Report discusses an analysis and preliminary design of a control linkage that varies automatically with dynamic pressure. The advantages of the device, including greater lateral control than a fixed control linkage without additional aerodynamic balance, are detailed. The effect of variable linkage on lateral-control characteristics is also described.

"Formulas for the calculation of hinge-moment characteristics of an elevator with a spring tab have been developed in terms of basic aerodynamic parameters, spring stiffness, and airspeed. The formulas have been used in a study of the stick-force gradients on a pursuit airplane equipped with an elevator with a spring tab. Charts are presented showing the variation of stick-force gradient in accelerated flight over a large range of speed and the complete range of spring stiffness for various center-of-gravity locations, altitudes, and airplane sizes" (p. 1).

Report discussing some calculations made for the effects of water in cooling the inlet air of aircraft-engine cylinders. From Summary: "The estimates indicate that the cooling effect of the water on the inlet air can be more extensive than the cooling now obtained with the intercoolers or aftercoolers in the air-induction system. In connection with water recovery from the exhaust gas, the estimates indicate that sufficient water can be recovered from 50 percent of the exhaust gas to provide an inducted water-fuel ratio of 0.5."

Report discusses an investigation that was conducted to compare the strength and tightness of machine-countersunk flush-riveted joints assembled with NACA flush rivets and a type of commercial flush rivet. A comparison was also generated between the strength and tightness of counterpunched flush-riveted joints assembled with the same types of rivet. NACA's flush-riveted joints tended to be stronger and tighter than the commercial joints.

"Tests were run on a single-cylinder, air-cooled engine with a Wright C9GC cylinder to determine the improvement in cylinder-head cooling that can be obtained by building into the exhaust passage an insulating shield designed to protect the valve-guide boss and the exhaust-passage walls from the exhaust gas. The test results showed an appreciable improvement in cooling of the exhaust-valve-guide boss, of the guide bushing, and of the valve seat" (p. 1).

From Summary: "Local-instability tests of 24S-T aluminum-alloy formed Z- and channel-section columns were made in order to determine a length of test specimen that would avoid the increased strength associated with short lengths and also permit the occurrence of a convenient buckling pattern. The effect of column length on the critical compressive stress, on the average stress at maximum load, and on the number of half-waves of the buckling pattern is shown."

Report discusses methods of determining the iron contamination of used lubricating oil in order to study wear rates of piston rings and cylinder barrels of aircraft engines. Two methods of separating iron from used lubricating oil are presented. The results of the analyses of the oil are presented and the methods are evaluated.

Report discusses an apparatus that may be used for indicating the formation of fatigue cracks or for following the progress of cracks. Details of the experiment and discussion of the way in which the deflection-crack area relationship may be used to monitor fatigue cracks are included.

"Thirty-nine Z-sections formed from 24S-T aluminum-alloy sheet with the angle of bend between the flanges and the web varying from 5 degrees to 120 degrees were tested as columns. Angles of bend from 30 degrees to 120 degrees had little or no effect on the critical stress or on the average stress at maximum load for local instability of the columns. The lengths of the columns were such that at angles of bend below 30 degrees they failed by Euler buckling" (p. 1).

"The effects of changes in aileron rigging between 2 deg up and 2 deg down on the stick forces were determined from wind-tunnel data for a finite-span wing model. These effects were investigated for ailerons deflecting equally in both directions and linearly with stick deflection. Data were analyzed for a Frise, a sealed internally balanced, and a beveled-trailing-edge aileron" (p. 1).

Report discussing the effect of inlet-air temperature and cylinder displacement on the charge temperature of an internal-combustion engine at the end of the induction stroke. The experiment to test various types of cylinders and their results on the air temperature and pressure is described.

Report discusses the results of testing of rudder deflection for trim at low speeds in the critical wave-off condition. Depending on the lateral center-of-gravity location on the airplane, the useful load in the wings will change and the ability of the rudder to trim the airplane may be greatly improved.

Report discusses the "effects of oil introduced into the combustion chamber and of oil-spray piston cooling on the knock-limited performance of aircraft engines" (from Summary). A CFR engine and Allison V-1710 cylinder were used to test the rate of oil consumption, knock, and knock-limited brake mean effective pressure.

"An electronic circuit for instantaneously indicating angular velocity and acceleration, both positive and negative, of rotating masses is described; readings are taken on electrical indicating meters. The indicator is described in terms of general application. A circuit diagram, calibration curves, and a mathematical analysis of the differentiation circuit are included" (p. 1).

Report discusses the results of an investigation into the effectiveness of water injection into the combustion end zone of a spark-ignition engine cylinder for the suppression of knock. The injection angle was found to be very important for obtaining maximum results. The results of various angles and amounts of water were examined.

Report discusses a method developed to estimate the quantities of internal coolants required to prevent overheating of the aircraft cylinder when oxygen boost is applied. The formula and calculations related to inlet-air pressure, added oxygen, added water, added nitrogen, and total fluid weight are detailed.

Report discusses an investigation into static pressures in subsonic and supersonic flow over an airplane wing as measured by static-pressure tubes, a static-pressure belt, and orifices flush with the wing surface. The results obtained from the three types of measuring devices and a comparison to theoretical calculations are presented.

Report discusses measurements of the relaxation time of steam and nitrogen due to their importance as turbine-working fluids. Additional calculations regarding different nozzle lengths are included.

Report discusses the results of an investigation to compare the discharge characteristics of an alcohol feed ring and a standard alcohol discharge nozzle when utilized to supply anti-icing alcohol to the propeller-blade feed shoes on a Curtiss-Wright C-46 cargo airplane. The equipment used, testing practices, and results of the alcohol flow distribution are described.

Report discussing the results of testing conducted to determine the knock-limited performance of fuel blends containing 80 percent of S-2 reference fuel and 20 percent of several exploratory fuels. Butyl acetate, sec-butyl acetate, isopropyl acetate, sec-butyl alcohol, tert-butyl alcohol, isopropyl alcohol, cyclohexanol, methylcyclohexanol, isobutylcarbinol, sec-butylcarbinol, triethyl borate, and dimethylfuran were examined.

"A model of a flying boat was tested to determine the landing characteristics when the depth of the step was reduced to zero by means of a retractable planing flap on the forebody" (p. 4). The results of stability and resistance testing are presented.

Report discusses tests conducted using a model of a four-engine long-range flying boat with a 30 degree V-step and two different transverse steps of comparable positions and depths. The limits of stability, landing speed, and landing characteristics of the different models are presented.

Report discusses the results of tensile and compressive tests of two types of plastic-bonded glass cloth and their potential use in aircraft construction. The ultimate tensile stress and compressive yield stresses for the different materials are provided.

Report discusses the maximum lift coefficients for conventional and tailless airplanes in the gliding and landing conditions. Three areas are used to calculate the coefficients: wing area alone, wing area plus horizontal-tail area, and wing area plus horizontal- and vertical-tail areas.