"A flight investigation was made of the increase in effectiveness of ailerons that can be obtained by preventing flow of air through the wing at the hinges and of the possibility of reducing the aileron operating force by replacing ailerons having normal open hinge gaps with narrower but equally effective ailerons having sealed hinge gaps. Tests were made with a Fairchild 22 airplane with two sizes of plain unbalanced ailerons, one set having a chord equal to 0.18c, and the other chord equal to 0.09c. The results of the investigation show that improvement of the lateral-control effectiveness is obtained by completely preventing the flow of air through the wing at the hinge axis of conventional ailerons" (p. 1).

An optically recording engine-pressure indicator of simple and rugged construction has been developed for use in high-pressure and high temperature combustion research. This instrument is of the diaphragm type and has a natural frequency of about 10,000 cycles per second.

Three rectangular monoplane wings having rounded tips were tested on the N.A.C.A. spinning balance in the 5-foot vertical wind tunnel. The airfoil sections used were the N.A.C.A. 0009, 23018, and 6718. The aerodynamic characteristics of the models and a prediction of the angles of sideslip for steady spins are given. There is included an estimate of the yawing moment that must be furnished by parts of the airplane to balance the inertia couples and wing yawing moments for spinning equilibrium. The predicted angles of sideslip and yawing moments required for spinning equilibrium for a Clark Y wing with the same form are included for comparison.

"An investigation was conducted in the NACA 20-foot wind tunnel of the ramming effect of three general types of carburetor intake rams for radial engines, namely, the internal constant area type, the external constant area type, and the external expanding type. The rams were installed on a radial air- cooled engine nacelle, and tests were made with and without the propeller operating. The results indicated that the external types having entrances near the front of the engine cowling gave the greatest ramming effect" (p. 1).

"Wind-tunnel data are presented on the rate of change of yawing moment with sideslip for tests of 9 complete airplane models, 20 fuselage shapes, and 3 wing models with various combinations of dihedral, sweepback, and twist. The data were collected during a survey of existing information, which was made to find a reliable method of computing the yawing moment due to sideslip. Important errors common to methods of computation used at present appear to be due to large interference effects, the investigation of which will undoubtedly require an extensive program of systematic wind-tunnel tests. At present it is necessary to place considerable reliance on past design experience in proportioning an airplane so as to obtain a reasonable degree of directional stability" (p. 1).

"Preliminary information on the complex subject of the fatigue strength of fabricated structural members for aircraft is presented in the test results obtained on several different types of airship girders subjected to axial tension and compression in a resonance fatigue machine. A description of this machine as well as numerous photographs of the fatigue failures are given. There is also presented an extended bibliography on the subject of fatigue strength" (p. 1).

A model of one of the twin hulls of the Italian Savoia S-55-X flying boat (N.A.C.A. Model 46) was tested in the N.A.C.A. tank according to the general method. The data obtained from these tests cover a broad range of speeds, loads, and trims and are given in nondimensional form to facilitate their use in applying this form of hull to any other flying boat or comparing it's performance with the performance of any other hulls. The results show that the resistance characteristics at best trim of this model are excellent throughout the speed range. In order to compare the performance of the S-55-X hull with that of the 35, a pointed-step hull developed at the N.A.C.A. tank, the data are used in the computations of take-off example of a twin-hull, 23,500-pound flying boat. The calculations show that the S-55-X hull has better take-off performance.

"As part of the wing-fuselage interference program in progress in the NACA variable-density wind tunnel, a method of eliminating the interference bubble associated with critical mid wing combinations was investigated. The interference bubble of the critical mid wing combination was shown to respond to modification at the nose of the juncture and to be entirely suppressed with little or no adverse effect on the high-speed drag by special leading edge fillets" (p. 1).

"The round fuselage of an unfilleted low-wing combination was modified to incorporate straight-side junctures. The resulting combination, with or without horizontal tail surfaces, had practically the same aerodynamic characteristics as the corresponding round-fuselage tapered-fillet combination" (p. 1).

"As part of the wing-fuselage interference investigation in progress in the N.A.C.A. variable density wind tunnel, the effects of various split-flap arrangements applied to wing-fuselage combinations were determined. Split flaps were found to exert their influence independently of the interference, and their effects on the aerodynamic characteristics of rectangular-airfoil combinations appeared to be more or less proportional to their exposed span lengths. The interference, moreover, showed the same character with the split flaps as without them" (p. 1).

From Summary: "Boundary-layer surveys were made throughout the transition region along a smooth flat plate placed in an airstream of practically zero turbulence and with an adverse pressure gradient. The boundary-layer Reynolds number at the laminar separation point was varied from 1,800 to 2,600. The test data, when considered in the light of certain theoretical deductions, indicated that transition probably began with separation of the laminar boundary layer."

