Report presenting testing to obtain experimental confirmation of the effect of air compressibility on cooling and pressure loss of a baffled cylinder barrel and to evaluate various methods of analysis. Testing occurred over a wide range of air flows and density altitudes.

Report presenting an analysis of the power losses in airplane flight of cross-flow plate and tubular intercoolers to determine the cooling-air weight flow and pressure drop that give minimum total power loss for any given cooling effectiveness. The investigation covers a range of flight conditions of altitude, airspeed, lift-drag ratio, supercharger-pressure ratio, and adiabatic efficiency.

Report presenting an investigation of the icing and de-icing characteristics of a Pratt & Whitney R-1830 engine induction system. The current report covers a program to determine the most effective rate and method of injection of de-icing fluid to remove a heavy ice formation from the induction system. Results regarding the flow rates, recovery times, de-icing portions of the runs, and ice formation characteristics are provided.

Report presenting a theoretical investigation of the two-dimensional, incompressible potential flow past a symmetrical lattice of airfoils of arbitrary shape. Expressions are given for evaluation of the velocity and pressure distribution at the airfoil boundary.

Report presenting flight measurements made on a modern pursuit airplane to determine the approximate magnitude of the horizontal tail loads in accelerated flight. Pressures at a few points were used as an index of the tail loads by correlating these pressures with complete pressure-distribution data obtained in the NACA full-scale tunnel.

Report presenting the use of the Ackeret iteration process to obtain higher approximations than that of Prandtl and Glauert for the flow of a compressible fluid past a circular arc profile. The procedure is to expand the velocity potential in a power series of the camber coefficient.

Report presenting the potential function for flow, with circulation, of a compressible fluid about a circular cylinder, which is obtained in series form including terms of the order of M(exp 4) where M is the Mach number of the free stream. The equations are used to obtain pressure coefficient as a function of Mach number at a point on the surface of the cylinder for different values of circulation.

Report presenting equations for calculating the stick-force characteristics obtained with a spring-tab type of elevator control. The main problems encountered in the design of the satisfactory elevator spring tab are to provide stick forces in the desired range, to maintain the force per g sufficiently constant throughout the speed range, to avoid undesirable "feel" of the control in ground handling, and to prevent flutter.

"This report outlines the flight conditions that are usually critical in determining the design of components of an airplane which affect its stability and control characteristics. The wind-tunnel tests necessary to determine the pertinent data for these conditions are indicated, and the methods of computation used to translate these data into characteristics which define the flying qualities of the airplane are illustrated" (p. 1).

Report presenting testing of several designs of nitrided-steel piston rings under variable conditions of output. Testing indicated the importance of good surface finish and conformity of the ring to the bore. Results regarding temperature tests, single-cylinder-engine tests, and multicylinder-engine tests are provided.

Report presenting tunnel-wall corrections for an airfoil of finite thickness and camber in a two-dimensional-flow wind tunnel. The theory takes account of the effects of the wake of the airfoil and of the compressibility of the fluid and is based on the assumption that the chord of the airfoil is small in comparison with the height of the tunnel. The theoretical results are compared with the small amount of low-speed experimental data available and agreement is seen to be satisfactory, even for relatively large values of the chord-height ratio.

Report presenting a method of constructing fins of nearly optimum proportions to the point where a cylinder has been manufactured and tested. Data were obtained on cylinder temperature for a wide range of inlet-manifold pressures, engine speeds, and cooling-pressure differences. Results regarding cooling equations, cylinder-temperature relationships, and a comparison of three cylinder cooling performances are provided.

Report presenting icing tests on a Bendix-Stromberg PD-12F5 carburetor mounted on a Pratt & Whitney R-1830-C4 intermediate rear engine section. Limiting icing conditions were established for simulated cruising power and simulated rated power over a range of carburetor-air temperatures, and relative humidities are provided.

From Introduction: "The purpose of this analysis was to investigate the use of function of intake-manifold temperature and pressure, exhaust back pressure, and engine speed in place of a ventri as a means of measuring engine air consumption and to determine if this function is suitable for automatic mixture control."

