"Tests were run on a single-cylinder and a multicylinder four-stroke engine in order to determine the effect of the dynamics of the inlet system upon indicated mean effective pressure. Tests on the single-cylinder engine were made at various speeds, inlet valve timings, and inlet pipe lengths. These tests indicated that the indicated mean effective pressure could be raised considerably at any one speed by the use of a suitably long inlet pipe" (p. 1).

Report presenting an investigation of the shape of stress-strain curve for a material, especially when the material is subjected to compression, which may cause materials to become unstable at stresses beyond the elastic range. The ratio of stresses to effective modulus is explored in equation form.

Note presenting an effective value of Poisson's ratio for 18:8 Cr-Ni steel computed from values of tensile and torsional moduli of elasticity obtianed in earlier investigations by use of an appropriate formula.

"A procedure which takes into account the aerodynamic span effect is given for the determination of the torsional-divergence velocities of monoplanes. The explicit solutions obtained in several cases indicate that the aerodynamic span effect may increase the divergence velocities found by means of the section-force theory by as much as 17 to 40 percent. It is found that the magnitude of the effect increases with increasing degree of stiffness taper and decreases with increasing degree of chord taper" (p. 1).

Note presenting a least-squares procedure adapted to numerical calculation for the approximate solution of the Prandtl lifting-line equation. Sufficient data are tabulated to permit a solution of the equation by purely numerical methods for an arbitrary symmetrical variation of the chord and the angle of attack.

From Summary: "The various types of hydrodynamic instability - including porpoising, skipping, and yawing - that may be encountered during take-off or landing of a flying boat are described and the piloting technique required for efficient take-offs and landings is discussed. Suggestions are made for assisting a pilot to become familiar with the take-off and landing qualities of a flying boat that is new to him."

Report presenting testing of fifty-eight lightened and five unlightened aluminum-alloy channels as simply supported beams in pure or simple bending produced by loads parallel to the plane of symmetry, and fifty-three lightened and four unlightened aluminum-alloy channels with loads parallel to the back. Four types of testing occurred with various types of support and loading.

"An empirical equation has been developed that gives the approximate amount of ovalization for tubes under bending loads. Tests were made on tubes in the d/t range from 6 to 14, the latter d/t ratio being in the normal landing gear range. Within the range of the series of tests conducted, the increase in ovalization due to a compression load in combination with a bending load was very small" (p. 1).

An investigation was conducted to determine the tensile strength of round-head (AN43C), flat-head(AN442), and brazier-head (AN4556) aluminum-alloy rivets because of the scarcity of information on the tensile strength of rivets. The results of the investigation are presented as curves that show the variation of the ratio of the tensile strength of the rivet to the tensile strength of the rivet crank with the ratio of the sheet thickness to the rivet diameter for the different types of rivet.

From Summary: "Guide fixtures are described by means of which axial fatigue loads including compression may be applied to a thin sheet-metal specimen. Tests indicate that the guides prevented buckling without bypassing the load or injuring the specimen."

From Summary: "This paper deals with the single problem if circular shell-supported frames subjected to concentrated loadings. A mathematical attack is developed and presented in the form of nondimensional-coefficient curves."

Report presenting a device that automatically analyses the data from a 45 degree strain rosette. The rosette strains are properly combined by means of an electric circuit to yield a direct meter reading of maximum shear strain and major and minor principal strains.

From Summary: "Charts are presented for rapidly determining the principal strains and stresses, the maximum shear strain and stress, and the orientation of principal axes from data on 45 degree strain rosettes. The charts may be used for analyzing the conventional data consisting of strains measured along three gage lines 45 degrees apart, but their application is more direct if the rosette data are obtained by means of special circuits that require the use of four gages 45 degrees apart."