"N.A.C.A. Model 36, a hull form with parallel middle body for half the length of the forebody and designed particularly for use with stub wings, was tested according to the general fixed-trim method over the range of practical loads, trims, and speeds. It was also tested free to trim with the center of gravity at two different positions. The results are given in the form of nondimensional coefficients. The resistance at the hump was exceptionally low but, at high planing speeds, afterbody interference made the performance only mediocre" (p. 1).

From Summary: "Data are presented to show the effects of inlet-air pressure, inlet-air temperature, and compression ratio on the maximum permissible performance obtained on a single-cylinder test engine with aircraft-engine fuels varying from a fuel of 87 octane number to one 100 octane number plus 1 ml of tetraethyl lead per gallon. The data were obtained on a 5-inch by 5.75-inch liquid-cooled engine operating at 2,500 r.p.m. The compression ratio was varied from 6.50 to 8.75. The inlet-air temperature was varied from 120 to 280 F and the inlet-air pressure from 30 inches of mercury absolute to the highest permissible."

From Summary: "Results are given of pressure-distribution measurements made in flight over the right wing cellule and the right half of the horizontal tail surfaces of a dive-bombing biplane. Simultaneous measurements were also taken of the air speed, control-surface positions, control forces, and normal accelerations during various abrupt maneuvers in vertical plane. These maneuvers consisted of push-downs and pull-ups from level flight, dives and dive pull-ups from inverted flight. Besides the pressure measurements, flight tests were made to obtain (1) wing-fabric deflections during dives and (2) variation of the minimum drag coefficient with Reynolds Number."

The factors affecting the stalling characteristics of modern airplanes are briefly discussed. The effect of present-day design trends is shown and means for improving the stalling characteristics of future airplanes are indicated.

It is shown that the normal resistance curve for a flying boat may be approximated by two straight lines. The equations for take-off distance and time, derived from this approximation, are applied to a series of flying boats and the resulting factors are plotted in non dimensional form in a series of charts. Take-off performances from the charts are shown to be in good agreement with step-by-step integrations. Some applications of the charts to the solution of general design problems are included.

"Wind tunnel tests of a 15-foot-span model of a two-engine low wing transport airplane were made as a preliminary study of the emergency arising from the failure of one engine in flight. Two methods of reducing the initial yawing moment resulting from the failure of one engine were investigated and the equilibrium conditions were explored for two basic modes on one engine, one with zero angle of sideslip and the other with several degrees of sideslip. The added drag resulting from the unsymmetrical attitudes required for flight on one engine was determined for the model airplane" (p. 1).

The effect on cooling of baffle length with optimum cylinder finning is discussed. Results from tests of several streamlined cylinders are given. It is shown that by employing several baffles the cooling can be increased several times.

Tests on a high-speed single-cylinder engine are described. The regularity of the spark timing was varied by driving the timer from different engine shafts. A simple and reasonably accurate method of determining the spark timing is described. The results show that irregular spark timing may cause large errors in tests of the knocking properties of fuels. For the engine tested, it was found that a change of one crankshaft degree in spark restart was equivalent to an 0.85 inch Hg change in allowable inlet pressure.

"The increase in the frictional resistance of a surface caused by the presence of rivet heads was determined by towing four planing surfaces of the same dimensions. One surface was smooth and represented a surface without rivet heads or one with perfectly flush countersunk rivets. The other three surfaces were each fitted with the same number of full-size rivet heads but of a different type arranged in the same pattern on each surface" (p. 1).

"Tests were made of the Clark Y wing having split flaps with a gap between the flap and the lower surface of the wing. Lift, drag, and pitching moments were measured for the wing with three different sizes of flap. It was found that any gap between the flap and the wing reduced the lift, the drag, and the pitching moments, but that the center-of-pressure movement and the ratio of lift to drag were little affected" (p. 1).

Flight tests were made to demonstrate the particularity of employing fixed tabs in conjunction with a suitably designed differential linkage to reduce the force required to operate ailerons. The tests showed the system to be practicable with tabs of the inset type. The relative ineffectiveness of attached tabs for changing the aileron floating angle rendered them unsuitable. Experience gained in the investigation has indicated that the use of the system is limited to maximum deflections of one aileron relative to the other of less than 30 degrees and that the differential linkage should always be designed on the basis of the highest probable floating angle.

"An investigation was conducted to obtain fuel-consumption curves for a single-cylinder engine with a Wright 1820-G and Pratt & Whitney 1340-H cylinder at varying speeds, manifold pressures, and air-fuel ratios. The 1340- H cylinder was tested at speeds from 1,200 to 2,400 r.p.m. and at manifold pressures from 21 to 38 inches of mercury absolute. Less than extensive tests were made of the 1820-G cylinder. The results of the tests showed that the minimum brake fuel consumption was obtained when the engines were operating at high torques and at speeds from 60 to 70 percent of the rated speed" (p. 1).

An analysis of the cooling problems for a finned cylinder is made on the basis of the known fundamental principles of heat transfer from pipes. Experimental results that support the analysis are presented. The results of previous investigations on the problem are evaluated on the basis of the analysis and the results. An illustration of the application of these principles to a specific problem is included.