"A method of conformal transformation is developed that maps an airfoil into a straight line, the line being chosen as the extended chord line of the airfoil. The mapping is accomplished by operating directly with the airfoil ordinates. The absence of any preliminary transformation is found to shorten the work substantially over that of previous methods. Use is made of the superposition of solutions to obtain a rigorous counterpart of the approximate methods of thin-airfoils theory" (p. 1).

"This report describes tests in the Langley 16-foot high-speed tunnel to determine whether these failures could be attributed to changes in the aerodynamic characteristics of the ailerons at high speeds" (p. 1).

"A correlation of what are believed to be the most reliable data available on duct components of aircraft power-plant installations is presented. The information is given in a convenient form and is offered as an aid in designing duct systems and, subject to certain qualifications, as a guide in estimating their performance. The design and performance data include those for straight ducts; simple bends of square, circular, and elliptical cross sections; compound bends; diverging and converging bends; vaned bends; diffusers; branch ducts; internal inlets; and an angular placement of heat exchangers" (p. 1).

"Detailed methods are presented for determining the corrections to results from wind-tunnel tests of three-dimensional models for the effects of the model-support system, the nonuniform air flow in the tunnel, and the tunnel walls or jet boundaries. The procedures for determining the corrections are illustrated by equations and the required tests are discussed. Two general methods that are used for determining and applying the corrections to force tests are discussed" (p. 1).

Report contains detailed results of a number of fatigue tests on spot-welded joints in aluminum alloys. The tests described include: (1) fatigue tests on spot-welded lap joints in sheets of unequal thickness of alclad 24s-t. These tests indicate that the fatigue strength of a spot-welded joint in sheets of two different gages is slightly higher than that of a similar joint in two sheets of the thinner gage but definitely lower than that of a similar joint in two sheets of the thicker gage. (2) Fatigue tests on spot-welded alclad 75s-t spot-welded lap-joint specimens of alclad 75s-t were not any stronger in fatigue than similar specimens of alclad 24s-t. (3) Fatigue tests on lap-joint specimens spot -welded after various surface preparations--these included ac welding wire-brushed surfaces, dc welding wire-brushed surfaces, and dc welding chemically cleaned surfaces. While the ac welds were strongest statically, the dc welds on wire-brushed surfaces were strongest in fatigue. Specimens prepared in this way were very nearly as strong as the best riveted specimens tested for comparison. (4) Fatigue tests on specimens spot-welded with varying voltage so as to include a wide range of static spot-weld strengths. The fatigue strengths were in the same order as …

Report includes tension fatigue test results on the following types of samples of 0.040-inch alclad 24s-t: (1) monoblock sheet samples as received and after a post-aging heat treatment, (2) "sheet efficiency" samples (two equally stressed sheets joined by a single transverse row of spot welds) both as received and after post-aging, (3) spot-welded lap-joint samples as received and after post-aging, and (4) roll-welded lap-joint samples. (author).

"The results of a series of tests to determine the effect of internal pressure on the buckling load of a thin cylinder under an applied torque indicated that internal pressure raises the shear buckling stress. The experimental results were analyzed with the aid of previously developed theory and a simple interaction formula was derived" (p. 1).

"The design of curved sheet panels to resist shear involves a consideration of several factors: the buckling resistance of the sheet, the stress at which buckling becomes permanent, and the strength which may be developed beyond the buckling limit by tension-field action. Although some experimental as well as theoretical work has been done on the buckling and tension-field phases of this problem, neither of these types of action appears to be very well understood. This report presents the results of the first series of torsion tests of stiffened circular cylinders to be completed in connection with this study at Aluminum Research Laboratories" (p. 1).

In open box beams subjected to torsion, secondary stresses arise owing to lateral bending of the spar caps. The present paper outlines a simple method for estimating the magnitude of these stresses and gives the results of tests of an open box beam in the neighborhood of a discontinuity where the cover changed from the top to the bottom of the box.

Report discusses pressure-distribution tests of a plain flap with interchangeable beveled trailing edges on an NACA 0009 airfoil. The flap chord was 30 percent of the airfoil chord and the bevel chords were 15 and 20 percent of the flap chord. The purpose of these tests was to supply pressure-distribution data that may be used for structural and aerodynamic design of horizontal and vertical tail surfaces.