Report presenting cyclic torsion tests made to determine the effects of varying amounts of torsional overstrain on the shape of the shearing stress-strain diagrams of aluminum alloy 17ST, mild steel, wrought iron, copper, brass, and magnesium alloy AX57S. Results regarding the tensile, compressive, and shear properties are provided.

"Wind-tunnel tests were performed to determine the drag of the front-wheel arrangements of several types of tricycle landing gear. One wheel was tested in arrangements to simulate both nonretracted and partially retracted types. The landing gears were tested in conjunction with a fuselage, and the effects of wheel extension and longitudinal location were determined" (p. 1).

"The pack method for determining compressive stress-strain graphs described in NACA Report No. 649 has been modified to extend it's application to thinner gages and stronger materials. The principal modifications consisted in the provision of additional support against instability cementing the specimens of the pack together with fused shellac and the provision of special clamps to hold the specimens together while the test is in progress. The shellac was found to increase the buckling load of the pack without any appreciable effect on the compressive stress-strain graph of the material" (p. 1).

Note presenting a method developed for the direct measurement of the average heat-transfer coefficient from the gases in the cylinder during the cycle of operation of an internal-combustion engine. Experimental measurmeents were made with a heat collector projecting through a spark-plug hole into the combustion chamber of the test engine in order to examine the effects of several engine-operating and design parameters on the mean heat transfer to the collector.

The National Advisory Committee for Aeronautics conducted exhaust-heat de-icing tests in flight to provide data needed in the application of this method. The capacity to extract heat from the exhaust gas for de-icing purposes, the quantity of heat required, and other factors were examined. The results indicate that a wing-heating system employing a spanwise exhaust tube within the leading edge of the wing removed 30 to 35 percent of the heat from exhaust gas entering the wing. Data are given from which the heat required for ice prevention can be calculated. Sample calculations have been made on the basis of existing engine power/wing area ratios to show that sufficient heating can be obtained for ice protection on modern transportation airplanes, provided that uniform distribution of the heat can be secured.

"The use of different forms of wide-flange, thin-wall steel beams is becoming increasingly widespread. Part of the information necessary for a national design of such members is the knowledge of the stress distribution in and the equivalent width of the flanges of such beams. This problem is analyzed in this paper on the basis of the theory of plane stress. As a result, tables and curves are given from which the equivalent width of any given beam can be read directly for use in practical design" (p. 1).

Note presenting testing of a simplified type of all-metal wing construction of 18-8, spot-welded except for skin attachment, by means of hydrostatic loading, the wing being proportioned to permit close representation of typical conditions by means of the waterhead. The results showed the possibility of eliminating almost all of the stiffeners from a stressed-skin wing, the possible reduction of weight in a lightly loaded wing and of substantial cost in the construction of any all-metal wing.

"An investigation was made in the 7-by-10 foot wind tunnel to determine the effects of dorsal-type fins and various arrangements of fins on the aerodynamic characteristics of a streamline circular fuselage. Comparative plots of the aerodynamic characteristics of the fuselage alone and the fuselage with various fin arrangements are given to show their effects on coefficients of yawing moment, drag, and lateral force. Results are also given for one case in which a rear fin on a circular fuselage was faired with modeling clay to obtain a fuselage shape with the same side elevation as the fuselage with the unfaired fin but with an elliptical cross section over the rearward portion of the fuselage."

"An investigation has been made in the NACA 7- by 10-foot wind tunnel of a large chord NACA 23021 airfoil equipped with two arrangements of a completely extended 15 percent chord extensible flap. One of the flaps had a faired juncture, without a gap; the other was provided with a slot between the trailing edge of the airfoil and the nose of the flap. The results showed that the basic airfoil gave the lowest profile-drag coefficients over the low lift range, the airfoil with the plain extensible flap gave the lowest profile-drag coefficients over the moderate lift range, and the airfoil with the slotted extensible flap gave the lowest profile-drag coefficients over the high lift range" (p. 1).

From Summary: "Two topics of interest to persons attempting to apply the heat method of preventing ice formation on aircraft are considered. Surfaces moving through air at high speed are shown, both theoretically and experimentally, to be subject to important aerodynamic heating effects that will materially reduce the heat required to prevent ice. Numerical calculations of the path of water drops in an air stream around a circular cylinder are given. From these calculations, information is obtained on the percentage of the swept area cleared of drops."

"An investigation has been made to determine efficient arrangements for an internal-flow system of an aircraft when such a system operates by itself or in combination with other flow systems. The investigation included a theoretical treatment of a problem and tests in the NACA 5-foot vertical wind tunnel of inlet and outlet openings in a flat plate and in a wing. When an internal-flow system tends to decrease the final velocity of it's wake, the results showed that it should be arranged in series with the propulsive system; the inlet opening should be located at a forward stagnation point; and the outlet opening should be so shaped and located as to recover the kinetic energy of the jet without increasing the drag of other portions of the aircraft" (p. 1).

"A mathematical analysis has been made to show the method of obtaining the dimensions of the intercooler that will use the least total power for a given set of design conditions. The results of this analysis have been used in a sample calculation and, on the basis of this calculation, a new inter cooler arrangement is suggested. Because the length of the two air passages of the new arrangement is short in comparison with the third dimension, the height of the intercooler, this intercooler arrangement has unusual dimensions" (p. 1).

