From Introduction: "This report presents only that portion of the data from the first ditching which was to be used roughly establish the accelerations experienced by the pilot and the amount of water pressure to which the fuselage structure was subjected during the ditching."

Report presenting measurements of a Consolidated B-24D airplane of accelerations at various points on the wing during landing impacts. landings were made with the wheels initially stationary but free to rotate, with the brakes set before contact, and with the main wheels rotating prior to contact.

Report presenting tests made in the LMAL 16-foot high-speed tunnel to determine the aerodynamic characteristics of a 1000-pound AN-M-65-AZON radio-controlled bomb at a Mach number range of 0.2 to 0.6. Over the Mach number range, the hinge-moment coefficients, yawing-moment coefficients, and lateral-force coefficients exhibited no important changes with increasing speed.

Report presenting testing in the two-dimensional low-turbulence tunnels on a 24-inch-chord model of the NACA 66(215)-116 a = 0.6 airfoil with a 0.25-chord slotted flap. The optimum flap pivot positions were found for three different conditions. The conditions were determined from a consideration of the landing, take-off, and strafing requirements of the airplane.

Report presenting 10 practical-construction models of sections of helicopter rotor blades tested in the NACA two-dimensional low-turbulence pressure tunnel at atmospheric pressure. Lift, drag, and pitching-moment characteristics of blades representing the present method of construction of the YR-4A helicopter were determined.

Report presenting an analysis of data on fuel-vapor loss from fuel tanks during simulated flight obtained by six laboratories to show the effects of individual variables such as altitude, initial fuel temperature, rate of climb, booster-pump agitation, fuel depth, fuel-surface area, types of fuel, and vent-line pressure drop on fuel-vapor loss.

Report discusses an investigation into the behavior of a cantilever beam in transverse motion with a mass at its tip when the root is suddenly brought to rest. Equations for determining the stresses, deflections, and accelerations that arise in the beam are also provided. This testing can be applied to the shock created in an airplane when landing and the vibrations that result.

Report presents a series of charts used to demonstrate typical good and undesirable airplane characteristics as determined in flight that were used to facilitate discussion at a series of conferences between the National Advisory Committee, Army, Navy, and representatives of the aircraft industry. For each chart, the purpose of the test, the flight technique used, the items recorded, and the evaluation and interpretation of the data obtained were provided. Additional figures drawn on the board during the conferences are not reproduced in the report.

From Summary: "Compression tests were made of two groups of panel specimens with hat-section stiffeners. The groups were identical except that the flat sheet of one group was Alclad 24S-T81 and of the other Alclad 24S-T86. Results of the tests are given in tables or charts which show the average stress at which the sheet buckles and the average stress at the maximum load."

Report presenting testing to determine which of three spinner-diffuser designs on an NACA cowling was the most effective in cooling a Pratt & Whitney R-2800 engine installation. The results of pressure-distribution studies in front of and behind each bank of cylinders are presented for a wide range of propeller-operating conditions.

Report presenting results of compression tests of six paper-base plastic panels with outward-acting normal pressure. All panels failed by separation of the skin, either from the rib or from the stiffeners. Results regarding the introduction of air pressure and types of failures encountered are provided.

"Compression tests were made of 63 panels stiffened with corrugated sheet. The specimens were constructed from artificially aged alclad 24S-T aluminum alloy with minimum guaranteed yield strengths of 57 and 48 kips per square inch for the flat- and corrugated-sheet materials, respectively. Results of the tests are presented in charts which show the average stresses at the maximum load and at buckling of the sheet" (p. 1).

Report presenting an investigation of the cooling of a Franklin 6-AC-29S horizontally opposed cylinder air-cooled engine installed in a Fleetwings model 33 trainer. The cowling on the airplane did not provide satisfactory cooling, but several alterations were tested, including with cylinder baffles. Results regarding engine cooling, aerodynamics of the cowling installation, and predicted versus actual cowling performance are provided.

Testing of a dynamically similar model of an Army A-20A airplane to determine the best way to land the airplane in calm and rough water and to determine its probable ditching performance. Results regarding the effect of speed and attitude, effect of flap setting, effect of wind and seaway, effect of simulated damage, effect of sinking speed, effect of propellers, effect of gun blisters, and effect of weight are provided.

Report presenting testing to determine the best way to land the B-25 airplane in calm and rough water and to determine its probable ditching performance. By landing with flaps down in a tail-down attitude at as slow a speed as possible, smooth straight landing runs will probably result in calm water. Results regarding the effect of attitude, effect of flap setting, effect of simulated damage, effect of propellers, and effect of seaway are provided.

Report presenting tests made with a dynamic model of the Army B-26 airplane to determine its behavior when landed on water. Results regarding the general behavior, effect of flaps, effect of landing attitude and speed, tests with undamaged model, tests with simulated damage, tests with propellers, vertical decelerations, and effect of weight are provided.

Report presenting drag measurements in the two-dimensional low-turbulence tunnel of an available 100-inch-chord model of the NACA 23016 wing section. Results regarding the curves of section drag coefficient plotted against Reynolds number for various surface conditions and lift coefficients, variation of drag coefficient with lift coefficient, and effects of skin friction are provided.

Report presenting an investigation conducted with the propeller cuffs and spinner removed to determine their effect in flight on the pressure recovery of the cooling-air flow. Curves are presented to compare the pressure and temperature distribution over the front row of cylinders for flights with and without cuffs and spinner.

Report discussing the knock-limited performance of blends of triptane and 28-R fuel in an F-4 engine at three sets of conditions and three compression ratios. The knock limits of the triptane blends were more sensitive to compression ratio than the 28-R fuel, and the sensitivities of the blends increased as the severity of other engine conditions increased.

Report presenting an investigation conducted to determine the effect of water injection on the knock-limited performance of a V-type 12-cylinder liquid-cooled engine. The knock-limited performance tests were made at an engine speed of 3000 rpm with carburetor-air temperatures of 158, 101, and 50 degrees Fahrenheit at water-fuel ratios of 0, 0.2, 0.4, and 0.6.

Results are presented for tests of two wings, an NACA 230-series wing and a highly-cambered NACA 66-series wing on a twin-engine pursuit airplane. Auxiliary control flaps were tested in combinations with each wing. Data showing comparison of high-speed aerodynamic characteristics of the model when equipped with each wing, the effect of the auxiliary control flaps on aerodynamic characteristics, and elevator effectiveness for the model with the 66-series wing are presented. High-speed aerodynamic characteristics of the model were improved with the 66-series wing.

Report discussing the results of using an enlarged vertical tail on a P-63A-1 on directional stability. The tests included measurements of the amount of sideslip at various speeds and normal accelerations. Potential required modifications for increased performance using the larger tail are also described.

Report discussing testing on triptane, hot-acid octane, diisopropyl, neohexane, mixed xylenes, cumene, benzene, toluene, and methyl tert-butyl ether in several blends to determine their knock-limited performance data in F-3 and F-4 engines at standard operating conditions. All of the blending agents examined were found to be usable, with concentrations varying depending on various thermodynamic properties.

Report discussing the cooling characteristics of a 14-cylinder double-row radial air-cooled engine in a four-engine airplane. The effects of charge-air flow, cooling-air pressure drop, and fuel-air ratio on the cooling characteristics were measured separately. The cooling equation, rear middle-barrel temperature, cooling-limited manifold pressure, and maximum cruising power versus temperature-limited power are described.