From Introduction: "The information now available concerning wing cut-outs or applicable to the analysis of their effects is plentiful (references 1 to 7) but too disconnected and unorganized to be of the greatest possible usefulness. In connection with the interference program being conducted in the N.A.C.A. varible-density wind tunnel, an analysis was therefore made of existing material to determine the qualitative effects of the different features of wing cut-outs, and to obtain means of calculating wing characteristics as affected by them."

From Summary: "The purpose of this report is to make the complicated processes on the direct-lift propeller amenable to analysis and observation. This is accomplished by placing the physical phenomena, starting with the most elementary process, in the foreground, while limiting the mathematical treatment to the most essential in view of the fundamental defects of the theorems. Comparison with model experiments supplements and corroborates the theoretical results."

Report includes the National Advisory Committee for Aeronautics letter of submittal to the President, Congressional report, summaries of the committee's activities and research accomplished, bibliographies, and financial report.

From Summary: "A comparatively simple method of calculating length of take-off run is developed from the assumption of a linear variation in net accelerating force with air speed and it is shown that the error involved is negligible. Detailed instructions are given for application of the formula and for the calculation of all factors involved."

"The ignition lag of a fuel oil in the combustion chamber of a high speed compression-ignition engine was measured by three different methods. The start of injection of the fuel as observed with a Stoborama was taken as the start of the period of ignition lag in all cases. The end of the period of ignition lag was determined by observation of the appearance of incandescence in the combustion chamber, by inspection of a pressure-time card for evidence of pressure rise, and by analysis of the indicator card for evidence of the combustion of a small but definite quantity of fuel" (p. 1).

From Summary: "Data obtained at the N.A.C.A. tank from tests on the models of three flying-boat hulls - N.A.C.A. models 11-A, 16, and 22 - are used to demonstrate the effect of trim angle on water resistance. A specific example is taken, and data from Model 11-A are used to show that the trim angle giving the minimum water resistance will give minimum total air-plus-water resistance. Total-resistance curves for best trimmed angles and other angles are compared for the same example."

This reports presents a method of calculating time and gross load for take-off of seaplanes and flying boats.

The viewpoints are discussed, according to which the scavenging of two-stroke-cycle engines can be evaluated, and the relations between scavenging pressure and the quantity of the scavenging medium required, as also between the scavenging pressure and the revolution speed, are developed. It is further shown that the power increase is limited by the scavenging process, so that further researches are desirable for qualitative improvement. These results lead to several conclusions regarding the propulsion of motor vehicles by the two-stroke-cycle engines.

This report describes recent improvements in the design of the equipment associated with the hot-wire anemometer for the measurement of fluctuating air speeds in turbulent air flow, and presents the results of some experimental investigations dealing with the response of the hot wire to speed fluctuations of various frequencies. Attempts at measuring the frequency of the fluctuations encountered in the Bureau of Standards' 54-inch wind tunnel are also reported. In addition, the difficulties encountered in the use of such apparatus and the precautions found helpful in avoiding them are discussed.

"This paper contains a series of calculations showing how the performance of controllable propellers may be derived from data on fixed-pitch propellers given in N.A.C.A. Technical Report No. 350, or from similar data. Sample calculations are given which compare the performance of airplanes with fixed-pitch and with controllable propellers. The gain in performance with controllable propellers is shown to be largely due to the increased power available, rather than to an increase in efficiency" (p. 1).

A general description of the small DVL wind tunnel is provided, with emphasis on air conduction, blower and velocity regulation, velocity measurement, and balance and model suspension.

Three tapered airfoils based on the N.A.C.A. 2200, the N.A.C.A.-M6, and the Clark Y sections were tested in the variable-density wind tunnel at a Reynolds Number of approximately 3,100,000. The models, which were of aspect ratio 6, had constant core center sections and rounded tips, and tapered in thickness from 18 percent at the roots to 9 percent at the tips. The aerodynamic characteristics are given by the usual dimensionless coefficients plotted for both positive and negative angles of attack and by effective profile-drag coefficients plotted against lift coefficients.