"A compilation of the experimentally determined moments of inertia of 32 airplanes is presented. The measurements were obtained at the laboratories of the NACA by means of a pendulum method. The airplanes tested are representative of several types of aircraft of gross weight less than 10,000 pounds. The results are presented in coefficient as well as in dimensional form. An elementary analysis of the data disclosed the possibility of grouping the results according to wing type of the airplane, as low-wing monoplanes, parasol and high-wing monoplanes, and biplanes" (p. 1).

From Summary: "A discussion is given of the important aspects of the stalling of vertical tail surfaces. The type of instability encountered is described and the possibilities of inadvertent occurrence are noted. The influence of directional flight tests on the behavior of a airplane when the tail stall takes place is discussed. In this connection, flight tests of a twin-engine airplane in which the vertical fin area was increased are cited."

From Introduction: "In order to afford a means of comparison and to obtain a clear understanding of the results, a study of the effects of normal angular deflections of the ailerons, with and against the spin, was included in the investigation. Ailerons deflected with the spin means that the ailerons are deflected with right aileron up and left aileron down in a right spin. The results of the investigation are discussed in this paper."

From Summary: "This paper does not attempt to establish criterions for directional stability and control; rather, the emphasis is placed on providing some basis for design to specified criterions. An example applying the design methods has been included."

"The ionization in the knock zone of an internal-combustion engine was investigated. A suspected correlation between the intensity of knock and the degree of ionization was verified and an oscillation in the degree of ionization corresponding in frequency to the knock vibrations in the cylinder pressure was observed" (p. 1).

"An investigation was made to determine the effect of mixture strength and of normal as well as optimum spark timing on the combustion, on the cylinder temperature, and on the performance characteristics of an engine. A single-cylinder test unit utilizing an air-cooled cylinder and a carburetor and operating with gasoline having an octane rating of 92 was used. The investigation covered a range of fuel-air ratios from 0.053 to 0.118. Indicator diagrams and engine-performance data were taken for each change in engine conditions" (p. 1).

Report presenting a chart for the coefficient K in the formula for the critical compressive stress for flat rectangular plates compressed in one direction.

"An investigation was made of the effect of the wing wake on the lift of the horizontal tail surfaces. In the development of expressions for this effect, the growth of wing circulation and wing wake, the time interval represented by the tail length, and the development of lift by the rail were considered. The theory has been applied to a specific case to show the magnitude of the effect to be expected. It is shown that, for motions below a certain frequency, the development of lift by the tail may be represented by a simple lag function. The lag is, however, somewhat greater than that indicated by the rail length" (p. 1).

From Summary: "Data are presented to show the effects of inlet-air pressure, inlet-air temperature, and compression ratio on the maximum permissible performance obtained with having a hemispherical-dome combustion chamber. The five aircraft-engine fuels used have octane numbers varying from 90 to 100 plus 2 ml of tetraethyl lead per gallon. The data were obtained on a 5 1/4-inch by 4 3/4-inch liquid-cooled engine operating at 2,500 r.p.m. The compression ratio was varied from 6.0 to 8.9. The inlet-air temperature was varied from 110 to 310 F. For each set of conditions, the inlet-air pressure was increased until audible knock occurred and then reduced 2 inches of mercury before data were recorded."

Six 100-octane and two 87-octane aviation engine fuels were tested in a modified C.F.R. variable-compression engine at 1,500, 2,000 and 2,500 rpm. The mixture temperature was raised from 50 to 300 F in approximately 50 degree steps and, at each temperature, the compression ratio was adjusted to give incipient knock as shown by a cathode ray indicator. The results are presented in tabular form. The results are analyzed on the assumption that the conditions which determine whether a given fuel will knock are the maximum values of density and temperature reached by the burning gases. A maximum permissible density factor, proportional to the maximum density of the burning gases just prior to incipient knock, and the temperature of the burning gases at that time were computed for each of the test conditions. Values of the density factors were plotted against the corresponding end-gas temperatures for the three engine speeds and also against engine speed for several and end-gas temperatures. The maximum permissible density factor varied only slightly with engine speed but decreased rapidly with an increase in the end-gas temperature. The effect of changing the mixture temperature was different for fuels of different types. The results emphasize the desirability of …

"Comparative full-scale and model spin tests were made with a low-lying monoplane in order to extend the available information as to the utility of the free-spinning wind tunnel as an aid in predicting full-scale spin characteristics. For a given control disposition the model indicated steeper spins than were actually obtained with the airplane, the difference being most pronounced for spins with elevators up. Recovery characteristics for the model, on the whole, agreed with those for the airplane, but a disagreement was noted for the case of recovery with elevators held full up" (p. 1).

From Summary: "Studies were made of the air movements in the NACA glass-cylinder apparatus using cylinder heads similar to those on the Wright R-1820-G engine and the Pratt & Whitney Wasp engine as modified by the Eclipse Aviation Corporation to use fuel-injection equipment. The air movements were made visible by mixing small feathers with the air; high-speed motion pictures were than taken of the feathers as they swirled about the inside the glass cylinder. The test engine speeds were 350, 500, and 1,000 r.p.m. Motion pictures were also taken of gasoline sprays injected into the cylinder during the intake stroke. The air flow produced by each cylinder head is described and some results of the velocity measurements of feathers are presented. The apparent time intervals required for vaporization of the gasoline sprays are also given."