but several alterations were tested, including with cylinder baffles. Results regarding engine cooling, aerodynamics of the cowling installation, and predicted versus actual cowling performance are provided.

Numerical methods have been developed for obtaining the steady, adiabatic flow field of a frictionless, perfect gas about arbitrary two-dimensional bodies. The solutions include the subsonic velocity regions, the supersonic velocity regions, and the transition compression shocks, if required. Furthermore, the rotational motion and entropy changes following shocks are taken into account. Extensive use is made of the relaxation method. In this report the details of the methods of solution are emphasized so as to permit others to solve similar problems. Solutions already obtained are mentioned only by way of illustrating the possibilities of the methods described. The methods can be applied directly to wind tunnel and free air tests of arbitrary airfoil shapes at subsonic, sonic, and supersonic speeds.

Report presenting the results of tests of a circular fuselage with various combinations of tail lengths and vertical tail surfaces with and without the horizontal tail surface in the 6- by 6-foot test section of the stability tunnel in the form of diagrams of variation of coefficients of lateral force and yawing moment with angle of yaw and angle of attack.

Field measurements were made on a fighter airplane to determine the approximate magnitude of the horizontal tail loads in accelerated flight. In these flight measurements, pressures at a few points were used as an index of the tail loads by correlating these pressures with complete pressure-distribution data obtained in the NACA full-scale tunnel. In addition, strain gages and motion pictures of tail deflections were used to explore the general nature and order of magnitude of fluctuating tail loads in accelerated stalls.

"Field measurements were made on a fighter airplane to determine the approximate magnitude of the horizontal tail loads in accelerated flight. In these flight measurements, pressures at a few points were used as an index of the tail loads by correlating these pressures with complete pressure-distribution data obtained in the NACA full-scale tunnel. In addition, strain gages and motion pictures of tail deflections were used to explore the general nature and order of magnitude of fluctuating tail loads in accelerated stalls" (p. 351).

Report discusses an analysis and preliminary design of a control linkage that varies automatically with dynamic pressure. The advantages of the device, including greater lateral control than a fixed control linkage without additional aerodynamic balance, are detailed. The effect of variable linkage on lateral-control characteristics is also described.

Report presenting the results of aerodynamic tests of seven-blade propellers which were considered as a possible arrangement to avoid vibration difficulties. Variations of relative blade angle and rotational speeds of the front and rear components of a six-blade dual-rotating propeller were also investigated.

Report discusses the "effects of oil introduced into the combustion chamber and of oil-spray piston cooling on the knock-limited performance of aircraft engines" (from Summary). A CFR engine and Allison V-1710 cylinder were used to test the rate of oil consumption, knock, and knock-limited brake mean effective pressure.

Report presenting an investigation to determine the knock-limited performance in a full-scale aircraft-engine cylinder of leaded blends of 10 pure hydrocarbons and a base fuel.

"A method is presented for predicting the amplitude and frequency, under certain simplifying conditions, of the hunting oscillations of an automatically controlled aircraft with lag in the control system or in the response of the aircraft to the controls. If the steering device is actuated by a simple right-left type of signal, the series of alternating fixed-amplified signals occurring during the hunting may ordinarily be represented by a "square wave." Formulas are given expressing the response to such a variations of signal in terms of the response to a unit signal" (p. 487).

Report presenting a method for predicting the amplitude and frequency, under certain simplifying conditions, of the hunting oscillations of an automatically controlled aircraft with lag in the control system or in response of the aircraft to the controls. Formulas are given expressing the response to a variation of signal in terms of response to a unit signal.

Report discusses measurements of the relaxation time of steam and nitrogen due to their importance as turbine-working fluids. Additional calculations regarding different nozzle lengths are included.

"The effect on static-pressure measurements of locating a pitot-static tube 0.55 chord ahead of an airfoil section has been investigated. The tests were conducted in the NACA 24-inch high-speed tunnel on airfoil sections of various thickness ratios over a large range of Mach number. The results show that for a wing having a thickness ratio of 0.15 the measured Mach number, determined from a pitot-static-tube reading, is approximately 0.01 too low at a stream Mach number of 0.4 and approximately 0.03 too low at a Mach number of 0.8" (p. 1).

"An experimental investigation of rectangular exhaust-gas ejector pumps was conducted to provide data that would serve as a guide to the design of ejector applications for aircraft engines with marginal cooling. The pumping characteristics of rectangular ejectors actuated by the exhaust of a single-cylinder aircraft engine were determined for a range of ejector mixing-section area from 20 to 50 square inches, over-all length from 12 to 42 inches, aspect ratio from 1 to 5, diffusing exit area from 20 to 81 square inches, and exhaust-nozzle aspect ratio from 1 to 42" (p. 161).

Report presenting a device that automatically analyses the data from a 45 degree strain rosette. The rosette strains are properly combined by means of an electric circuit to yield a direct meter reading of maximum shear strain and major and minor principal strains.

From Summary: "Charts are presented for rapidly determining the principal strains and stresses, the maximum shear strain and stress, and the orientation of principal axes from data on 45 degree strain rosettes. The charts may be used for analyzing the conventional data consisting of strains measured along three gage lines 45 degrees apart, but their application is more direct if the rosette data are obtained by means of special circuits that require the use of four gages 45 degrees apart."

From Summary: "The results of an analytical investigation to determine the qualitative effects of elevator-fabric distortion on the stick-force characteristics of an airplane are presented. These results indicate that serious alteration of intended stick-force characteristics can be produced by elevator-fabric distortion."

"The design of curved sheet panels to resist shear involves a consideration of several factors: the buckling resistance of the sheet, the stress at which buckling becomes permanent, and the strength which may be developed beyond the buckling limit by tension-field action. Although some experimental as well as theoretical work has been done on the buckling and tension-field phases of this problem, neither of these types of action appears to be very well understood. This report presents the results of the first series of torsion tests of stiffened circular cylinders to be completed in connection with this study at Aluminum Research Laboratories" (p. 1).

"The effects of changes in aileron rigging between 2 deg up and 2 deg down on the stick forces were determined from wind-tunnel data for a finite-span wing model. These effects were investigated for ailerons deflecting equally in both directions and linearly with stick deflection. Data were analyzed for a Frise, a sealed internally balanced, and a beveled-trailing-edge aileron" (p. 1).