"This report gives the results of measurements of the lift, drag, and propeller characteristics of several wing and nacelle combinations with a tractor propeller" (p. 1). The liquid-cooled engines appeared to have an advantage over the air-cooled engines.

"The investigation of the effect of mass distribution on the spinning of airplanes initiated with tests on the NY-1 airplane has been continued by tests on another airplane in order to increase the scope of the information and to observe particularly the behavior of an airplane that shows considerable change in sideslip angle for its various conditions of spinning. The XN2Y-1 naval training biplane was used for the present tests in which changes of ballast along the longitudinal and lateral axes and changes of aileron, stabilizer, and elevator settings were made. The effects of these changes on the steady spin were measured in flight' (p. 185).

This report presents an extension of the autogiro theory of Glauert and Lock in which the influence of a pitch varying with the blade radius is evaluated and methods of approximating the effect of blade tip losses and the influence of reversed velocities on the retreating blades are developed. A comparison of calculated and experimental results showed that most of the rotor characteristics could be calculated with reasonable accuracy, and that the type of induced flow assumed has a secondary effect upon the net rotor forces, although the flapping motion is influenced appreciably. An approximate evaluation of the effect of parasite drag on the rotor blades established the importance of including this factor in the analysis.

This report is the fourth of a series giving the results obtained from wind tunnel tests to determine the interference lift and drag and propulsive efficiency of wing-nacelle-propeller combinations. Previous reports give the results of tests with tractor propellers with various forms of nacelles and engine cowlings. This report gives the results of tests of tandem arrangements of engines and propellers in 11 positions with reference to a thick wing.

"This report is the fifth of a series giving the results obtained from wind tunnel tests on the interference drag and propulsive efficiency of nacelle-propeller-wing combinations. This report gives results of tests of an NACA cowled air-cooled engine nacelle with tractor propeller located in 12 positions with reference to a Clark Y biplane cellule" (p. 603).

From Introduction: "The investigation was intended to cover the characteristics of individual cups and of similar cups mounted on complete cup wheals. This report treats the static tests run on the individual cups."

Circular describing the Avia 51 commercial airplane, which is a Czechoslovakian cantilever high-wing monoplane with a fairly orthodox design. Details of the performance, construction, wing, ailerons, fuselage, landing gear, engines, characteristics, drawings, and photographs are provided.

"The results of a complete tank test of a model of a flying-boat hull of unconventional form, having a deep pointed step, are presented in this note. The advantage of the pointed-step type over the usual forms of flying-boat hulls with respect to resistance at high speeds is pointed out. A take-off example using the data from these tests is worked out, and the results are compared with those of an example in which the test data for a hull of the type in general use in the United States are applied to a flying boat having the same design specifications. A definite saving in take-off run is shown by the pointed-step type" (p. 1).

"With the aid of the method of J. Lotz, the writer undertook to solve theoretically the lift distribution along the span of an airplane wing, when the outline of the wing is uneven. This problem arises in the case of a mid-wing monoplane with embedded engine nacelles. The fuselage and the nacelles were considered as aerodynamically profiled, that is, as lift-producing parts. The task was therefore to determine not only the disturbance caused by the fuselage and nacelles, but also their share in the total lift of the wing" (p. 1).

Circular describing the Fokker F.XX, which is a three-engine high-wing cantilever monoplane with retractable landing gear and tail wheel. Details of the wing, fuselage, cockpit, cabin, covering and cowling, control surfaces, landing gear, power plant, fuel and oil systems, characteristics, drawings, and photographs are provided.

A description of the Hamburg tank and carriage is provided as well as a layout of the control station and generator room.

"This report presents towing tests made in the N.A.C.A. tank of a parent form and five variations of a flying-boat hull. The beams of two of the derived forms were made the same as that of the parent and the lengths changed by increasing and decreasing the spacing of stations. The lengths of the two others of the derived forms were made the same as that of the parent while the beams were changed by increasing and decreasing the spacing of buttocks, all other widths being changed in proportion. The remaining derived form has the same length and beam as the parent, but the lines of the forebody were altered to give a planing bottom with no longitudinal curvature forward of the step" (p. 1).