Numerical methods have been developed for obtaining the steady, adiabatic flow field of a frictionless, perfect gas about arbitrary two-dimensional bodies. The solutions include the subsonic velocity regions, the supersonic velocity regions, and the transition compression shocks, if required. Furthermore, the rotational motion and entropy changes following shocks are taken into account. Extensive use is made of the relaxation method. In this report the details of the methods of solution are emphasized so as to permit others to solve similar problems. Solutions already obtained are mentioned only by way of illustrating the possibilities of the methods described. The methods can be applied directly to wind tunnel and free air tests of arbitrary airfoil shapes at subsonic, sonic, and supersonic speeds.

Note presenting an investigation of several laminated glass windshields to determine their suitability for use in airplanes with pressurized cabins. The various constructions of the extended portions of the windshields which serve for mounting purposes included plastic alone, plastic and one sheet of glass extended, plastic extension reinforced with an aluminum strip, and plastic extension reinforced with a steel strip. The results indicated that the laminated windshields with plastic-mounting extensions reinforced by aluminum or steel were resistant to creep and bursting at pressures of the order that will be encountered in service.

Report presenting experiments with both curved and flat reinforced sheet models, the longitudinals of which were loaded axially. The stress distribution in longitudinals and sheet was measured with electric strain gages.

"A solution of Von Karman's fundamental equations for plates with large deflections is presented for the case of a shear web divided into square panels by reinforcing struts. Numerical solutions are given for struts of infinite rigidity and for struts the weight of which is one-fourth the weight of the sheet. The results are compared with Wagner's diagonal tension theory as extended by Kuhn and by Langhaar. It is found that the diagonal tension theory as developed by Kuhn agrees best with the present paper in the practical range when r=1/4. Kuhn's theory is in especially good agreement for the force in the strut when r=1/4" (p. 1).

"A systematic account is given in part I of the use of dimensional analysis in constructing similarity conditions for models and structures. The analysis covers large deflections, buckling, plastic behavior, and materials with nonlinear stress-strain characteristics, as well as the simpler structural problems" (p. 1).

"A decrease in shear strengths for increasing D/t ratios was shown in a previous investigation of protruding-head aluminum alloy rivets in double shear conducted at Aluminum Research Laboratories in 1942. Since single shear joints are more common than double shear joints, it was desirable to extend the investigation to single shear joints. This reports describes the results of this investigation of single shear joints and also includes the results of the previous investigation on double shear joints" (p. 1).

Report presenting a note in two parts regarding simplified truss stability criteria. The first part covers the development of simplified criteria for the stability of planar pin-jointed trusses against buckling in the plane of the truss. The second part constitutes a report on tests carried out to verify the validity of the criteria developed in part one.

Note presenting compressive testing made on twenty-one 24S-T aluminum-alloy sheet-stringer panels 12 inches in length and 16 inches in developed width, reinforced by four Z stringers spaced 4 inches apart. Results regarding strains, buckling, and failure are provided.

"General thin-airfoil theory for a compressible fluid is formulated as boundary problem for the velocity potential, without recourse to the theory of vortex motion. On the basis of this formulation the integral equation of lifting-surface theory for an incompressible fluid is derived with the chordwise component of the fluid velocity at the airfoil as the function to be determined. It is shown how by integration by parts this integral equation can be transformed into the Biot-Savart theorem" (p. 1).

Note presenting an investigation of the effect of artificial aging on the strengths of driven rivets of the alloys used commercially for rivets: specifically, A17S-T, 17S-T, and 24S-T. The change in shear strength for each type of rivet after being exposed to artificial aging treatment of 10 hours at 375 degrees Fahrenheit applied to the driven rivets is described.

"Flat sheet panels of aluminum alloy (all 17S-T except for two specimens of 24S-T) were tested under normal pressures with clamped edge supports in the structures laboratory of the Guggenheim Aeronautical Laboratory, California Institute of Technology. The thicknesses used ranged from 0.010 to 0.080 inch; the panel sizes ranged from 10 by 10 inches to 10 by 40 inches; and the pressure range was from 0 to 60-pounds-per-square-inch gage. Deflection patterns were measured and maximum tensile strains in the center of the panel were determined by electric strain gages" (p. 1).